A probabilistic damage tolerance concept for welded joints Part 2: a supplement to the rule based S–N approach

The first part of this paper presented the required statistics and stochastic models for reliability analysis of the fatigue fracture of welded plate joints. This present Part 2 suggests a probabilistic damage tolerance supplement to the design S–N curves for welded joints. The goal is to provide the practising engineer with simple tools that predict the reliability against fatigue fracture during service life. The impact of the chosen fatigue design factors (FDF) and the uncertainty in the applied stresses is revealed. The effect of an in-service inspection programme is also predicted. The results are presented as dimensionless matrices and suggested for use in support of decision-making at the design stage, without any advanced fracture mechanics modelling and stochastic simulation. One important advantage of this format is that the probability levels are presented regardless of actual weld class and target service life (TSL). This is obtained by introducing the FDF as a key parameter to the results. This parameter is defined as the ratio of predicted fatigue life over TSL. FDF is always calculated in the S–N approach which is mandatory in fatigue life prediction. Various welded details (classes) will have the same reliability level for the same FDF. This is true at the end of TSL and at earlier stages, i.e. fractions of TSL. The absolute value of TSL is immaterial for a given FDF. In the case of in-service inspection, the inspection interval is also given without dimensions as a fraction of TSL.

Only the influence of future scheduled inspections is treated. Updating based on actual inspection results is not included as the scope of work is inspection planning at the design stage. Results for some frequent cases occurring in practice are readily derived and presented.     

Fatigue design for plug/ring type gas welded joints of sts301l including welding residual stresses

This paper presents a fatigue design method for plug and ring type gas welded joints, which incorporates welding residual stress effects. A non-linear finite element analysis (FEA) was first performed to simulate the gas welding process. The numerically predicted residual stresses of the gas welds were then compared to experimental results measured using a hole drilling method. In order to evaluate the fatigue strength of the plug and ring type gas welded joints, a stress amplitude (σ _a ) _R taling the welding residual stress of the gas weld into account was introduced and is based on a modified Goodman equation incorporating the effect of the residual stress. Using the stress amplitude (σ _a ) _R , the ΔP-N _f relations obtained from fatigue tests for plug and ring type gas welded joints having various dimensions and shapes were systematically rearranged into (σ _a ) _R -N _f relations. It was found that the proposed stress amplitude (σ _a ) _R could provide a systematic and reasonable fatigue design criterion for the plug and ring type gas welded joints.     

Ergonomic and biomechnical analysis of automotive general assembly using XML and digital human models

Automotive general assembly requires many manual assembly operations to be carried out by human workers. Ergonomic analysis is an important part of the design and evaluation of products, jobs, tools, machines and environments for safe, comfortable and effective human functioning. Most recent researches have involved the evaluation of working conditions to prevent work-related musculoskeletal disorders. The majority of previous research on automotive companies has mainly considered the results of ergonomic analyses such as RULA (Rapid Upper Limb Assessment), REBA (Rapid Entire Body Assessment) and OWAS (Ovako Working Posture Analysis System). Analysis of static posture including reachability, clearances for arm, hand and tool has also been used to evaluate working conditions. However, in addition to static posture analysis, a biomechanical analysis in dynamic conditions should also be conducted. There are no integrated frameworks or standard schema for ergonomic analysis using digital human models in digital environments. The purpose of this paper is to propose a new framework for the evaluation of working conditions by ergonomic and biomechanical analysis using digital models based on XML standard schema, including: products, processes, manufacturing resources and human workers. This paper presents the analysis results using the proposed framework for automotive general assembly operations. We propose a new framework for the evaluation of the assembly operations and their environments. Then we apply a digital human model to the dynamic simulation of general automotive assembly operations based on standard schemas in XML and PPRH (Product, Process, Resource and Human). Using PPRH information based on a standard XML schema to analyze the ergonomic and biomechanical results, the engineer can visualize, analyze and improve assembly operations and working environments in automotive general assembly shops using digital models.     

Comparison of HC species from diesel combustion modes and characterization of a heat-up doc formulation

This study summarizes engine speed and load effects on HC species emissions from premixed charge compression ignition (PCI) and conventional diesel combustion, and it evaluates diesel oxidation catalyst (DOC) formulations on a gas flow reactor for the purpose of diesel particulate filter regeneration or lean NO_x trap desulfation. HC emissions are sampled simultaneously by a Tedlar bag for light HC species and by a Tenax TA™ adsorption trap for semi-volatile HC species, and they are analyzed by gas chromatography with a flame ionization detector. The bulk temperature and residence time during combustion are key parameters that are important for understanding the effects of speed and load on engine-out HC emissions. The degree of post-flame oxidation is higher in PCI than in conventional combustion, and it is increased for PCI with a higher speed and load, as indicated by a lower fuel alkanes/THC ratio, a higher alkenes/fuel alkanes ratio, and a higher methane/THC ratio. Ethene and n-undecane are two representative HC species, and they are used as a surrogate mixture in the gas flow reactor to simulate PCI and conventional combustion with in-cylinder post fuel injection. Among the three DOC formulations tested, the catalyst with constituent precious metals of platinum and palladium (PtPd) showed the best light-off performance, followed by PtPd with an addition of cerium dioxide (PtPd+CeO₂), and platinum (Pt), regardless of exhaust compositions. Conventional combustion exhaust composition shows a lower light-off temperature than that of PCI, regardless of catalyst formulation.     

