国外拖曳线列阵声纳技术现状与发展趋势

重点阐述了拖曳线列阵声纳的技术特点,介绍了西方主要国家海军拖曳线列阵声纳的技术现状,总结了其技术发展趋势。     

基于PLC控制的船用蓄电池充电装置设计

为减轻船用蓄电池充电时的劳动强度,降低充电操控复杂程度,提高对蓄电池充电的自动化和智能化水平,本文设计了PLC控制的船用大电流蓄电池充电装置,介绍了该装置的系统结构及其软硬件设计.整个充电过程,基本实现了自动控制,并能有效实现充电过程中过压、过流等报警提示、故障跳闸保护等.充电过程监测界面简洁直观,操作灵活方便.     

Engine performance and toxic gas analysis of biobutanol-blended gasoline as a vehicle fuel

A comprehensive study evaluating the performance of biobutanol-blended gasoline in passenger cars was conducted because biobutanol is considered a better biofuel than bioethanol as it has no water solubility and it has a higher caloric value, giving it a higher energy value. Several kinds of samples—suboctane gasoline, 8 volume percentage and 16 volume percentage biobutanol—blended gasoline, and a 10 volume percentage MTBE-blended market sample (as the oxygencontaining gasoline)-were tested to evaluate the engine performance in terms of the detergency of the intake valves and combustion chambers, power, emissions, and fuel efficiency. Additionally, the toxicity of the emissions from these biobutanolblended samples was tested in order to assess the viability of biobutanol as one of the competitive potential substitutes for MTBE as an oxygenator in the near future. The results show that biobutanol-blended gasoline samples had relatively better detergency, relatively higher power, and similar levels of emissions compared with those of MTBE-blended gasoline. Formaldehyde was emitted from all of the samples at almost the same levels and within the error range, whereas biobutanolblended gasoline samples emitted approximately three times the amount of acetaldehyde than did the suboctane gasoline. This study shows that biobutanol is one of the best alternative bioalcohol fuels for use in the near future.     

摩托车塑料件涂装工艺

塑料件的前处理目的是提高涂料对塑料的附着力和减少塑料表面上的各种缺陷,从而改善涂层质量;目前,主流的前处理工艺是采用化学处理方法,经低温脱脂水洗,表面活化后烘干。油漆涂装常规生产线大多采用人工喷涂;烘干方式有三喷二烘、三喷一烘或二喷一烘等,但以三喷一烘和二喷一烘最为常见。     

CFD-based method of determining form factor <Emphasis Type="Italic">k</Emphasis> for different ship types and different drafts

The value of form factor k at different drafts is important in predicting full-scale total resistance and speed for different types of ships. In the ITTC community, most organizations predict form factor k using a low-speed model test. However, this method is problematic for ships with bulbous bows and transom. In this article, a Computational Fluid Dynamics (CFD)-based method is introduced to obtain k for different type of ships at different drafts, and a comparison is made between the CFD method and the model test. The results show that the CFD method produces reasonable k values. A grid generating method and turbulence model are briefly discussed in the context of obtaining a consistent k using CFD.     

实船舵空化现象试验观察

空化是高航速下水面舰船螺旋桨及舵等附体上常见的现象,空化的产生会带来振动、噪声和空蚀等一系列问题,直接影响舰船的舒适性和局部结构的安全性.而由于国内有关实尺度舵空化数据的缺乏,导致人们对于实船舵空化的状况仍知之甚少.本文通过试验方法观察了某一实船舵在一定航速、一定舵角下的空化状况,获得了实船舵空化出现的位置及程度,为实尺度舵空化问题的认识和优化提供了一定参考.     

A hybrid firefly algorithm for optimizing fractional proportional-integral-derivative controller in ship steering

In this paper, a new algorithm which integrates the powerful firefly algorithm(FA) and the ant colony optimization(ACO) has been used in tracking control of ship steering for optimization of fractional-order proportional-integral-derivative(FOPID) controller gains. Particle swarm optimization(PSO) algorithm is also used to optimize FOPID controllers, and their performances are compared. It is found that FA optimized FOPID controller gives better performance than others. Sensitivity analysis has been carried out to see the robustness of optimum FOPID gains obtained at nominal conditions to wide changes in system parameters, and the optimum FOPID gains need not be reset for wide changes in system parameters.     

GPS天线线型对AUV阻力和尾流场的影响

靠近艉部的GPS天线线型对AUV的阻力以及桨盘面处的伴流品质有直接影响。高品质的伴流场能有效地降低噪声并提高水动力性能。为了获得最优的GPS天线线型,以某自主式水下机器人(AUV)为母型,采用ICEM-CFD、Fluent等CFD软件,结合RANS方法和SSTκ-ω模型对搭载不同线型GPS天线的AUV进行数值计算。研究结果表明GPS天线设计前倾角可以有效降低天线的阻力,从而降低AUV受到的整体阻力。具有一定前倾角和尾端曲线的GPS天线有利于改善AUV尾部伴流特性,减小桨盘面伴流速度的不均匀度。     

复杂条件下浅埋暗挖地铁车站施工地表沉降规律分析

文章以沈阳地铁中街站大跨度隧道工程为研究对象,应用FLAC3D计算软件,对复杂条件下浅埋暗挖大跨度隧道引起的地表沉降变形特征进行了数值模拟。根据洞桩法施工开挖方案,紧密结合工程实际,将动态施工开挖过程划分五个工况进行模拟,分析各施工工况对地表变形的影响和分布规律,并按工程信息化施工要求事前将预测数据提供施工单位,以指导施工控制地表沉降。模拟结果表明,采用洞桩法开挖施工过程中,对地层土体扰动较大,明显影响隧道中心附近地表变形的步序是小导洞开挖和初期支护扣拱施工阶段,约占最终沉降量的70%;而其他步序影响较小。最终,地表沉降在隧道横向分布呈"W"形态。模拟结果与现场监测数据具有较好的拟合性,表明利用数值分析方法预测大跨度隧道施工期地表沉降是可靠的。     

A review of the Effect of α/W ratio on fracture toughness （Ⅱ） experimental investigation in LEFM

In part I of this series, experimental investigation in EPFM （elastic-plastic fracture mechanics） had been discussed. In this paper, experimental investigation in LEFM （ linear elastic fracture mechanics） is given. Fracture toughness tests had been carried out on three different strength steels, using both through-cracked specimens with different α/W ratio and semi-elliptical cracked specimens with variable crack size and shape. Results show that the fracture toughness KIC increases with decreasing α/W when α/W 〈 0.3 for three-point-bend specimens, and that for α/W 〉 0.3, it is independent of α/W. Shallow crack specimens, both through-cracked and surface-cracked, gave markedly higher values than deeply notched specimens. However, the effect of crack shape on fracture toughness is negligible. Results also show that the LEFM approach to fracture is not tenable for design stresses where αc is often very small, far less than 2.5 （ KIC/σy）^2.