荷坳隧道四洞小净距段支护结构设计研究北大核心CSCD

多洞空间小净距隧道支护结构参数量化设计与安全性分析是当前设计中的一大难题。文章针对深圳机荷高速公路荷坳隧道四洞小净距段的设计,采用总安全系数法对四洞的开挖与支护模式、各洞的开挖顺序及支护参数进行了研究比较,并采用隧规荷载-结构法、增量法、地层-结构法对支护结构的安全系数进行了对比计算,得出以下结论:(1)提出了基于总安全系数法原理的多洞空间小净距隧道设计方法;(2)根据总安全系数法得出了荷坳隧道四洞小净距段应采用“先行洞二次衬砌完成后再开挖下一孔隧道”的开挖与支护模式,且应按洞1→洞2→洞3→洞4的开挖顺序施工;(3)隧规荷载-结构法、增量法、地层-结构法虽无法得出结构的总承载安全系数,但在一定程度上可以反应部分支护结构的安全性。     

基于纸纤维改性的隧道工程透水砂浆性能研究北大核心CSCD

为提出一种适用于隧道初期支护基面找平并且具有一定透水性能的砂浆,将纸纤维加入砂浆试块中对其性能进行改性。通过分析纸纤维的降解原理,并将不同掺量的纸纤维加入砂浆试块中,对其体积密度、吸水率、抗压强度等基本性能指标及微观结构进行测试和分析。由试验结果可知:在碱性环境中,纸纤维具有可降解的性能特点;纸纤维可以使普通砂浆试块的吸水率提升2~3倍,同时也会造成砂浆试块的体积密度和抗压强度降低;对砂浆试块吸水率和抗压强度进行线性拟合后发现其吸水率和抗压强度呈现负相关关系。研究结果表明,通过纸纤维对砂浆进行透水性能的提升是可行的,但是纸纤维掺量对砂浆其他性能的影响还有待进一步研究。     

Analysis on Ground Surface Deformation and Influence of Construction Parameters Caused by Two Different Shield Machines in Double-tube Tunnelling北大核心CSCD

Based on a shield-driven running tunnel project of Hangzhou Metro Line 2, this paper carries out field measuring of the ground surface deformation caused by two different shield machines in double-tube tunnelling in soft soil areas, obtains the laws of the surface deformation caused by shield-driven double-tube tunnelling and verifies the applicability of the modified Peck formula to double-tube tunnelling. The results show that in soft soil areas the impacts on ground surface deformation caused by different shield construction parameters in the previously and subsequently excavated tunnels are different, while the surface deformation changes sharply before and after the shield machine passing through the cutting face, and a rebound phenomenon occurs when the shield tail passes through the cutting face due to the influence of the grouting; The cutterhead torque of the shield machine in soft soil areas can be composed of five calculation factors, and the calculation results are in good agreement with the measured values. The larger the opening rate of the shield cutterhead is, the larger the average torque value will be, the higher the percentage of large ground loss rate will be, and the larger the maximum ground surface settlement will be; The ratio of cutterhead torque T to mucking volume per ring Q is used as the control parameter for analyzing the ground surface settlement, and a certain positive correlation between the ratio and the surface settlement value is determined, the smaller the cutterhead opening rate is, the more accurate the fitting results will be. © 2022, Editorial Office of Modern Tunnelling Technology. All right reserved.     

大跨径连续刚构桥的温度效应分析

以魏家洲特大桥为例,按照我国公路桥涵设计规范、英国BS5400规范、新西兰规范确定不同的计算模式,对大跨径连续刚构桥进行温度效应分析,得出：温度应力在大跨径连续刚构桥整个桥梁设计中占有很大的比重,且采用不同的温度梯度计算模式,所得到的梁内温度应力值相差较大,甚至出现异号的温度应力.     

间歇式沥青混凝土搅拌设备验收方法的确定

沥青搅拌设备整机验收一般应针对主要作业性能指标进行。科学合理地确定验收项目及验收依据是验收工作的关键，根据实践经验，提出了一套切实有效的验收方法。     

Evasive manoeuvres with a steering robot

In the pursuit of an objective rating on vehicle stability performance, it is always desirable to reduce disturbances and inconsistencies during experimental evaluations, especially the ones introduced by human drivers. This paper presents the development of a steering robot designed for closed-loop steering tasks during evasive manoeuvres. It describes the controller structure and discusses experimental results, in addition to simulation/vehicle model verifications and theoretical control analysis.     

Wheel-rail contact models for vehicle system dynamics including multi-point contact

Advanced modelling of rail vehicle dynamics requires realistic solutions of contact problems for wheels and rails that are able to describe contact singularities, encountered for wheels and rails. The basic singularities demonstrate themselves as double and multiple contact patches. The solutions of the contact problems have to be known practically in each step of the numerical integration of the differential equations of the model. The existing fast, approximate methods of solution to achieve this goal have been outlined. One way to do this is to replace a multi-point contact by a set of ellipses. The other methods are based on so-called virtual penetration. They allow calculating the non-elliptical, multiple contact patches and creep forces online, during integration of the model. This allows nearly real-time simulations. The methods are valid and applicable for so-called quasi-Hertzian cases, when the contact conditions do not deviate much from the assumptions of the Hertz theory. It is believed that it is worthwhile to use them in other cases too.     

Fuzzy-logic applied to yaw moment control for vehicle stability

In this paper, we propose a new yaw moment control based on fuzzy logic to improve vehicle handling and stability. The advantages of fuzzy methods are their simplicity and their good performance in controlling non-linear systems. The developed controller generates the suitable yaw moment which is obtained from the difference of the brake forces between the front wheels so that the vehicle follows the target values of the yaw rate and the sideslip angle. The simulation results show the effectiveness of the proposed control method when the vehicle is subjected to different cornering steering manoeuvres such as change line and J-turn under different driving conditions (dry road and snow-covered).