Modeling residential sorting effects to understand the impact of the built environment on commute mode choice

This paper presents an examination of the significance of residential sorting or self selection effects in understanding the impacts of the built environment on travel choices. Land use and transportation system attributes are often treated as exogenous variables in models of travel behavior. Such models ignore the potential self selection processes that may be at play wherein households and individuals choose to locate in areas or built environments that are consistent with their lifestyle and transportation preferences, attitudes, and values. In this paper, a simultaneous model of residential location choice and commute mode choice that accounts for both observed and unobserved taste variations that may contribute to residential self selection is estimated on a survey sample extracted from the 2000 San Francisco Bay Area household travel survey. Model results show that both observed and unobserved residential self selection effects do exist; however, even after accounting for these effects, it is found that built environment attributes can indeed significantly impact commute mode choice behavior. The paper concludes with a discussion of the implications of the model findings for policy planning.

Performance characteristics of a supplementary stack-cooling system for fuel-cell vehicles using a carbon dioxide air-conditioning unit

In fuel-cell-powered vehicles, the fuel-cell system requires a thermal-management subsystem to dissipate heat released during the reaction of hydrogen with oxygen. When the stack generates power at a high rate, a large amount of heat is also generated. If cooling by the radiator is insufficient, a supplementary stack-cooling system is needed to maintain a safe operating temperature. In this study, the performance of a CO₂ air-conditioning unit for stack cooling was investigated under various conditions, and the relationship between cabin cooling and stack cooling was also studied. The coefficient of performance (COP) increased from 1.9 to 2.4, with an increase in cabin-air inlet flow rate from 0 to 8 m³/min. When the air-conditioning unit was turned off, the cooling capacity of the stack cooler was increased; correspondingly, as the cabin-cooling capacity was increased, that of the stack cooler decreased. With an increase in ambient-air inlet temperature from 38°C to 45°C, the COP decreased by 24%. Additionally, both the stack-cooling capacity and cabin-cooling capacity were decreased by about 12% and 16%, respectively, due to reduced heat transfer in the gas cooler as the ambient air inlet temperature was increased. It is expected that the experimental results can serve as a resource in designing a stack-cooling system using a CO₂ air-conditioning unit to enhance stack power generation and efficiency.     

Age and cross-cultural comparison of drivers’ cognitive workload and performance in simulated urban driving

Driving demands significant psychomotor attention and requires even more when drivers are engaged in secondary tasks that increase cognitive workload and divert attention. It is well established that age influences driving risk. Less is known about how culture impacts changes in attention. We conducted parallel driving simulations in the US and Korea to measure the extent to which age and culture influence dual-task performance. There were 135 participants divided into two groups: a younger group aged 20∼29, and an older group aged 60∼69. Whereas some differences by culture appeared in absolute control measures, the younger participants showed similar mean velocity and compensatory patterns associated with increased cognitive load in the urban setting; however, the results from the older samples were less similar.     

New procedure to estimate the brake warping in a roller tester

Vehicle systems such as the steering, brakes and suspension greatly influence vehicle safety. Therefore, these systems must be inspected to guarantee that they are functioning correctly and to certify that the vehicle is functioning at a satisfactory safety level. In disc brakes, warping is one of the principal reasons for vibrations and noise, and it contributes to diminished brake efficiency. Currently, the International Motor Vehicle Inspection Committee (CITA) demands disc brake warping inspections occur during periodic motor vehicle inspections (PMVIs); however, the procedure to carry out this inspection is not well defined. In this investigation, the warping phenomenon has been analyzed, and a new inspection procedure is proposed.     

Optimizing the shape of a bumper beam section considering pedestrian protection

This paper presents a design technique to optimize the shape of a vehicle bumper beam that satisfies both the safety requirements for a front rigid-wall impact and the regulations protecting pedestrians from lower leg injuries caused by bumper impacts. An intermediate response surface modeling (IRSM) technique was introduced to approximate the non-linear force-displacement curves obtained from the front impact analysis of a vehicle bumper. The accuracy of the IRSM model was tested by comparing its results with those of the non-linear finite element analysis. The maximum displacement error between the two models did not exceed 3%. Using pedestrian impact analyses based on the experimental arrangement of the Plackett-Burman design, the approximate functions describing the response values acting on the lower legs were calculated. The shape of the bumper beam was optimized by integrating the IRSM with the force-displacement model and the approximate functions on lower leg impact. The optimization results satisfied safety regulations on the maximum allowable displacement of the vehicle bumper, and also the regulations protecting pedestrians from lower leg injuries caused by bumper impacts.     

