Prediction of fatigue life and estimation of its reliability on the parts of an air suspension system

Air suspension systems have been implemented in various commercial vehicles, such as buses and special purpose trucks, because of the comfortable ride and easy height control. An evaluation of the durability of vehicle parts has been required for service life and safety starting in the early stages of design. The cyclic load applied to the vehicle can cause fatigue failure of parts, such as the suspension frame. This paper presents a method to predict the fatigue life of the suspension frame at the design stage of the air suspension system used in a heavy-duty vehicle. To estimate the fatigue life using the SN method, the Dynamic Stress Time History (DSTH) is necessary for the part of interest. DSTH can be obtained from the results of the flexible body dynamic analysis using the Belgian road simulation and the Modal Stress Recovery (MSR) method. Furthermore, the reliability of the predicted fatigue life can be evaluated by considering the variations in material properties. The probability and distribution of the expected life cycle can be obtained using experimental design with a minimum number of simulations. The advantage of using statistical methods to evaluate the life cycle is the ability to predict replacement time and the probability of failure of mass-produced parts. This paper proposes a rapid and simple method that can be effectively applied to the design of vehicle parts.     

Fault detection method for electric parking brake (EPB) systems with sensorless estimation using current ripples

A fault detection method with parity equations is proposed in this paper. Due to its low cost implementation, the velocity of the motor is not measurable in electric parking brake (EPB) systems. Therefore, residuals are not reliable when estimating the motor velocity with a low-resolution encoder. In this paper, we propose a fault detection method with sensorless estimation using current ripples that estimates the position and velocity of the motor by detecting periodical oscillations of the armature current caused by rotor slots. In addition, this method can estimate the position and velocity of the motor with less computational effort than a state observer. Moreover, the method is less sensitive to motor parameters than model-based estimation methods. The effectiveness of this method is validated with experimental data, and the simulation results show that various faults have their own residual patterns. Therefore, we can detect the presence of faults by monitoring the residual signals.     

Development of electrostatic diesel particulate matter filtration systems combined with a metallic Flow-Through Filter and electrostatic methods

A 3000 cc diesel engine attached to an engine dynamo was used to test three newly developed electrostatic Diesel Particulate matter filtration Systems (DPS 1, 2, and 3) under four steady-state engine operating conditions: idle, 2000 rpm with no load, and 2000 rpm under 25% and 50% loads. Of the two developed alternatives, DPS 1 and DPS 2, DPS 2 comprises an ionization section, electrostatic field additional section and Flow-Through Filter (FTF), which achieved almost 90% removal of particulate matter (PM) under the engine’s operating conditions, and the efficiency of the FTF was maintained between 20% and 50%. Comparing the long-term performance of DPS 2 and DPS 3 (effectively a serial combination of two DPS 2s) with a commercially-available Diesel Particulate Filter (DPF), the DPS 2 and DPS 3 achieved almost the same efficiency for removing PM as the DPF but had significantly improved (75%∼90% lower) differential pressure drops.     

Development of a new sound metric for impact sound in a passenger car using the wavelet transform

Vehicles can experience impacts due to harsh road conditions. Contact with an uneven road surface causes vehicles to vibrate, which generates a loud impact sound. The attenuation of such noise is important because car passengers may complain about the impact noise. However, perfect removal of impact noise is not possible because most of it is caused by external conditions. More research is needed on the objective attributes of impact noise; however, the problem of impact noise is not a simple matter because impact noise is transient in nature and reaches a high level instantaneously. In this paper, a new objective attribute of impact noise is designed using the wavelet transform, which is appropriate for analyzing nonstationary signals, such as an impact signal. The usefulness of the new objective attribute, which is a sound metric, is examined by comparing the mean subjective ratings for real impact noise in passenger cars. The new sound metric has better correlation with the mean subjective rating than currently existing sound metrics.     

Damper modeling for dynamic simulation of a large bus with MR damper

In this study, a large bus is tested to measure its dynamic response by the single-lane change test and the rapid stop test. A full car model is established by ADAMS/Car for computer simulation. For multibody modeling of a large bus, user-defined templates are used in the simulation. Simulation results of the single-lane change test and the rapid braking test are compared to the results of the physical experiments, in which several sensors are installed to measure the vehicle’s responses. The results obtained from the simulation show good agreement with the tests’ results. A dynamic model for the MR(magnetic-rheological) damper is also developed by employing the Magic Formula model, which is widely used in the nonlinear modeling of a tire. Bump simulation of a full car with the MR damper is carried out to verify the performance of the MR damper. The comparison of the simulation results obtained with the MR damper model to the results obtained with the traditional passive damper model showed improved response of the vehicle with the MR damper.     

