Simple design approach for improving characteristics of interior permanent magnet synchronous motors for electric air-conditioner systems in HEV

In this paper, a simple design method for improving the performance of an interior permanent magnet synchronous motor (IPMSM), for driving the air-conditioning compressor used in hybrid electric vehicles, is presented. There are many design methods that optimize the IPMSM. Each method deals with a variety of design factors, such as slot opening, pole arc, and rotor shape. However, as the number of design variables increases, a lot of modeling and analysis time is needed in order to improve the characteristics of an IPMSM. This paper demonstrates that the optimization of a double-layer IPMSM, satisfying the given design conditions, is possible with only a flux barrier shape design. Then, response surface methodology is applied as the optimization method, and the validity of the design approach is verified by comparison with test results.     

Simulation of HCCI combustion with spatial inhomogeneities via a locally deterministic approach

There has been recent interest in a new engine type, Homogeneous Charge Compression Ignition (HCCI), to combine the advantages of SI and CI engines. In this paper, a locally deterministic approach is employed to consider spatial inhomogeneities using the KIVA-CHEMKIN package. Validation is performed for two experimental HCCI engines fueled, respectively, by hydrogen and n-heptane. The full mechanism for hydrogen and a skeletal mechanism for n-heptane are used for combustion chemistry. Differences in the reaction flow paths are shown at ignition and the heat release reaction stages of the two fuels. Results show good agreement between measured and calculated pressures for different initial mixture temperatures with estimated residual fractions. A parametric study is performed in both engines to consider the influences of the physical parameters wall temperature, swirl ratio and global equivalence ratio. The ignition time of n-heptane is shown to be relatively insensitive to variations in these parametric due to its two-stage ignition behavior.     

“五星”中国造——奇瑞A3C-NCAP碰撞试验点评

一直以来,自主品牌轿车在C—NCAP的试验场上似乎总显得有些心有余而力不足,从没没和“五星”扯上什么关系。但最新一批公布的C—NCAP碰撞试验结果却让我们着实兴奋了一把,因为里面有一个非堂响亮的名字——奇瑞A3,它的响亮来自于它头上萦绕的“五星”光环。不错,奇瑞A3用自己的强势表现和最终的成绩向世界宣告,自主品牌也可以造出“五星级”的家用轿车。     

Multiple criteria evaluation of transportation system improvement projects: The case of korea

As a newly industrialized country, Korea has shown remarkable economic progress in the last three decades. This phenomenal growth has rapidly increased demands for better quality of life. This includes, among others, increasing demand for high quality transportation system services. In this paper, the method of Analytic Hierarchy Process (AHP) is utilized to evaluate rural highway improvement projects in Korea. The appropriate rural highway improvement projects for widening and paving were selected and studied on the basis of some selection criteria. The results have shown that there are some significant differences in prioritizing projects using the traditional economic evaluation method as compared to those resulting from the use of AHP. As demonstrated, the AHP proves to be an effective tool in evaluating transportation system projects.     

Flagging options for the future: A turning point in Korean shipping policy?

The issues surrounding the future of Korea's shipping policy have been heavily debated since 1990 because the Korean shipping industry has been facing rising crew costs and difficulties in recruitment of qualified crew, an adverse taxation system, very limited access to foreign capital markets, and an inflexible government regulatory environment. Consequently, this has contributed to the deterioration of Korea's compectitive edge. This paper aims to provide both an account of the current adverse situtation in Korean shipping business and proposals to alleviate the plight of shipping enterprises. Within the context of that adversity, two solutions are suggested to improve the current situation, by either establishing a Korean second register or flagging out. The paper explores the advantages and disadvantages of each solution. Because ship management is closely interrelated to flagging strategies, the paper also discusses areas of co-operation between Korean shipping or ship management companies and advanced foreign ship management companies.     

Measurement of soot oxidation with No<Subscript>2</Subscript>-O<Subscript>2</Subscript>-H<Subscript>2</Subscript>O in a flow reactor simulating diesel engine DPF

Understanding the mechanism of carbon oxidation is important for the successful modeling of diesel particulate filter regeneration. Characteristics of soot oxidation were investigated with carbon black (Printex-U). A flow reactor system that could simulate the condition of a diesel particulate filter and diesel exhaust gas was designed. Kinetic constants were derived and the reaction mechanisms were proposed using the experimental results and a simple reaction scheme, which approximated the overall oxidation process in TPO as well as CTO. From the experiments, the apparent activation energy for carbon oxidation with NO₂-O₂-H₂O was determined to be 40±2 kJ/mol, with the first order of carbon in the range of 10∼90% oxidation and a temperature range of 250∼500°C. This value was exceedingly lower than the activation energy of NO₂-O₂ oxidation, which was 60±3 kJ/mol. When NO₂ exists with O₂ and H₂O, the reaction rate increases in proportion to NO₂. It increases nonlinearly with O₂ or H₂O concentration when the other two oxidants are fixed.     