Optimized design for a MacPherson strut suspension with side load springs

Undesired lateral force inevitably exists in a MacPherson suspension system, which is liable to damper rod’s side wear and promotes the damper’s inner friction decreasing the ride performance from the suspension system. Substituting a new side load spring with curved centerline for the conventional coil spring has been proven able to solve these problems and Multi-body Dynamics combining with Finite Elements Analysis may be an efficient method in optimizing its design. Therefore, taking a passenger car as example, a detailed multi-body dynamics model for the suspension system is built to simulate forces exerted on the damper and the minimization of its lateral component is selected as the design target for the spring. When the structure optimization of the side load spring is performed using FEA software ANSYS, its vertical and lateral elastic characteristics, supported by test data, are analyzed. After importing FEA results back to the suspension system, the dynamics simulation can be performed to validate the optimization result.     

Adaptive neuron control using an integrated error approach with application to active suspensions

This paper proposes a new neuron control strategy for an active vehicle suspension system, with the emphasis on the study of multivariable and uncertain suspension characteristics. The novelty of this strategy is in the use of integrated error, which consists of multiple output errors in the regulated plant. By combining the integrated error approach with the traditional neuron control (TNC), integrated error neuron control (IENC) is presented. It provides a direct control to the multiple outputs of the control plant simultaneously. Taking a quarter-car model as an example, the proposed control strategy is applied and comparative simulations are carried out with various vehicle parameters and road input conditions. Simulation results prove the effectiveness and robustness of the proposed IENC method. In addition, the newly proposed neuron scheme provides a simple yet efficient new possibility for the control of a class of uncertain multivariable systems similar to an active vehicle suspension.     

Immigration, residential location, car ownership, and commuting behavior: a multivariate latent class analysis from California

Using latent class cluster analysis, this paper investigates the spatial, social, demographic, and economic determinants of immigrants’ joint distribution among travel time, mode choice, and departure time for work using the 2000 Census long form data. Through a latent tree structure analysis, age, residential location, immigration stage, gender, personal income, and race are found to be the primary determinants in the workplace commute decision-making process. By defining several relatively homogeneous population segments, the likelihood of falling into each segment is found to differ across age groups and geography, with different indicators affecting each group differentially. This analysis complements past studies that used regression models to investigate socio-demographic indicators and their impact on travel behavior in two distinct ways: (a) analysis is done by considering travel time, mode choice, and departure time for work simultaneously, and (b) heterogeneity in behavior is accounted for using methods that identify different groups of behavior and then their determinants. Conclusively the method here is richer than many other methods used to study the ethnically diverse population of California and shows the addition of geographic location and latent segment identification to greatly improve our understanding of specific behaviors. It also provides evidence that immigrants are as diverse as the non-immigrant population and transportation policies need to be defined accordingly.

Effect of handling characteristics on minimum time cornering with torque vectoring

In this paper, the effect of both passive and actively-modified vehicle handling characteristics on minimum time manoeuvring for vehicles with 4-wheel torque vectoring (TV) capability is studied. First, a baseline optimal TV strategy is sought, independent of any causal control law. An optimal control problem (OCP) is initially formulated considering 4 independent wheel torque inputs, together with the steering angle rate, as the control variables. Using this formulation, the performance benefit using TV against an electric drive train with a fixed torque distribution, is demonstrated. The sensitivity of TV-controlled manoeuvre time to the passive understeer gradient of the vehicle is then studied. A second formulation of the OCP is introduced where a closed-loop TV controller is incorporated into the system dynamics of the OCP. This formulation allows the effect of actively modifying a vehicle's handling characteristic via TV on its minimum time cornering performance of the vehicle to be assessed. In particular, the effect of the target understeer gradient as the key tuning parameter of the literature-standard steady-state linear single-track model yaw rate reference is analysed.     

A tool to aid redesign of flexible transport services to increase efficiency in rural transport service provision

Rural areas generally have lower and more dispersed demands for travel which cannot sustain conventional public transport services and consequently have a greater number of flexible and demand responsive transport services operating. These services usually operate on a stand-alone basis, are often subsidized and are typically only accessible by certain passenger types or for specific trip purposes. This generally results in uncoordinated and inefficient transport provision overall. The Flexible integrated transport services (FITS) system featured in this paper has been designed to address this problem. FITS can be used as a planning tool to assess potential benefits from relaxing operating constraints (e.g., a service's operating boundaries), which can potentially suggest service redesign. It also includes the capacity to assign subsidy payments on a trip by trip basis to increase cost efficiency whilst meeting a greater proportion of transport needs. The case study in the paper focusses on transport to health in the Aberdeenshire and Morayshire areas of Scotland in the UK. Despite flexible transport operators receiving public funds to meet passenger needs, this is currently being supplemented by public bodies paying large amounts in taxi fares in instances where there is a statutory obligation to provide travel but where no other suitable transport service exists. The results demonstrate the potential substantial savings which could be realized by allowing transport operators to redesign their services by relaxing constraints and by the reassignment of subsidies: resulting in more passenger demands being met and a reduction in public spending on taxi fares.     

美国的城市交通规划

介绍了今后几十年中将影响城市交通规划的一些重要趋势，讨论了今后交通规划者在十个领域可能面临的挑战。