The Available Methods to Calculate the Wheel/Rail Forces in Non Hertzian Contact Patches and Rail Damaging

In the present paper, the methods used in railway dynamics to take into account the non Hertzian multi contact patches occurring on a wheel, are summarised. Some application cases are presented as well as an explanation of the so called “squat” rail deterioration.     

Testing and Analysis Techniques for Safety Assessment of Rail Vehicles: The State-of-the-Art

The methods currently being used in North America, Britain and Europe for the safety assessment of rail vehicles are discussed. There is considerable disparity between the methods that have been developed in the different countries. These differences, and the possible reasons for them, are discussed in the paper. Finally, conclusions are drawn and some recommendations are made for the future direction of safety assessment methods.     

Aerodynamic design optimization of rear body shapes of a sedan for drag reduction

This study proposes an aerodynamically optimized outer shape of a sedan by using an Artificial Neural Network (ANN), which focused on modifying the rear body shapes of the sedan. To determine the optimization variables, the unsteady flow field around the sedan driving at very fast speeds was analyzed by CFD simulation, and fluctuations of the drag coefficient (C _D ) and pressure around the car were calculated. After consideration of the baseline result of CFD, 6 local parts from the end of the sedan were chosen as the design variables for optimization. Moreover, an ANN approximation model was established with 64 experimental points generated by the D-optimal methodology. As a result, an aerodynamically optimized shape for the rear end of the sedan in which the aerodynamic performance is improved by about 5.64% when compared to the baseline vehicle is proposed. Finally, it is expected that within the accepted range of shape modifications for a rear body, the aerodynamic performance of a sedan can be enhanced so that the fuel efficiency of the sedan can be improved. The YF SONATA, a sedan manufactured by Hyundai Motors Corporate, played a major role in this research as the baseline vehicle.     

A self-powering system based on tire deformation during driving

Tire intelligence is vital in the improvement of the safety of vehicles because the tire supports the car body and is the contact point between the vehicle and the road. To create an intelligent tire, sensors must be installed to measure the behavior of the tire. However, it is difficult to apply a wired sensor system on the wheel of the tire. Hence, it is necessary to implement a self-powering, wireless system (a type of energy harvesting system) that can be mounted inside the tire. The purpose of this study is to convert the strain energy caused by deformation of the tire while driving into useful electrical energy to supply the sensor system. A flexible piezofiber is utilized for the energy conversion. The variation in strain, due to changes in speed, load, and the internal pressure of the tire, was measured along two axial directions to evaluate the amount of available strain energy. The amount of strain changed from 0.15% to 0.8%. To predict the amount of available energy from a tire, we perform an analysis of the relationship between the strain and the voltage. In addition, experiments for impedance matching between piezofiber and related circuits were conducted to optimize the external loads for transferring energy efficiently. Based on the procedure mentioned above, at least 0.58 mJ of electrical energy can be generated by using the laterally oriented strain (1500 to 2500 micro strain). The result of this study is expected to enhance the potential realization of self-generating wireless sensor systems for so-called ??intelligent?? tires.     

High-strain-rate fracture of adhesively bonded composite joints in DCB and TDCB specimens

Double-cantilever beam (DCB) and tapered double-cantilever beam (TDCB) specimens are the test configurations most commonly used to measure the fracture toughness of composites and adhesive joints. Strain rates of 1 to 18.47 m/s were applied to the test specimens via high-speed hydraulic test equipment. Because the fracture occurs through the adhesively bonded joints and the cracks grow rapidly, the crack length and beam displacement were recorded by a high-speed camera. An energy range from 0 to 10 J was often observed in the high-strain-rate fracture experiments for nonlinear plastic behavior of the dynamically loaded adhesively bonded DCB and TDCB specimens. The range of energy release rates (fracture energy) for TDCB specimen was 2 to 3 times higher than that of a DCB specimen for all high strain rates. The fracture energy of automotive adhesive joints can be estimated using the experimental results in this study for the fracture toughness (G_IC) under high rates of loading. The crack grows as the applied fracture energy exceeds the value of the critical energy release rate (G_IC) at the crack tip. The energy release rate was calculated using the fracture mechanics formula. The key fracture mechanics parameter, the fracture energy GIC, was ascertained as a function of the test rate and can be used to assess and model the overall joint performance.     

New lead-acid battery management system based on generator regulation

A novel regulation system for a vehicle generator and lead-acid battery is proposed in this paper. By integrating the regulation method, the output voltage of the generator is determined and controlled by the algorithm to save electrical energy and protect the lead-acid battery. The regulation algorithm is implemented in Matlab/Simulink, and the logic function of the system is verified using the dSPACE/AutoBox workbench. The experimental results show that the new algorithm improves the performance of the fuel economy of the vehicle and the battery state-of-health compared to the traditional control method.     

Prediction of the dimensional deformation of the addendum and dedendum after the warm shrink fitting process using a correction coefficient

The warm shrink fitting process is generally used to assemble automobile transmission parts (shafts/gears). However, this process causes a deformation in the addendum and dedendum of the gear depending on the fitting interference and gear profile, and this deformation causes additional noise and vibration between the gears. To address these problems, the warm shrink fitting process is analyzed by considering the error in the dimensional deformation of the addendum and dedendum found when comparing the results of a theoretical analysis and finite element analysis (FEA). A correction coefficient that reduces this error is derived through an analysis of the difference in the cross-sectional area between the shapes used for the theoretical analysis and that of the actual gear, and a closed-form equation to predict the dimensional deformation of the addendum and dedendum is proposed. The FEA method is proposed to analyze the thermal-structural-thermal coupled field analysis of the warm shrink fitting process (heating-fitting-cooling process). To verify the closed-form equation using the correction coefficient, measurements are made of actual helical gears used in automobile transmissions. The results are in good agreement with those given by the closed-form equation.     

Air transport and economic growth: a review of the impact mechanism and causal relationships

ABSTRACT

The impacts of air transport on the economy arise both directly, via activity in the aviation sector; and indirectly, via increased spending and wider economic benefits associated with improved access to resources, markets, technology and economic mass. Economic activity, in turn, supports and generates demand for air transport. Despite its potential importance, the reciprocal nature of the causal relationship between air transport and economic performance has remained somewhat understudied. This paper provides a synthesis review of the channels the aviation sector interacts with regional economy. The review focuses on quantitative studies that contribute to the state-of-the-art understandings of the causality. We find that the reciprocal causal relationship is more likely to prevail in less developed economies. For more developed economies, only one direction of the causality is recognised, which runs from air transport to economic growth. Especially substantial is the effect of airline enplanement on service-related employment. The reverse direction of the relationship is, however, not as significant as believed in a causal sense within the developed world. Therefore, cautions need to be taken when applying income elasticities (such as the elasticity of air passenger demand with respect to GDP) in air travel demand forecasting, which implicitly assumes that economic growth causally leads to air traffic increment. Based on the fundamental links between air transport and economic growth, some typical imperfections and inefficiencies in aviation markets are discussed and promising avenues for future research are proposed.     

Investigating the capacity of continuous household travel surveys in capturing the temporal rhythms of travel demand

Transportation - Continuous household travel surveys have been identified as a potential replacement for traditional one-off cross-sectional surveys. Many regions around the world have either...