Design and shared use of a terminal departure lounge for new large aircraft operations

New Large Aircraft (NLA) are new aircraft developments larger than any existing aircraft. The NLA's higher seat capacity will significantly impact passenger terminal design and operations. This paper focuses on the issues regarding the departure lounge. Deterministic queuing theory is used to determine the size and seating configuration of the lounge, as well as to decide whether a second level should be built to accommodate the increase in the number of passengers. The paper also discusses the use of the satellite section of a pier‐satellite terminal as a single lounge for the NLA. Spreadsheets are used to implement the analyses.     

Prediction of fatigue life and estimation of its reliability on the parts of an air suspension system

Air suspension systems have been implemented in various commercial vehicles, such as buses and special purpose trucks, because of the comfortable ride and easy height control. An evaluation of the durability of vehicle parts has been required for service life and safety starting in the early stages of design. The cyclic load applied to the vehicle can cause fatigue failure of parts, such as the suspension frame. This paper presents a method to predict the fatigue life of the suspension frame at the design stage of the air suspension system used in a heavy-duty vehicle. To estimate the fatigue life using the SN method, the Dynamic Stress Time History (DSTH) is necessary for the part of interest. DSTH can be obtained from the results of the flexible body dynamic analysis using the Belgian road simulation and the Modal Stress Recovery (MSR) method. Furthermore, the reliability of the predicted fatigue life can be evaluated by considering the variations in material properties. The probability and distribution of the expected life cycle can be obtained using experimental design with a minimum number of simulations. The advantage of using statistical methods to evaluate the life cycle is the ability to predict replacement time and the probability of failure of mass-produced parts. This paper proposes a rapid and simple method that can be effectively applied to the design of vehicle parts.     

Auto-ignition and micro-explosion behaviors of droplet arrays of water-in-fuel emulsion

The characteristics of auto-ignition and micro-explosion behaviors of one-dimensional arrays of fuel droplets suspended in a chamber with high surrounding temperature were investigated experimentally with various droplet spacings, numbers of droplet and surrounding temperatures. The fuels used were pure n-decane and emulsified n-decane with varied water contents ranging from 10 to 30%. All experiments were performed under atmospheric conditions with high surrounding temperatures. An imaging technique using a high-speed camera was adopted to measure ignition delay, flame lifetime, and flame spread speed. The camera was also used to observe micro-explosion behaviors. As the droplet array spacing increased, the ignition delay also increased, regardless of water content. However, the lifetime of the droplet array decreased as the droplet spacing increased. The micro-explosion starting time remained unchanged regardless of the number of the droplets or the droplet spacing; however, it tended to be delayed slightly as the water percentage and droplet spacing increased.     

Performance estimation model of a torque converter part I: Correlation between the internal flow field and energy loss coefficient

The objective of this paper is to improve the performance estimation model of the internal flow field of a torque converter. Compared with performance experiment results, the converter based on the one-dimensional model does not satisfy the performance requirements demanded in practice. Therefore, we need to develop more predictable and reliable performance estimation models. In order to obtain shape information on three-dimensional blade geometry, a process of reverse engineering conducts a torque converter assembly, impeller, turbine and stator. In addition, a CFD simulation including mesh generation and post-processing was carried out to extract equivalent parameters from the internal flow field. The internal flow field can be explained by analyze the correlation between a performance estimation model and CFD analysis. The equivalent performance model adopts the variation of energy loss coefficients for a given operating condition according to the application of a changing energy loss coefficient by the least mean squares method. The estimated equivalent model improves the agreement in performance between experiments and the theoretical model. This model can reduce the error to within about 3 percent. Furthermore, this procedure for predicted performance achieves eminence in the estimation of the capacity factor.     

Simulation of city bus performance based on actual urban driving cycle in China

This paper establishes the simulation model of a city bus on the basis of the EQ6110 bus prototype and its experimental data. According to the actual urban driving cycle, the fuel economy and the traction performance of the EQ6110 city bus have been simulated, and factors such as the driving cycle, the loss of power to engine accessories, the gear-shifting strategy, the fuel shut-off strategy of the engine, etc., which influence on the bus’s fuel economy, are also quantitatively analyzed. Some conclusions are drawn as follows: (1) driving cycles have a great influence on the fuel economy of a city bus; (2) under the typical urban driving cycle of the public bus in China, the engine fuel shut-off strategy can save about 1 to 1.5 percent of the fuel consumption; and (3) the optimized gear-shifting rules can save 6.7 percent of the fuel consumption. Experimental results verify that the fuel economy for the EQ6110 public bus is improved by 7.2 pecent over the actual Wuhan urban driving cycle of the current public bus in China.     