Quality evaluation of car window motors using sound quality metrics

In this paper, a method to establish a decision criterion to evaluate the quality of small window motors using sound quality (SQ) metrics is suggested. Although the sound level radiated from the motor is relatively small compared to other sounds in a car, the sound from an abnormal motor gives an uncomfortable feeling and the impression of abnormal operation, which can lead to customer complaints. To construct an objective decision criterion, the correlation between the SQ metrics and the subjective decision on the passing or failure of the motor were investigated. Four representative SQ metrics, viz., loudness, sharpness, roughness, and fluctuation strength, were calculated for the collected samples. It was observed that the loudness and roughness of the motor sample group classified as abnormal was higher than those of the normal motors. For a single figure rating for motor quality, an evaluation index for the motor sound was generated by combining the correlated SQ metrics with proper weightings. Evaluation results on the specimens that were not employed in generating the quality evaluation index showed a reasonable agreement with the subjective test at 73%. The suggested quality check method can replace the current subjective decision procedure to identify the faulty motors.     

Piston-temperature measuring system using electromagnetic induction with verification by a telemetry system

The development of an inner-piston-chamber temperature measurement system is a necessary step in engine development or when solving other fundamental problems related to automotive engines. There are various pre-existing measurement methods available, e.g., the linkage method, piston telemetry, templog, and the electromagnetic induction method. In this study, we first redesigned the coil sensor used in the electromagnetic induction method using PEEK and then used Taguchi methods to reduce the number of experiments in the development process and finally utilized piston telemetry via Bluetooth to verify the precision and accuracy of the redesigned PEEK coil sensor and electromagnetic induction method. The results displayed a reproducibility within 0.5 degrees and an accuracy within 2 degrees Celsius.     

Performance optimization of CVT for two-wheeled vehicles

Continuously Variable Transmission (CVT) is one of the most promising automotive transmission technologies because of its continuously variable gear ratio and reduced shift shock. CVT is different from Manual Transmission and Automatic Transmission, and it is possible to operate the power source in its high efficiency region with CVT in the drive train. Several types of CVT exist that can be categorized based on the mechanism of power transmission, such as the belt pulley, traction drive, and hydrostatic types. This paper investigates the belt pulley CVT, which consists of a thrust actuator, driver pulley, belt, driven pulley, and preload spring of the output shaft. A complete CVT is constructed, and based on that a simulation program that analyzes the static performance of a CVT is implemented in Matlab/Simulink. From these simulation results, methods for improving the efficiency of the CVT are discussed. The coefficient of the torque capacity factor is proposed as affecting the matching between a power source and a CVT, and methods for improving the matching effect are also investigated.     

Fatigue life prediction of a rubber material based on dynamic crack growth considering shear effect

This paper suggests a fatigue life calculation method (A fatigue life calculation method is suggested) for rubber components based on the dynamic crack growth considering shear effect. Dynamic tearing tests were carried out, and the crack length was measured using an optical microscope to calculate the dynamic crack growth rate which characterizes and determines the fatigue life. The algorithm was numerically implemented in finite element code, ABAQUS standard, by using the user subroutine and applied to several rubber components. In the finite element analysis, deformation mode of an element was classified into tension and shear, and a weighting factor was multiplied to a strain energy density according to the degree of shear strain. Tension and compression of an elliptic dumbbell specimen was simulated in order to verify the material parameters of the suggested fatigue life prediction equation and to enhance the reliability of the algorithm. Finally, the fatigue life of a vehicle suspension bushing was calculated and compared with test. There were good agreements in the failure location and the magnitude of the fatigue life.     

Evaluation and visualization of stratified ultra-lean combustion characteristics in a spray-guided type gasoline direct-injection engine

To comply with reinforced emission regulations for harmful exhaust gases, including carbon dioxide (CO₂) emitted as a greenhouse gas, improved technologies for reducing CO₂ and fuel consumption are being developed. Stable lean combustion, which has the advantage of improved fuel economy and reduced emission levels, can be achieved using a sprayguided-type direct-injection (DI) combustion system. The system comprises a centrally mounted injector and closely positioned spark plugs, which ensure the combustion reliability of a stratified mixture under ultra-lean conditions. The aim of this study is to investigate the combustion and emission characteristics of a lean-burn gasoline DI engine. At an excess air ratio of 4.0, approximately 23% improvement in fuel economy was achieved through optimal event timing, which was delayed for injection and advanced for ignition, compared to that under stoichiometric conditions, while NO_x and HC emissions increased. The combustion characteristics of a stratified mixture in a spray-guided-type DI system were similar to those in DI diesel engines, resulting in smoke generation and difficulty in three-way catalystutilization. Although a different operating strategy might decrease fuel consumption, it will not be helpful in reducing NO_x and smoke emissions; therefore, alternatives should be pursued to achieve compliance with emission regulations.