Development and Evaluation of Vehicle Simulation Models for a 4WS Application

In the scope of the European Prometheus project a passenger car with active rear wheel steering was developed by TNO in cooperation with PSA. During development and engineering of the rear wheel steering system simulation tools have been used to reduce development costs. This paper describes the evaluation of different simulation models, from simple to complex, with results of full vehicle driving tests. The optimal balance for model complexity and accuracy was achieved with a 2-dimensional model with an added roll degree of freedom. The results show that validation using time responses can give ambiguous and inaccurate results, and that frequency response functions are much more usable in validation.     

Some New Results in Rolling Contact

In the present paper three problems in the simplified theory of rolling contact are investigated. As to the first problem, three benchmark loadings, derived by Kalker in 1973 for Hertzian rollingcontact, are in existence. Each of these loadings gives rise to a value of the flexibility parameter of the simplified theory. These values are combined to a single, creepage dependent value of the flexibility, which appears to have an error of at most 10 to 15%. Secondly, the law of Coulomb is generalised by introducing two values of the coefficient of friction. The FASTSIM algorithm is adapted to that, and it is found that the traction, and hence the displacement, show a discontinuity inside the contact area. The discontinuity in the displacement is removed by introducing damping in the constitutive relations of the simplified theory. The damping constant is determined experimentally. When the damping coefficient decreases, the damped solution tends to the solution obtained directly without damping. This establishes the correctness of the latter, but it does not compare well with the complete theory as implemented by the program CONTACT. Thirdly and finally, it is shown that inertial effects may be neglected at speeds of around 100 km/h and also for much higher rolling velocities.     

Accelerated Service Life Testing of Automotive Vehicles on a Test Course

The accelerated service life testing of automotive vehicles for durability to road roughness induced dynamic loads is often accomplished in the laboratory using road roughness simulation facilities [1-5]. However, such tests can also be accomplished by a carefully designed field operation on a test course [6], where both the speed of the vehicle and the roughness of die test course become variables that control the degree of the test acceleration. Field tests are generally harder to control than laboratory tests, but offer a greater degree of realism since the vehicle is fully operational during the test exactly as it will be in service. This paper formulates the criteria for accelerated service life tests on a test course, evaluates the assumptions that must be enforced to obtain valid results, and explores the sensitivity of the results to the critical test parameters, namely, the vehicle speed and the road roughness severity of the test course relative to the service environment.     

预应力混凝土简支矮肋T梁桥应用研究

提出将预应力混凝土矮肋T梁应用于小跨径桥梁.以20 m跨径简支梁桥为例,对矮肋T梁截面效率,横隔板设置特点进行了分析,并采用解析法和空间有限元法进行横向分布系数分析计算.分析表明,矮肋T梁可应用于小跨径桥梁上部结构.     

Analysis of the performance of the evaporator of automotive air conditioning system

The purpose of this research was to establish a theoretical model for the evaporator of automotive air conditioning system and conducting simulations to evaluate the effect of operation parameters, environmental conditions, and design parameters on the performance of evaporator. An automotive air conditioning system primarily consists of four components: the compressor, the condenser, the refrigerant controller, and the evaporator. The refrigerant flow in the evaporator can be divided into two regions: the evaporating region and the superheat region. The refrigerant in the first region is a two-phase flow, while the refrigerant in the latter region is in the state of superheated vapor. The air flowing through the interior of the evaporator can also be divided into two zones: the unsaturated zone and the saturated zone. Water vapor is condensed in the saturated zone while in the unsaturated zone, no water condenses. Because the refrigerant flow and the airflow are perpendicular to each other, the distribution of refrigerant in the evaporating region and the superheat region does not coincide with the distribution of air in the unsaturated zone and the saturated zone. This study examines the effects of different design parameters, environmental conditions and operating parameters on the cooling capacity and superheat of an air conditioning system. Design parameters include the length of the refrigerant channel, the length of the air channel, and the thickness of the fins. Environmental conditions include the air inlet temperature and absolute humidity. Operation conditions include the refrigerant inlet enthalpy, inlet air flow rate, and refrigerant mass flow rate. Results of simulation demonstrated that fins with 50 micron meters width has the greatest cooling capacity for identical outer dimensions; thicker or thinner fins only decreased cooling capacity. Under different outer dimensions, longer refrigerant tubes and air channels created a greater cooling capacity. However, the increase in cooling capacity becomes less and less if the refrigerant flow was fixed because the heat transfer capability of the gaseous refrigerant was limited. In this study, an increase of 19% in cooling capacity can be reached as the length of refrigerant channels was increased, and the increased length of the air channels can promote the cooling capacity by 22%. Besides, it was found in this study that a decrease in the refrigerant inlet enthalpy, the inlet air flow rate, the air inlet temperature, and the inlet absolute humidity, or an increase in the refrigerant mass flow rate, would extend the superheat region and decrease the refrigerant’s superheat. It was also found that the cooling capacity of air conditioners is extremely sensitive to changes in the refrigerant mass flow rate and the inlet enthalpy, and variations more than 50% were found in the operating ranges examined in this study. However, changes in the inlet temperature, absolute humidity, and inlet air flow rate only resulted in variations between 10% and 20% in the examined ranges of conditions. Finally, a correlation among these variables and the simulated cooling capacity was obtained in this study, enabling the relevant researchers to evaluate automotive air conditioning performance under different environmental conditions and operation parameters more easily.     

