Operating speed pattern optimization of railway vehicles with differential evolution algorithm

The railway transportation system has much advantage in eco-friendliness, punctuality and safety compared to any other transportation system. Most of the railway system administrators have to control and operate under limited resources such as trains and facilities. It is necessary to control traveling time and energy consumption for efficient operation in the railway systems, because the board rate of passenger is inconstant with time variance. It is common that the shorter traveling time causes the greater energy consumption. In this study, a new optimization method considering operation time or energy consumption is proposed by using differential evolution algorithm and some cases are reviewed. The total energy change due to operation time variation are investigated by using the proposed optimization method for tangent and gradient track conditions. Both cases, the total energy decreases exponentially. However, because of gradient the total energy are saturated after a certain time for gradient track.     

Crash protection of Hybrid Electrical Vehicles for amending the KMVSS No. 91

This paper explores issues related to the electrical safety of Hybrid Electrical Vehicles (HEVs) during and after various crash events. Japanese and American federal regulations regarding occupant protection against high voltages in Electric Vehicles (EVs) and HEVs were surveyed and analyzed in this study. Front, side and rear impact tests for two types of HEVs were conducted to investigate electrolyte spillage, the retention of the propulsion battery system and the electrical isolation of the occupant. The test results met the related criteria. The test procedures and the criteria for occupant protection established through this study were amended to Korean Motor Vehicle Safety Standard (KMVSS) No. 91 to add the crash protection of the EVs and the HEVs.     

Comparison of the optimum designs of center pillar assembly of an auto-body between conventional steel and ahss with a simplified side impact analysis

This study compares the optimum designs of center pillar assembly with advanced high-strength steel (AHSS) to that of conventional steel for crashworthiness and weight reduction in side impacts. A simplified side impact analysis method was used to simulate the crash behavior of the center pillar assembly with efficient computing time. Thickness optimization aims to perform an S-shaped deformation of the center pillar toward the cabin to reduce the injury level of a driver in a crash test. Center pillar members were regarded as an assembly of parts that are fabricated with tailor-welded blanks, and the thickness of each part was selected as a design variable. The thickness variables of parts that have significant effects on the deformation mechanism were extracted as the main design variables for thickness optimization based on the results of a sensitivity analysis with design of experiments. The optimization condition was constructed to induce an S-shaped deformation mode and reduce the weight of the center pillar assembly. An optimum design was obtained after several iterations with response surface methodology (RSM). Optimization was first performed with conventional steel and then with AHSS with the same procedure to optimize the crashworthiness of the center pillar assembly. After thickness optimization, optimum designs were applied to the full vehicle analysis to evaluate the validity of the optimization scheme with the simplified side impact analysis method. Then, the crashworthiness of optimum designs with conventional steel and AHSS were compared using the full vehicle analysis. This comparison demonstrates that AHSS can be more effectively utilized than conventional steel to obtain a lightweight design of an auto-body with enhanced crashworthiness.     

Major sources of hydrocarbon emissions in a premixed charge compression ignition engine

Although premixed charge compression ignition (PCCI) combustion engines are praised for potentially high efficiency and clean exhaust, experimental engines built to date emit more hydrocarbons (HCs) and carbon monoxide (CO) than the conventional machines. These compounds are not only strictly controlled components of the exhaust gas of road vehicles but are also an energy loss indicator. The prime objective of this study was to investigate the major sources of the HCs formed in the combustion chamber of an experimental PCCI engine in order to suggest some effective technologies for HC reduction. In this study, to explore the dominant sources of HC emissions in both operation modes, a single cylinder engine was prepared such that it could operate using either conventional diesel combustion or PCCI combustion. Specifically, the contributions of the top-ring crevice volume in the combustion chamber and the bulk quenching of the lean mixture were investigated. To understand the influence of the shape and magnitude of the crevice on HC emissions, the engine was operated with 12 specially prepared pistons with different top-ring crevices installed one after another. The engine emitted proportionally more HCs as the depth of the crevice increased as long as the width remained narrower than the prevailing quench distance. The top-ring-crevice-originated exhaust HCs comprised approximately 31% of the total HC emissions in the baseline condition. In a series of tests to estimate the effects of bulk quench on exhaust HC emissions, intake air was heated from 300K to 400K in steps of 25K. With the intake air heated, HC and CO emissions decreased with a gradually diminishing rate to zero at 375K. In conclusion, the most dominant sources of HC emissions in PCCI engines were the crevice volumes in the combustion chamber and the bulk quenching of the lean mixtures. The key methods for reducing HC emissions in PCCI engines are minimizing crevice volume in the combustion chamber and maximizing intake air temperature allowed based on the permissible NOx level.     