Effect on friction of engine oil seal with engine oil viscosity

Low viscosity engine oil can improve a vehicle’s fuel economy by decreasing the friction between the engine components. Frictional torque varies with the velocity change due to different viscosity characteristics of SAE grade 5W-20, 5W-30 and 5W-40 engine oils. The viscosity for each of these grades was measured to outline the effect low viscosity engine oils have on engine friction, which may lead to improved fuel economy. Engine oil seal frictional torque increases with the shaft rotational speed for all three engine oil grades. A decrease in engine oil seal frictional torque was confirmed when low viscosity engine oil was used. Also, the leak-free performance of the engine oil with the seal satisfied the life limit durability test criteria. Thus, low viscosity engine oil may be used to improve fuel economy by decreasing the frictional loss of the engine oil seal while having no negative impact on performance due to leak-free functioning.     

Lane-following method for high speed autonomous vehicles

This paper presents a steering control method for lane-following in a vehicle using an image sensor. With each image frame acquired from the sensor, the steering control method determines target position and direction, and constructs a travel path from the current position to the target position either as an Arc-path or S-path. The steering angle is calculated from the travel path thus generated, and the vehicle follows the travel path via motor-control. The method was tested using a vehicle dubbed as KAV (Korea Autonomous Vehicle) along an expressway (Seoul Inner Beltway) trajectory with a variety of radii (50 m ∼ 300 m) while traveling at a speed of 60 km/h to 80 km/h. Compared with an experienced human driver, the method showed little much difference in performance in terms of lane-center deviation. The proposed method is currently employed for high speed autonomous driving as well as for stop and go traffic.     

Automotive structure vibration with component mode synthesis on a multi-level

The recursive component mode synthesis method (RCMS) has been implemented for the finite element analysis model of an automobile structure as an efficient free vibration analysis tool. The RCMS method is intended to obtain a better performance relative to the block Lanczos method, which is a traditional method in the industry of obtaining eigenvalues, while obtaining the acceptable accuracy. A numerical example of the automobile finite element model demonstrates the outstanding performance of RCMS compared to the block Lanczos method.     

Public perceptions of the use of dynamic message signs

Intelligent transportation systems have been promoted as a means to improve both the efficiency and safety of the road network. The effectiveness of advanced technologies in improving road safety has been an area of research which has thus far yielded mixed results. In order to ensure that advanced technologies deliver on their intended outcomes, more research has to be devoted to understanding road users' perceptions and reactions to these systems. This study examines drivers' perceptions of the use of dynamic message signs and their self‐reported reactions to the messages displayed. In general, drivers support the use of highway electronic boards for traffic incident reports and weather information which have an impact on traffic delays and level of service. They also think that it is a good idea to display road safety messages and to remind drivers to drive safely and be courteous on the roads. Moreover, most drivers reported that they do read and think about the messages displayed and react positively to some of the road safety messages.     

Deconstructing development density: Quality, quantity and price effects on household non-work travel

Smart growth and transit-oriented development proponents advocate increasing the density of new land development and infill redevelopment. This is partly in order to reduce auto use, by reducing distances between trip origins and destinations, creating a more enjoyable walking environment, slowing down road travel, and increasing the market for transit. But research investigating how development density influences household travel has typically been inadequate to account for this complex set of hypotheses: it has used theoretically unjustified measures, has not accounted for spatial scale very well, and has not investigated potentially important combinations of measures. Using data from a survey of metropolitan households in California, measures of development density corresponding to the main hypotheses about how density affects travel—activity density affecting distance traveled, network load density affecting the speed of auto travel, and built form density affecting the quality of walking—are tested as independent variables in models of auto trip speed and individual non-work travel. Residential network load density is highly negatively correlated with the speed of driving, and is also highly correlated with non-work travel, both singly and in combination with other measures. Activity density and built form density are not as significantly related, on their own. These results suggest that denser development will not influence travel very much unless road level-of-service standards and parking requirements are reduced or eliminated.