Design of 2-speed transmission for electric commercial vehicle

As environmental and economic interests increase, the need for eco-friendly vehicle such as an electric vehicle (EV) has increased rapidly. Various research of enhancing EV powertrain efficiency and relibility have been studied. In this study, 2-speed shift gears mechanism is designed by using simpson type planetary gear train. This transmission has two planetary gear unit. Gear position is determinded by which ring gear is fixed. Internal components of the transmission are designed for satisfying the required specification of EV. We analyze gear strength, gear mesh efficiency, and transmission efficiency. By manufacturing the transmission prototype and performing some experiments, we verify the application suitability of this transmission.     

Experimental investigation of B20 combustion and emissions under various intake conditions for low-temperature combustion

Recently, biodiesel has emerged as an alternative fuel for achieving low-temperature combustion (LTC). Several articles in the literature have showed that oxygenated biofuels, including biodiesel, can improve combustion stability under high exhaust gas recirculation (EGR) operation, which is considered to be necessary for the removal of nitric oxides (NOx). The objective of this study was to investigate the performance and emissions of 20% biodiesel blended diesel fuel (B20) at various intake pressures and oxygen concentration levels to characterize the fuel for LTC application. The experimental investigation of B20 was carried out using a single-cylinder engine (SCE) at 1400 rpm and 50% load condition. A set of critical flow orifices with synthetic EGR was employed to simulate various intake pressures and EGR levels. The behavior of the B20 was first characterized under various intake conditions. The results showed that with high oxygen intake, B20 exhibited combustion and emission levels that were very similar to conventional diesel. However, B20 reduced combustion deterioration while exhibiting lower carbon monoxide (CO) and hydrocarbon (HC) emissions than diesel under low oxygen intake conditions.     

Nonlinear sliding mode observer for exhaust manifold pressure estimation in a light-duty diesel engine

In this paper, a sliding mode observer is proposed to estimate exhaust pressure for a diesel engine equipped with variable geometry turbocharger (VGT) and exhaust gas recirculation (EGR) systems. Since the exhaust pressure directly affects generation of the VGT power and the EGR rate in the cylinder, the exhaust pressure information is important for precise control of the VGT and EGR systems. In order to estimate the exhaust pressure accurately, a dynamic model of intake and exhaust pressure was derived. Furthermore, the mass flow rate and temperature of the air system in the diesel engines were modeled by consideration of physical phenomena and the thermodynamic law. Based on the developed models, a nonlinear sliding mode observer was designed to estimate the exhaust pressure. Convergence of the proposed observer was verified by the Lyapunov stability criterion. The proposed observer was implemented on a real-time embedded system and validated with the engine experiments. The experimental results show that the observer estimates the exhaust pressure accurately in both steady and transient engine operating conditions. Moreover, as a case study, the estimation results of the proposed observer could be applied for detecting a fault of the EGR system. The fault of the EGR system was detected precisely using the estimation result and the limited sensor information in mass-produced engines.     

Evaluation of safety benefits of automatic crash information notification systems on freeways

The automatic crash information notification system (ACINS) is an effective technology to enhance the potential for saving crash victims by reducing the crash response time (CRT) of emergency medical services. Shorter CRT results in a greater potential to save the lives and to alleviate the severity of injuries for crash victims. To fully operate the ACINS, reliable assessments of the safety benefits would be needed for justifying public investment. This study proposed a methodology for quantifying the effectiveness of the ACINS and applied the methodology to the Korean freeway system. The proposed methodology consists of three steps. The first step is to develop a statistical model for predicting injury severity of crash victims using ordered logistic regression. The second step is to estimate the amount of reduced CRT by applying ACINS. The effectiveness of the ACINS, which are defined as the number of reduced fatalities and severe injuries, were evaluated with the consideration of the market penetration rate (MPR) in third step. It has been found that approximately 9.4–15.4% of fatalities can be reduced with 100% MPR when the proposed methodology is applied to 2011 freeway crash data. The outcomes of this study support decision making for public investments and for establishing relevant traffic safety policies.