Improving the predictiveness of the quasi-d combustion model for spark ignition engines with flexible intake systems

Fast and predictive simulation tools are prerequisites for pursuing simulation based engine control development. A particularly attractive tradeoff between speed and fidelity is achieved with a co-simulation approach that marries a commercial gas dynamic code WAVE™ with an in-house quasi-dimensional combustion model. Gas dynamics are critical for predicting the effect of wave action in intake and exhaust systems, while the quasi-D turbulent flame entrainment model provides sensitivity to variations of composition and turbulence in the cylinder. This paper proposes a calibration procedure for such a tool that maximizes its range of validity and therefore achieves a fully predictive combustion model for the analysis of a high degree of freedom (HDOF) engines. Inclusion of a charge motion control device in the intake runner presented a particular challenge, since anything altering the flow upstream of the intake valve remains “invisible” to the zero-D turbulence model applied to the cylinder control volume. The solution is based on the use of turbulence multiplier and scheduling of its value. Consequently, proposed calibration procedure considers two scalar variables (dissipation constant C _β and turbulence multiplier C _M ), and the refinements of flame front area maps to capture details of the spark-plug design, i.e. the actual distance between the spark and the surface of the cylinder head. The procedure is demonstrated using an SI engine system with dual-independent cam phasing and charge motion control valves (CMCV) in the intake runner. A limited number of iterations led to convergence, thanks to a small number of adjustable constants. After calibrating constants at the reference operating point, the predictions are validated for a range of engine speeds, loads and residual fractions.     

Model-based design of a variable nozzle turbocharger controller

Variable Nozzle Turbocharger (VNT) was invented to solve the problem of matching an ordinary turbocharger with an engine. VNT can harness exhaust energy more efficiently, enhance intake airflow response and reduce engine emissions, especially during transient operating conditions. The difficulty of VNT control lies in how to regulate the position of the nozzle at different engine working conditions. The control strategy designed in this study is a combination of a closed-loop feedback controller and an open-loop feed-forward controller. The gain-scheduled proportional-integral-derivative (PID) controller was implemented as the feedback controller to overcome the nonlinear characteristic. As it is difficult to tune the parameters of the gain-scheduled PID controller on an engine test bench, system identification was used to identify the plant model properties at different working points for a WP10 diesel engine on the test bench. The PID controller parameters were calculated based on the identified first-order-plus-dead-time (FOPDT) plant model. The joint simulation of the controller and the plant model was performed in Matlab/Simulink. The time-domain and frequency-domain performances of the entire system were evaluated. The designed VNT control system was verified with engine tests. The results indicated that the real boosting pressure traced the target boosting pressure well at different working conditions.     

Modified lateral control of an autonomous vehicle by look-ahead and look-down sensing

This paper presents a modified lateral control method for an autonomous vehicle with both look-ahead and look-down sensing systems. To cope with sensor noise and modeling uncertainty in the lateral control of the vehicle, a modified LMI-based H lateral controller was proposed, which uses the look-ahead information of the lateral offset error measured at the front of vehicle and the look-down information of the vehicle yaw angle error between the reference lane and the centerline of the vehicle. To verify the safety and the performance of the lateral control, a scaled-down vehicle was developed, and the positioning of the vehicle was estimated with USAT. The proposed controller, which uses both look-ahead and look-down information, was tested for lane changing and reference lane tracking with both simulation and experiment. The simulation and experimental results show that the proposed controller has better tracking and handling performance compared with a controller that uses only the look-ahead information of the target heading angle error.     

Finite element modeling of static tire enveloping characteristics

To investigate static tire enveloping characteristics, a three dimensional (3-D) finite element model is proposed. The vertical stiffness of the tire is studied on a flat surface with and without cleat. Tire rubber materials and cord layers are represented independently using “rebar” elements available in MSC Marc Mentat. Comparisons of numerical and experimental results are given to show the validity of the proposed model. It is shown that after a certain displacement, the results of the proposed model agree well with experimental results. In addition, the model results show that regardless of the type of the cleat placed under the rim center (hub center), all vertical force curves intersect after a certain displacement, which indicates typical static enveloping characteristics. Moreover, another typical characteristic of the radial tires that is unlike those of bias-ply constructions confirms that the contact patch does not expand laterally after a level vertical load is applied to the tire, which is directly related to fuel consumption and tire tread life.     

Development of hot stamped center pillar using form die with channel type indirect blank holder

The hot stamping process has been used in the automotive industry to reduce the weight of the body-in-white and to increase passenger safety via improved crashworthiness. However, defects such as fracture and wrinkle occur when hot stamping is performed using a conventional drawing or forming method. In this study, a channel-type indirect blank holder (CIBH) is proposed to develop a high-strength center pillar in form-type hot stamping, so that the aforementioned drawbacks are overcome. This type of blank holder plays an important role in reducing severe wrinkling at the flange; such wrinkling leads to folding after the completion of form-type hot-stamping. First, we investigated the effect of the channel shape on the indirect blank holding force by using a simplified two-dimensional plane-strain stamping process. Second, we selected the slope angle and corner radius of the channel as the main shape parameters by finite element analysis and artificial neural network (ANN). It is known that fracture at the hot formed wall and wrinkle at the flange are significantly affected by the slope angle of the channel, and the appropriate value for eliminating fracture and wrinkle is determined to be 99°. By performing hot stamping using a form die with the selected channel, we can manufacture a high-strength center pillar without wrinkle and fracture.