Improving the predictiveness of the quasi-d combustion model for spark ignition engines with flexible intake systems

Fast and predictive simulation tools are prerequisites for pursuing simulation based engine control development. A particularly attractive tradeoff between speed and fidelity is achieved with a co-simulation approach that marries a commercial gas dynamic code WAVE™ with an in-house quasi-dimensional combustion model. Gas dynamics are critical for predicting the effect of wave action in intake and exhaust systems, while the quasi-D turbulent flame entrainment model provides sensitivity to variations of composition and turbulence in the cylinder. This paper proposes a calibration procedure for such a tool that maximizes its range of validity and therefore achieves a fully predictive combustion model for the analysis of a high degree of freedom (HDOF) engines. Inclusion of a charge motion control device in the intake runner presented a particular challenge, since anything altering the flow upstream of the intake valve remains “invisible” to the zero-D turbulence model applied to the cylinder control volume. The solution is based on the use of turbulence multiplier and scheduling of its value. Consequently, proposed calibration procedure considers two scalar variables (dissipation constant C _β and turbulence multiplier C _M ), and the refinements of flame front area maps to capture details of the spark-plug design, i.e. the actual distance between the spark and the surface of the cylinder head. The procedure is demonstrated using an SI engine system with dual-independent cam phasing and charge motion control valves (CMCV) in the intake runner. A limited number of iterations led to convergence, thanks to a small number of adjustable constants. After calibrating constants at the reference operating point, the predictions are validated for a range of engine speeds, loads and residual fractions.     

Hydrographic conditions affecting two fishing grounds of Mallorca island (Western Mediterranean): during the IDEA Project (2003–2004)

This paper describes the hydrographic conditions observed during six surveys carried out during 2003 and 2004, in the framework of the “IDEA Project” (acronym for “Influence of oceanographic structure and dynamics on demersal populations in waters of the Balearic Islands”). The surveys were developed on the shelf and slope of Mallorca Island, in particular in two fishing grounds at the north and south of the Mallorca channel. Periodic movements of the fishing fleet between these two areas have been regularly reported, suggesting a seasonal variability of the resources which could be in turn associated with the hydrodynamic variability. With this motivation, water masses affecting these grounds have been identified and their seasonal variability has been studied. Different oceanographic and environmental conditions have been found between the two fishing grounds. These differences are related to the presence of mesoscale structures, associated with the Western Mediterranean Intermediate Water (WIW) at the north of the Ibiza channel and big gyres detached from the Algerian Current. The former has been shown to have influence on the regional oceanic circulation and the latter could affect the progress of fresh Atlantic Water (AW) towards the channels and make possible the presence of high salinity values at intermediate waters at the south of Mallorca Island. Historical data from other oceanographic cruises carried out in the region are finally used to discuss the interannual variability of these mesoscale structures.     

Combustion development of a Bi-Fuel engine

Environmental improvement and energy issues are increasingly becoming more important as worldwide concerns. Natural gas is a good alternative fuel that can help to improve these issues because of its large quantity and clean burning characteristics. This paper provides the experimental performance results of a Bi-Fuel engine that uses Compressed Natural Gas as its Primary fuel and gasoline as its secondary fuel. This engine is a modification of the basic 1.4-liter gasoline engine. Generally, on the unmodified base engine, torque and power for CNG fuel are considerably lower than gasoline fuel. In this paper, the influence of fuels on wall temperature, performance and emissions are investigated.     

Perturbation/correlation based optimal internal combustion engine tuning

This paper addresses the application of the perturbation/correlation method to optimizing the torque output of internal combustion engines. This application was inspired by observations of the limitations in current techniques of the automotive performance tuning industry. Performance issues such as errors from true optimum spark timing and fuel injector pulse width values as well as convergence were considered for optimal tuning. The ability of the system to deal with engine cycle-to-cycle variations and their effect on input parameters is also analyzed.     