A study on slamming pressure on a flat stiffened plate considering fluid–structure interaction

Normally, the design slamming pressure on the bottomof a semi-submersible-type floating rig is determined in a simple way using the relative speed obtained from an air-gap analysis. However, few studies have taken a thorough, robust, and deep-background approach to the estimation of design pressure. To investigate the slamming pressure on the bottom of a semi-submersible rig, a simplified deformable stiffened plate of a zero-degree deadrise angle is simulated using the nonlinear FEM software LS-DYNA, which can take the influence of fluid–structure interaction (FSI) into account. Various parametric studies are carried out to examine the effects of structural flexibility, coupling stiffness, mesh size, velocity, stiffener size, and air cushion. The pressure response on the plate by the coupling of fluid and structure is studied and the FSI effect of each parameter is discussed. Then, equivalent transient and static loads that result in the same maximum or permanent deformation as FSI are evaluated for design purposes through a series of parametric studies.     

Influence of nozzle hole diameter and orifice diameter on dme spray to get the similar heat value with diesel spray using the constant volume chamber

Low heating value (LHV) of di-methyl ether (DME) is lower than that of diesel. To get the similar heat value with diesel from the diesel engine operation, single injection quantity of DME should be increased. This investigation was tried to increase the injection quantity of DME by the modified diesel injector and investigated the penetration length and spray angle of DME spray. DME was injected by using three-type modified diesel injectors those nozzle-hole diameters (Injector 1: 1.66 mm, Injector 2 and 3: 0.25 mm) and orifice diameters were different (Injector 1 and 2: 0.6 mm, Injector 3: 1 mm). Spray characteristics of DME was investigated with a various ambient pressures (2.5, 5.0 MPa) in the constant volume chamber and a fuel was injected by varied injection pressure from 35 to 70 MPa by interval of 5 MPa using a DME common rail fuel injection system. The result shows that DME injection quantity by Injector 3 was 1.69 ~ 2.02 times larger than that of diesel injection quantity by Injector 1. In this case, DME spray got the similar heat value compared with diesel spray. The penetration speed of DME spray by Injector 3 was the fastest, thus when the spray development was end, the penetration length of DME spray by Injector 3 was the longest compared with the other cases. In case of the spray angle, Injector 2 and 3 had the similar spray angle and these were larger than that of diesel and DME sprays by Injector 1. As the result, Injector 3 was the solution for how to solve the low heating value of DME.     

Development of jacket platform tsunami risk rating system in waters offshore North Borneo

This work details the simulation of tsunami waves generated by seaquakes in the Manila Trench and their effect on fixed oil and gas jacket platforms in waters offshore North Borneo. For this study, a four-leg living quarter jacket platform located in a water depth of 63m is modelled in SACS v5.3. Malaysia has traditionally been perceived to be safe from the hazards of earthquakes and tsunamis. Local design practices tend to neglect tsunami waves and include no such provisions. In 2004, a 9.3M _w seaquake occurred off the northwest coast of Aceh, which generated tsunami waves that caused destruction in Malaysia totalling US$ 25 million and 68 deaths. This event prompted an awareness of the need to study the reliability of fixed offshore platforms scattered throughout Malaysian waters. In this paper, we present a review of research on the seismicity of the Manila Trench, which is perceived to be high risk for Southeast Asia. From the tsunami numerical model TUNA-M2, we extract computer-simulated tsunami waves at prescribed grid points in the vicinity of the platforms in the region. Using wave heights as input, we simulate the tsunami using SACS v5.3 structural analysis software of offshore platforms, which is widely accepted by the industry. We employ the nonlinear solitary wave theory in our tsunami loading calculations for the platforms, and formulate a platform-specific risk quantification system. We then perform an intensive structural sensitivity analysis and derive a corresponding platform-specific risk rating model.     

Activity space estimation with longitudinal observations of social media data

In this paper, we demonstrate the use of an inexpensive and easy-to-collect long-term dataset to address the problems caused by basing activity space studies off short-term data. In total, we use 63,114 geo-tagged tweets from 116 unique users to create individuals’ activity spaces based on minimum bounding geometry (convex hull). By using polygon density maps of activity space, we found clear differences between weekday and weekend activity spaces, and were able to observe the growth trajectory of activity space over 17 weeks. In order to reflect the heterogeneous nature of spatial behavior and tweeting habits, we used Latent Class Analysis twice. First, to identify five unique patterns of location-based activity spaces that are different in shape and anchoring. Second, we identify three unique growth trajectories. The comparison among these latent growth trajectories shows that in order to capture the extent of activity spaces we need long time periods for some individuals and shorter periods of observation for others. We also show that past studies using a single digit number of weeks may not be sufficient to capture individuals’ activity space. The major activity locations identified using a multilevel latent class model, do not appear to be statistically related to the growth patterns of Twitter users activity spaces. The evidence here shows Twitter data can be a valuable complementary source of information for heterogeneity analysis in activity-based modeling and simulation.