Inventory,Classification, and Analysis of Special Management Areas Associated with U.S. Coastal Programs

Area-based management approaches may be beneficial in integrating sectoral, single-purpose laws and regulations; however, these benefits may not be attained if special area designations are equally sectoral or single-purpose in nature. Over 60 types of special management areas were documented under U.S. coastal programs, and a new classification scheme was developed to allow comparisons and analyses across programs. Results indicate that requirements and incentives for special area designations under the Coastal Zone Management Act did little to standardize or influence area-based management systems associated with state and territory coastal programs. Further, the absence of clear patterns within and between coastal programs with respect to special area policies suggests a limited commitment to this important aspect of coastal management. Continued research is needed to document the effectiveness of the various area-based management approaches presented in this article.     

Model-based analysis of the mechanical subsystem of an air brake system

Most commercial vehicles such as buses and trucks use an air brake system, often equipped with an S-cam drum brake, to reduce their speed and/or to stop. With a drum brake system, the clearance between the brake shoe/pad and the brake drum may increase because of various reasons such as wearing of the brake shoe and/or brake drum and drum expansion caused by high heat generation during the braking process. Hence, to ensure proper functioning of the brake system, it is essential that the clearance between the brake shoe and the brake drum is monitored. In this paper, we present a mathematical model for the mechanical subsystem of the air brake system that can be used to monitor this clearance. This mathematical model correlates the push rod stroke transients and the brake chamber pressure transients. A kinematic analysis and a dynamic analysis of the mechanical subsystem of the air brake system were performed, and the results are corroborated with experimental data.     

Cycle-simulation turbulence modelling of IC engines

Numerical simulations of IC engines are of high interest for automotive engineers worldwide. The simulation models should be as fast as possible, low-computational effort and predictive tool. The correct prediction of turbulence level inside the combustion chamber of spark ignition engines is the most important factor influencing to the engine working cycle. This paper presents a development of the k-ε turbulence model applied to the commercial cycle-simulation software with the high emphasis on the intake part. The validation was performed on two engine geometries with the variation of engine speed and load comparing the cycle-simulation results of the turbulent kinetic energy and in-cylinder temperature with 3-D CFD results. In order to apply the cycle-simulation turbulence model for the simulation of entire engine map, the parameterization model of turbulence constants was proposed. The parameterized turbulence model was optimized using NLPQL optimization algorithm where the single set of turbulence model parameters for each engine was found. A good agreement of the turbulent kinetic energy during the expansion was achieved when the turbulence affects the flame front propagation and combustion rate as well.     

Origin–destination table disaggregation using biproportional least squares estimation

This paper describes a group of techniques for disaggregating origin–destination tables for travel forecasting that makes explicit use of observed traffic on a network. Five models within the group are presented, each of which uses nonlinear least-squares estimation to obtain row and column factors for splitting trip totals from and to larger geographical areas into smaller ones. The techniques are philosophically similar to Fratar factoring, although the solution method is quite different. The techniques are tested on a full-sized network for Northfield, MN and are found to work effectively.     

Evaluating the energy performance of a SUV hybrid electric vehicle

This paper analyzes the energetic performance of the hybrid Lexus RX 400h, through on-board measurements. Several speed profiles were analyzed, for three driving types, successive stop and go cycles, three speed profiles, crossing an electronic toll collection booth, and a roundabout. In stop and go situations the internal combustion engine did not work (the torque needed to impulse the vehicle in the stop and go situations was only supported by the electric engines), as well as in the situations of constant low speeds (50 or 60 km h^?1). The auxiliary support given by the electric engines in the accelerations, as well as the importance of the energy regeneration system on the batteries’ load recovery is also demonstrated. When compared with similar conventional vehicles, the Lexus RX 400h has lower combined energy consumption between 1.2% and 60%.     

A regional railroad network optimization model for coal transportation

A regional railroad network is presented to evaluate the system's response to increased coal traffic. An optimal, multimodal, coal-shipping pattern is developed for the study region to minimize total costs and to efficiently use the existing network. A two-stage, general model allocates resources among demands and then assigns flows to the network according to efficiency criteria. The model is sufficiently general to permit modification for specific needs, assumptions and data. Government agencies and industries can apply the model in resource allocation decisions and transportation policy analysis.     

Finite element modeling of static tire enveloping characteristics

To investigate static tire enveloping characteristics, a three dimensional (3-D) finite element model is proposed. The vertical stiffness of the tire is studied on a flat surface with and without cleat. Tire rubber materials and cord layers are represented independently using “rebar” elements available in MSC Marc Mentat. Comparisons of numerical and experimental results are given to show the validity of the proposed model. It is shown that after a certain displacement, the results of the proposed model agree well with experimental results. In addition, the model results show that regardless of the type of the cleat placed under the rim center (hub center), all vertical force curves intersect after a certain displacement, which indicates typical static enveloping characteristics. Moreover, another typical characteristic of the radial tires that is unlike those of bias-ply constructions confirms that the contact patch does not expand laterally after a level vertical load is applied to the tire, which is directly related to fuel consumption and tire tread life.     

A risk model for the operation of container vessels

Commercial shipping of containerized goods involves certain risks for human safety and environment. In order to actively manage these risks, they must be identified, analyzed, modeled, and quantified. This requires a systematical analysis of design and operation of container vessels. Within the EU-funded research project SAFEDOR, a Formal Safety Assessment has been applied to establish the current safety level of generic container ships and to identify potential cost-effective risk control options. This paper describes a structured approach to develop the underlying high-level risk model. It is structured as risk contribution tree consisting of a series of fault trees and event trees for the major accident categories. Statistical analysis of casualty data is used to estimate the probability of occurrence. Finally, the summation overall individual risk contributions yields the current risk pro file for the operation of container vessels is presented as FN-curve.