铁路隔震连续梁桥地震碰撞响应研究

在地震作用下隔震桥梁的梁体位移比非隔震桥梁明显增加,使得相邻梁发生碰撞的概率增大。以1联3跨铁路隔震连续梁桥为例,选用3条人工地震波,采用非线性时程分析方法进行该桥的碰撞响应分析,研究梁间伸缩缝宽度和隔震支座刚度对梁间碰撞响应的影响。结果表明:随着伸缩缝宽度的增大和隔震支座刚度的增大,相邻梁碰撞的发生次数和碰撞力均有明显减小;地震作用下隔震固定墩墩底最大弯矩和最大剪力均随着隔震支座刚度的增加而增加。因此,在进行隔震桥梁设计时,应综合考虑隔震支座的隔震效果和碰撞响应,从而得到既经济又安全的隔震桥梁设计参数。     

Research on the Influence of Vertical Deformation of Bridge on the Track RegularityEI北大核心

Research purposes: The vertical deformation of high-speed railway (HSR) bridge will cause the track irregularity, which threatens the safe and efficient operation of the HSR. Taking the 32 m simple supported beam bridge as the research object, based on the existing mapping analytical model for bridge vertical deformation and rail geometry, the influence of the track regularity of the CRTS Ⅰ slab ballastless track structure caused by the key parameters such as the bridge vertical deformation amplitude, the hanging length of the beam end and the vertical stiffness of mortar layer were studied, and the corresponding measures to control the rail deformation were proposed, to provide theoretical reference for comprehensive treatment of rail deformation of HSR bridge. Research conclusions:(1) The pier settlement, the vertical rotation of the beam end and the beam fault will cause the rail to follow the beam deformation, and "up-warping" of the rail on the vertical deformation boundary will appear. (2) The rail deformation is directly proportional to the vertical deformation amplitude of the bridge and the key to control the rail deformation is to reduce the vertical deformation of the bridge. (3) The rail deformation can be controlled by reducing the hanging length of beam and vertical stiffness of mortar layer. (4) The research results can provide a theoretical reference for controlling the vertical rail deformation of high-speed railway bridges. © 2018, Editorial Department of Journal of Railway Engineering Society. All right reserved.     

The Reinforcement Analysis of Prestressed Anchor Frame Beam in the Deep Cutting Slope under Three Dimensional Strong EarthquakeEI北大核心

Research purposes: In order to further study the reinforcement of prestressed anchor frame beam in the deep cutting slope under three dimensional strong earthquake, a model of the deep cutting slope is built through FLAC 3D simulation software, the seismic wave to the model from three directions of x,y and z is input, and the dynamic response of the slope is analyzed. Then, the prestressed anchor frame beam reinforcement measures are applied to the model, and this paper analyzes the reinforcement effect of the prestressed anchor frame beam to the deep cutting slope under three dimensional strong earthquake. Research conclusions:(1) The prestressed anchor frame beam has a good effect on restraining the horizontal displacement of the deep cutting slope. (2) Under the three dimensional strong earthquake, the prestressed anchor frame beam has a good effect on the horizontal acceleration and horizontal velocity of the deep cutting slope, which reduces the peak of horizontal acceleration and horizontal velocity. (3) Through the comparison of the response before and after the reinforcement of the prestressed anchor frame beam is given under the 9 degrees three dimensional strong earthquake, it can be concluded that the prestressed anchor frame beam can provide good reinforcement effect to the deep cutting slope. (4) This research can be used for reference to the earthquake resistance of the slope engineering. © 2018, Editorial Department of Journal of Railway Engineering Society. All right reserved.     

曲线对高速货车转向架焊接部件疲劳损伤的影响

依据UIC510—3:1994规定的疲劳试验加载方法,基于有限元法研究了不同左右曲线变换次数取值时高速货车转向架焊接构架及摇枕疲劳关注部位累积损伤的变化程度及规律。仿真结果及综合分析表明,当左右曲线变换次数取值变化并不十分显著时,其对结构疲劳损伤影响很小,样机疲劳试验中可直接应用UIC规范中的建议值。     

JC型弹性旁承体安装时侧翼橡胶层应力分析

对目前货车转向架装用的JC型双作用弹性旁承体进行了非线性有限元计算,分析了旁承体两侧翼橡胶层在安装及工作时的应力,给出了JC型双作用弹性旁承体在安装时的相关建议。     

出口马达加斯加米轨转向架的研制

介绍了出口马达加斯加米轨转向架的主要技术参数、结构特点及有关计算和试验情况.     

主动导向转向架的多体动力学仿真与试验研究

对主动导向转向架的半车模型进行了多体动力学计算,并进行了滚动台试验,计算结果和试验结果基本一致。将半车模型扩展为整车模型后,进行了计算分析,研究结果表明,主动导向转向架可以大大提高转向架的曲线通过性能。     

牵引变电所换相连接方式研究

针对石家庄西变电所施工改造中,2008年3月发生的变电所母线和变压器换相连接问题,利用理论和测试的方法进行了分析,找出了原因。同时结合运行和施工中其他2例换相故障,提出了几项切实可行的措施。     

富水砂层盾构始发井防涌水检测与加固

基于广州地铁6号线大坦沙站盾构始发井的实践,研究富水砂层中破除盾构井端头门时防涌水的施工监测和工程检测方法,根据检测和监测结果,基于朗金土压力理论进行计算分析,提出相应的加固措施和方法。介绍了具体的防水加固措施和效果。     

激光堆焊工艺在修造领域的应用现状及发展趋势

本文详细阐述了激光堆焊工艺在工业修造领域的应用现状及发展趋势,介绍了激光束的能源、输送和聚焦系统、堆焊材料及激光设备。重点说明了其在修造领域的应用工艺。