Off-set crack propagation analysis under mixed mode loadings

An assessment was carried out herein to study the eccentricity of cracks subjected to mixed-mode loadings. Several loading locations relative to a central line were selected to induce mixed-mode loadings, which were computed using a finite element method. An adaptive meshing technique was adopted during the simulation of crack propagation to ensure the singularity of stress at the tip of the crack. The stress intensity failure criterion was used and programmed, and the node splitting technique was used when the stress intensity factor reached the fracture toughness of the material to simulate crack propagations. It was found that large variations in the stress intensity factor were observed when off-set cracks were used, and that K _II decreased when loading distance increased, but increased when the off-set crack distance was increased. Both crack eccentricity and loading distance played important roles in producing mixed-mode loading, compared to the influence of central cracks. Correction factors were introduced to modify the calculation of stress intensity factors under mixed-mode loadings. Simulations of crack propagation were also conducted to study the effects of crack eccentricities and loading distances. It was found that the crack length, the loading distance relative to the central crack and the crack eccentricity dominated calculations of the integrity of cracked structures.     

Modified lateral control of an autonomous vehicle by look-ahead and look-down sensing

This paper presents a modified lateral control method for an autonomous vehicle with both look-ahead and look-down sensing systems. To cope with sensor noise and modeling uncertainty in the lateral control of the vehicle, a modified LMI-based H lateral controller was proposed, which uses the look-ahead information of the lateral offset error measured at the front of vehicle and the look-down information of the vehicle yaw angle error between the reference lane and the centerline of the vehicle. To verify the safety and the performance of the lateral control, a scaled-down vehicle was developed, and the positioning of the vehicle was estimated with USAT. The proposed controller, which uses both look-ahead and look-down information, was tested for lane changing and reference lane tracking with both simulation and experiment. The simulation and experimental results show that the proposed controller has better tracking and handling performance compared with a controller that uses only the look-ahead information of the target heading angle error.     

License plate extraction method for identification of vehicle violations at a railway level crossing

The primary cause of most railroad accidents is vehicle entry into railway level crossings despite warning messages. To identify drivers who violate railway level crossing regulations, vehicle license plate recognition can be applied at railway level crossings. The purpose of this paper is to present an effective method for extracting the license plate region from vehicle images taken at railway level crossings. The method proposed in this paper uses the variation in the gray-level values across the image of a license plate. For license plate region extraction, the character region is first recognized by identifying the character width and the difference between the background region and the character region. The license plate region is then extracted by finding the inter-character distance in the plate region. In addition, the license plate type is identified by the difference in the gray-level value between the background region and the character region. The proposed method is effective in solving the current challenges in extracting the license plate region from the damaged frames of license plates issued for domestic use, including new types of license plates. According to the experimental results, the proposed method yields a high extraction rate of 99.5% for vehicle license plates.     

Piston-temperature measuring system using electromagnetic induction with verification by a telemetry system

The development of an inner-piston-chamber temperature measurement system is a necessary step in engine development or when solving other fundamental problems related to automotive engines. There are various pre-existing measurement methods available, e.g., the linkage method, piston telemetry, templog, and the electromagnetic induction method. In this study, we first redesigned the coil sensor used in the electromagnetic induction method using PEEK and then used Taguchi methods to reduce the number of experiments in the development process and finally utilized piston telemetry via Bluetooth to verify the precision and accuracy of the redesigned PEEK coil sensor and electromagnetic induction method. The results displayed a reproducibility within 0.5 degrees and an accuracy within 2 degrees Celsius.     

Performance optimization of CVT for two-wheeled vehicles

Continuously Variable Transmission (CVT) is one of the most promising automotive transmission technologies because of its continuously variable gear ratio and reduced shift shock. CVT is different from Manual Transmission and Automatic Transmission, and it is possible to operate the power source in its high efficiency region with CVT in the drive train. Several types of CVT exist that can be categorized based on the mechanism of power transmission, such as the belt pulley, traction drive, and hydrostatic types. This paper investigates the belt pulley CVT, which consists of a thrust actuator, driver pulley, belt, driven pulley, and preload spring of the output shaft. A complete CVT is constructed, and based on that a simulation program that analyzes the static performance of a CVT is implemented in Matlab/Simulink. From these simulation results, methods for improving the efficiency of the CVT are discussed. The coefficient of the torque capacity factor is proposed as affecting the matching between a power source and a CVT, and methods for improving the matching effect are also investigated.