A Comparison of Various Computer Simulation Models for Predicting the Directional Responses of Articulated Vehicles

This paper presents the results of a comparative study of the predictions, made using computer simulation models of different levels of complexity, of the directional responses of commercial articulated vehicles in steady-state and lane-change maneuvers. The differences in the predictions obtained using various models are examined and are compared with available experimental data. The objective of this study is to compare the capabilities and limitations of various simulation models for predicting the directional behavior of articulated vehicles.     

Aircraft Ground Dynamics

The state-of-the-art in analysing a number of ground manoeuvring processes on aircraft is described. The mathematical models are as good as the data supplied to them.     

Dynamic Performance of a Bulkhead Flat Car

The dynamic performance of a flat car is studied herein. The performance indices include roll angles, lateral accelerations, center plate loads, side bearing loads, wheel loads and spring deflections. These variables are maximum when the car is running at its critical speed, corresponding to either the rock and roll, or the bounce mode. The Association of American Railroads' (AAR) Flexible Carbody Model was used. The input for vertical track irregularities used in the simulation was generated from published spectra for U.S. Federal Railroad Administration (FRA) Class 4 track. After studying the car's performance with various column loads and spring suspensions, it was found that the most commonly used column load of 4,000 lbs. (17.8 kN) should be used. The spring suspension used in the original car design should also be adopted, in order to avoid spring bottoming.     

Computer-Simulation of the Dynamical Curving Behaviour of a Railway-Bogie

This paper describes the modelling of a two axle railway-bogie with variable design configurations and its application in the investigation of the behaviour in transitional and circular curves. Several results indicate possibilities to improve the curving properties and recommend the usage of forced-steering bogies, which show better performance in narrow curves without unbearable sacrifices to high-speed-behaviour on straight track.     

Development of an LIF image processing technique for measuring drop sizes in a pre-swirl spray

Depth of field effects in laser sheet imaging were considered for droplet sizing of a pre-swirl spray. A pre-swirl spray is formed before the hollow-cone type main-swirl spray from a D.I. gasoline injector, and shows transient characteristics with high axial velocity. A microscopic imaging technique was applied to obtain high spatial resolution LIF tomograms of the pre-swirl spray. A 1 mm thick Nd:YAG laser sheet was used as a light source to make the LIF tomograms that were imaged using a high-resolution CCD camera. The droplet sizing of the pre-swirl spray was carried out using an image processing technique. In the image processing procedure, the laser sheet-straddling large-sized droplets were carefully taken into account to remove the errors caused by the depth of field effects from the limited thickness and the energy distribution of the laser sheet. The mean intensity of the individual droplets and the line profile of the LIF signal around the droplet edge were inspected to screen the laser sheet-straddling large-sized droplets. In order to consider the effects of the size-dependent LIF signal intensity, the size-classified or ensemble-averaged mean intensity of the individual droplets was introduced. The mean droplet sizes such as AMD and SMD were calculated using only screened droplets, and they slightly increase before considering the depth of field effects.     

Links between subjective and objective evaluations regarding the steering character of automobiles

This work presents an experiment on the relationships between subjective and objective evaluations of vehicle handling. Ten cars were examined objectively in several open-loop driving dynamics manoeuvres and subjectively by test persons in typical traffic situations. Results are extracted from a stationary test (the Slowly Increasing Steer Test), and a dynamical test (the Frequency Response Test). The subjective measurements are obtained from drivers on a rural road course via a questionnaire, which was developed to separately investigate the quantity level perception, the so-called “Niveau”, and the more qualitative “Liking”. These subjective “measurements” are embedded into a two-channel definition of “Steering Comfort” as a genus for “Steering Discomfort” and “Character”. The article concentrates on developing a statistical method for the consideration of correlations amongst the subjective/objective data. In doing so, the variance in example subjective Niveau ratings can be significantly explained by several objective quantities. Indicators for co-domains of validated discomfort characteristics and hints for endeavouring character Liking ranges are detected.     

3-D numerical and experimental analysis for airflow within a passenger compartment

People use cars so frequently that they always consider the air-conditioning, and thermal comfort of the driver and passenger when buying a new car. Therefore accurate simulation of the thermal performance of automobile air conditioners to improve human comfort has become increasingly important. In order to improve the thermal comfort of passengers, 3-D flow motion and thermal behavior within vehicles must be analyzed. In this paper, a numerical simulation was used to investigate thermal behavior in a vehicle. Because air temperature at an air vent is related to the cooling capacity of the air conditioner, the cooling capacity was calculated using ɛ-NTU (effective number of transfer unit) theoretical equations. Using the air temperature relationship between inlet and outlet vents as boundary conditions, a 3-D unsteady κ-ɛ turbulent model was used to give a transient analysis simulation of the temperature field and flow conditions in a vehicle’s passenger cabin. Cooling cycle analysis and conjugate heat transfer analysis at the inside surface of the cabin’s ceiling, floor and sides were also considered. The predicted temperature distributions in the vehicles passenger cabin were in good agreement with those obtained experimentally.     

Vehicle interior noise model based on a power law

Identifying the components of a vehicle’s interior noise is important in many phases of the noise, vibration, and harshness (NVH) development process. Many test methods that have been widely used in the automobile industry to separate noise sources are based on system identification methods in the frequency domain. However, none of the frequency response function-based methods can directly estimate the wind noise component. In this article, an analytical model for the interior noise level based on a simple power law was developed. It was assumed that the mean squared acoustic pressure for the interior noise could be obtained by summing up those of the wind noise, road noise, and background noise. The wind noise and road noise were further assumed to depend only on wind speed and the vehicle’s driving speed, respectively, and to follow a simple power law. The resulting analytical model includes five parameters that can be optimized for the vehicle and the road. The validity of the model was verified by using data obtained from cruise tests performed on a proving ground for cruise speeds ranging from 40 km/h to 130 km/h. The model is applied to the overall and 1/3-octave bands of interior noise and is shown to describe the data trends fairly well. For the test vehicle used in the present work, the overall mean squared pressures for the wind and road noise components are shown to be proportional to the wind speed to the 5.8 power and to the driving speed to the 3.4 power, respectively.     

Parameter identification for a LuGre model based on steady-state tire conditions

The purpose of this study was to effectively identify parameters for a LuGre friction model based on experimental measures. In earlier work related to this study (Yang et al., 2009), which was based on the characters of polygonal wear (Sueoka and Ryu, 1997), we showed a frictional vibration model for a mass on a moving belt. This model reflected lateral vibrations caused by velocity and toe-in angle. An important aspect of the present study is the improved friction model. A previous friction model, which divided the process into four parts, expressed the sable excited vibration well but failed to reflect the hysteresis loop change when vehicles accelerated or decelerated continuously. A LuGre friction model can solve this problem, but several model parameters must be obtained experimentally. We measured contact width and length of tires as vertical pressure changed; this provided a theoretical basis for apparent stiffness of a unit of tire tread. Based on tire data from Bakker E’s article in a SAE paper from 1987, we identified the Stribeck exponent and Stribeck velocity in LuGre. Then, the results were implemented in a vibration system that verified the rationality of the data.