Major sources of hydrocarbon emissions in a premixed charge compression ignition engine

Although premixed charge compression ignition (PCCI) combustion engines are praised for potentially high efficiency and clean exhaust, experimental engines built to date emit more hydrocarbons (HCs) and carbon monoxide (CO) than the conventional machines. These compounds are not only strictly controlled components of the exhaust gas of road vehicles but are also an energy loss indicator. The prime objective of this study was to investigate the major sources of the HCs formed in the combustion chamber of an experimental PCCI engine in order to suggest some effective technologies for HC reduction. In this study, to explore the dominant sources of HC emissions in both operation modes, a single cylinder engine was prepared such that it could operate using either conventional diesel combustion or PCCI combustion. Specifically, the contributions of the top-ring crevice volume in the combustion chamber and the bulk quenching of the lean mixture were investigated. To understand the influence of the shape and magnitude of the crevice on HC emissions, the engine was operated with 12 specially prepared pistons with different top-ring crevices installed one after another. The engine emitted proportionally more HCs as the depth of the crevice increased as long as the width remained narrower than the prevailing quench distance. The top-ring-crevice-originated exhaust HCs comprised approximately 31% of the total HC emissions in the baseline condition. In a series of tests to estimate the effects of bulk quench on exhaust HC emissions, intake air was heated from 300K to 400K in steps of 25K. With the intake air heated, HC and CO emissions decreased with a gradually diminishing rate to zero at 375K. In conclusion, the most dominant sources of HC emissions in PCCI engines were the crevice volumes in the combustion chamber and the bulk quenching of the lean mixtures. The key methods for reducing HC emissions in PCCI engines are minimizing crevice volume in the combustion chamber and maximizing intake air temperature allowed based on the permissible NOx level.     

Comparative analysis of vehicle brake data in the ministry of transport test on the roller brake tester and on flat ground

This study performs a comparison between what occurs when braking on a Ministry of Transport (MOT) brake tester and on flat ground. The tire pressure is changed, but the other parameters remain constant. The results from this research and from the in-depth comparative study conducted by the mechanical engineering staff in the mechanical laboratory at the Miguel Hernández University in Elche have led to the following main conclusions: By varying the tire pressure, false results can be obtained with the MOT brake tester, which means that, if the tires are inflated at a low pressure but the brakes are in good condition, the vehicle will not pass the MOT. Conversely, if the brakes are in poor condition but the tire pressure is higher than what is recommended by the manufacturer, a false pass is produced. This article shows that the MOT brake testing equipment is often wrong and inexact, and the data and graphs presented prove that the tire pressure is a determining factor when assessing the condition of brakes.     

Aerodynamic design optimization of rear body shapes of a sedan for drag reduction

This study proposes an aerodynamically optimized outer shape of a sedan by using an Artificial Neural Network (ANN), which focused on modifying the rear body shapes of the sedan. To determine the optimization variables, the unsteady flow field around the sedan driving at very fast speeds was analyzed by CFD simulation, and fluctuations of the drag coefficient (C _D ) and pressure around the car were calculated. After consideration of the baseline result of CFD, 6 local parts from the end of the sedan were chosen as the design variables for optimization. Moreover, an ANN approximation model was established with 64 experimental points generated by the D-optimal methodology. As a result, an aerodynamically optimized shape for the rear end of the sedan in which the aerodynamic performance is improved by about 5.64% when compared to the baseline vehicle is proposed. Finally, it is expected that within the accepted range of shape modifications for a rear body, the aerodynamic performance of a sedan can be enhanced so that the fuel efficiency of the sedan can be improved. The YF SONATA, a sedan manufactured by Hyundai Motors Corporate, played a major role in this research as the baseline vehicle.     

A self-powering system based on tire deformation during driving

Tire intelligence is vital in the improvement of the safety of vehicles because the tire supports the car body and is the contact point between the vehicle and the road. To create an intelligent tire, sensors must be installed to measure the behavior of the tire. However, it is difficult to apply a wired sensor system on the wheel of the tire. Hence, it is necessary to implement a self-powering, wireless system (a type of energy harvesting system) that can be mounted inside the tire. The purpose of this study is to convert the strain energy caused by deformation of the tire while driving into useful electrical energy to supply the sensor system. A flexible piezofiber is utilized for the energy conversion. The variation in strain, due to changes in speed, load, and the internal pressure of the tire, was measured along two axial directions to evaluate the amount of available strain energy. The amount of strain changed from 0.15% to 0.8%. To predict the amount of available energy from a tire, we perform an analysis of the relationship between the strain and the voltage. In addition, experiments for impedance matching between piezofiber and related circuits were conducted to optimize the external loads for transferring energy efficiently. Based on the procedure mentioned above, at least 0.58 mJ of electrical energy can be generated by using the laterally oriented strain (1500 to 2500 micro strain). The result of this study is expected to enhance the potential realization of self-generating wireless sensor systems for so-called ??intelligent?? tires.     

High-strain-rate fracture of adhesively bonded composite joints in DCB and TDCB specimens

Double-cantilever beam (DCB) and tapered double-cantilever beam (TDCB) specimens are the test configurations most commonly used to measure the fracture toughness of composites and adhesive joints. Strain rates of 1 to 18.47 m/s were applied to the test specimens via high-speed hydraulic test equipment. Because the fracture occurs through the adhesively bonded joints and the cracks grow rapidly, the crack length and beam displacement were recorded by a high-speed camera. An energy range from 0 to 10 J was often observed in the high-strain-rate fracture experiments for nonlinear plastic behavior of the dynamically loaded adhesively bonded DCB and TDCB specimens. The range of energy release rates (fracture energy) for TDCB specimen was 2 to 3 times higher than that of a DCB specimen for all high strain rates. The fracture energy of automotive adhesive joints can be estimated using the experimental results in this study for the fracture toughness (G_IC) under high rates of loading. The crack grows as the applied fracture energy exceeds the value of the critical energy release rate (G_IC) at the crack tip. The energy release rate was calculated using the fracture mechanics formula. The key fracture mechanics parameter, the fracture energy GIC, was ascertained as a function of the test rate and can be used to assess and model the overall joint performance.     