Effect of the number of fuel injector holes on characteristics of combustion and emissions in a diesel engine

The diesel combustion process is highly dependent on fuel injection parameters, and understanding fuel spray development is essential for proper control of the process. One of the critical factors for controlling the rate of mixing of fuel and air is the number of injector holes in a diesel engine. This study was intended to explore the behavior of the formation of spray mixtures, combustion, and emissions as a function of the number of injector hole changes; from this work, we propose an optimal number of holes for superior emissions and engine performance in diesel engine applications. The results show that increasing the number of holes significantly influences evaporation, atomization, and combustion. However, when the number of holes exceeds a certain threshold, there is an adverse effect on combustion and emissions due to a lack of the air entrainment required for the achievement of a stoichiometric mixture.     

考虑引桥工作状态下的短跨板桥的车致动力反应

通过把车辆和桥梁看作一个耦合系统来建立模型去求解桥梁的车致动力反应。文中研究了由AASHTO HS20卡车引起的不同跨径的短板桥的动力反应。利用参数分析来研究不同车速及不同路面状况所产生的效应。研究发现,引起桥梁动力反应峰值的临界车速遵循描述列车致桥梁共振的规则。分析中考虑了引桥状态的影响包括引桥桥头断层及引桥板形变。虽然引桥变形对桥梁的动力反应影响微小,但是在研究中却发现引桥桥头断层能在短跨板桥中引起显著的动力反应。该文对评价既有短跨径桥梁的动力性能有很大的意义,因此值得中国从业者借鉴。     

Traffic-balancing algorithm for can systems with dual communication channels to enhance the network capacity

The controller area network (CAN) is the dominant protocol for in-vehicle network (IVN) systems because it provides bounded transmission delay among electronic control units (ECUs) at data rates between 100 Kbps and 1 Mbps. Many automotive companies have chosen the CAN protocol for their chassis network system of intelligent vehicles. However, the increasing number of ECUs in intelligent vehicles and the need for more intelligent functions require a network system with more network capacity and real-time capability. As one approach to enhance the network capacity of a CAN system, this paper introduces a CAN system with dual communication channels. This paper also presents a traffic-balancing algorithm that predicts the traffic of each channel and allocates frames to the most appropriate channel. An experimental testbed using commercial off-the-shelf microcontrollers with two CAN controllers was used to demonstrate the feasibility of the traffic-balancing algorithm.     

沥青混合料烟雾与材料力学性能之间的关系

着重于研究热拌沥青混合料生产过程中产生的烟雾与沥青力学性能之间的关系,涉及的影响因素有温度、沥青种类以及一些动力学参数。研究者在试验室拌和机上安装了气体取样设备,能够在正常拌和的同时对热拌沥青混合料烟雾中的多环芳香烃(PAH)以及有机化合物(TOC)进行取样分析。通过对沥青材料进行室内性能指标的测试,发现在所有指标中回收沥青的复合模量与沥青烟雾排放量的相关性最好,因为它的结果同时反映了材料的物理性能以及沥青氧化和老化的程度。同时还建立了热拌沥青混合料烟雾排放与拌和参数以及混合料力学性能之间的关系。     

编者的话

近期。美国“三巨头“的命运一直受各方关注。原以为3月30日能有个基本的论断,谁知奥巴马政府又抛出给通用60天、给克莱斯勒30天的“最后期限”。其中唯一还未申请政府救援的福特公司最近成功削减债务达99亿美元;而克莱斯勒和菲亚特公司的合作现今看来也比较顺利,如果达成协议,联邦政府有可能追加60亿美元的贷款;唯独通用的命运依旧令人摸不着头脑。任通用CEO长达8年之久的瓦格纳被迫下台．其工作由前通用汽车公司总裁兼首席执行官Fritz Henderson接任。