Fuel consumption of fuel cell hybrid vehicles considering battery SOC differences

Fuel cell hybrid vehicles (FCHVs) have become one of the most promising candidates for future transportation due to current energy supply problem and environmental problem. Fuel economy is an important factor in FCHVs. In order to properly evaluate the fuel economy of an FCHV, the initial battery state of charge (SOC) and the final battery SOC have to be identical so that the effect of the battery energy usage on the fuel economy is neglected. In the simulation or in the real driving, however, the final battery SOC is usually different from the initial battery SOC, and the final battery SOC often depends on the power management strategy. To consider the difference between the two battery SOC values, the concept of equivalent fuel consumption is presented by two methods. One is based on the relationship between delta SOC and delta fuel consumption, and the other is based on the optimal control theory. Two rule-based power management strategies for an FCHV are presented, and for each strategy, the fuel economy is evaluated based on the two methods. The characteristics of the two methods are discussed and compared, and the superior one is selected based on the comparison.     

不同稳定剂对SBS改性沥青稳定效果的对比研究

通过试验测试不同老化时间样品的针入度、软化点和延度比较其相容性和路用流变学性能指标的变化,分析体系宏观稳定性和稳定剂性能特征,并通过形态结构照片分析稳定剂改善的效果。结果表明,加入稳定剂后改性沥青的高温储存稳定性明显改善,同时加入FD-06无硫稳定剂的改性沥青在热储存过程中性能更加稳定,不易离析。沥青中的部分组份具有化学活性,利用其活性点,引入带有活性基团的反应物,并通过被引入分子的化学结构的调节改善SBS与沥青的相容性,从而制备储存稳定性良好的SBS改性沥青。化学改性技术的应用提高了路用改性沥青的性能/价格比。     

A fundamental investigation of tilt control systems for narrow commuter vehicles

One way of addressing traffic congestion is by efficiently utilizing the existing highway infrastructure. Narrow tilting vehicles that need a reduced width lane can be part of the solution if they can be designed to be safe, stable, and easy to operate. In this paper, a control system that stabilizes the tilt mode of such a vehicle without affecting the handling of the vehicle is proposed. This control system is a combination of two different types of control schemes known as steering tilt control (STC) and direct tilt control (DTC) systems. First, different existing variations of both STC and DTC systems are considered and their shortcomings analysed. Modified control schemes are then suggested to overcome the deficiencies. Then a new method of integrating these two control schemes that guarantees smooth switchover between the controllers as a function of vehicle velocity is proposed. The performance of the proposed STC, DTC, and integrated systems is evaluated by carrying out simulations for different operating conditions and some experimental work. The design of a second-generation narrow tilting vehicle on which the developed control system has been implemented is presented.     

Comparison of HC species from diesel combustion modes and characterization of a heat-up doc formulation

This study summarizes engine speed and load effects on HC species emissions from premixed charge compression ignition (PCI) and conventional diesel combustion, and it evaluates diesel oxidation catalyst (DOC) formulations on a gas flow reactor for the purpose of diesel particulate filter regeneration or lean NO_x trap desulfation. HC emissions are sampled simultaneously by a Tedlar bag for light HC species and by a Tenax TA™ adsorption trap for semi-volatile HC species, and they are analyzed by gas chromatography with a flame ionization detector. The bulk temperature and residence time during combustion are key parameters that are important for understanding the effects of speed and load on engine-out HC emissions. The degree of post-flame oxidation is higher in PCI than in conventional combustion, and it is increased for PCI with a higher speed and load, as indicated by a lower fuel alkanes/THC ratio, a higher alkenes/fuel alkanes ratio, and a higher methane/THC ratio. Ethene and n-undecane are two representative HC species, and they are used as a surrogate mixture in the gas flow reactor to simulate PCI and conventional combustion with in-cylinder post fuel injection. Among the three DOC formulations tested, the catalyst with constituent precious metals of platinum and palladium (PtPd) showed the best light-off performance, followed by PtPd with an addition of cerium dioxide (PtPd+CeO₂), and platinum (Pt), regardless of exhaust compositions. Conventional combustion exhaust composition shows a lower light-off temperature than that of PCI, regardless of catalyst formulation.     

Fatigue design for plug/ring type gas welded joints of sts301l including welding residual stresses

This paper presents a fatigue design method for plug and ring type gas welded joints, which incorporates welding residual stress effects. A non-linear finite element analysis (FEA) was first performed to simulate the gas welding process. The numerically predicted residual stresses of the gas welds were then compared to experimental results measured using a hole drilling method. In order to evaluate the fatigue strength of the plug and ring type gas welded joints, a stress amplitude (σ _a ) _R taling the welding residual stress of the gas weld into account was introduced and is based on a modified Goodman equation incorporating the effect of the residual stress. Using the stress amplitude (σ _a ) _R , the ΔP-N _f relations obtained from fatigue tests for plug and ring type gas welded joints having various dimensions and shapes were systematically rearranged into (σ _a ) _R -N _f relations. It was found that the proposed stress amplitude (σ _a ) _R could provide a systematic and reasonable fatigue design criterion for the plug and ring type gas welded joints.