Reaction characteristics of the diesel oxidation catalyst of particulate matters from the diffusion flame of a oiler burner

The objective of this experimental study is to investigate the characteristics of the size distribution and the number concentration of PM (particulate matters) emitted from the diffusion flame of a boiler burner, which has the same type of combustion as a diesel engine. This study is performed to investigate the emission characteristics of nanoparticles generated from diffusion combustion in diesel fuel, and it considered fuel factors and the reaction characteristics of the nanoparticles on the DOC (Diesel oxidation catalyst). The factors examined in this experiment included the sulfur content in the fuel, the blend of the diesel fuel containing biodiesel and bio-ethanol, and the concentration of engine oil (0.1% and 1.0%) blended with diesel fuel. The particle size distribution of the nanoparticles exhausted from the boiler burner was measured by an SMPS (scanning mobility particle sizer). The number concentration of PM that were smaller than 70 nm in diameter greatly increased in the rear of the DOC when fuel containing 250 ppm of sulfur was used. The experiment also suggested that the particle number concentration in both the front and rear of the DOC was lower when ULSD (ultra low sulfur diesel) fuel blended with biodiesel and bio-ethanol, which are oxygenated fuels, was used than when only ULSD fuel was used. The higher the content of engine oil in the fuel, the higher the particle number concentration was in the front and rear of the catalyst. When the first dilution air temperature is increased from 30°C to 180°C, the nanoparticle number concentration dramatically dropped in the rear of the catalyst when fuel containing 250 ppm of sulfur was used, while the particle size distribution remained almost the same when the fuel with engine oil was used.     

PSO algorithm-based parameter optimization for HEV powertrain and its control strategy

The coordination between the powertrain and control strategy has significant impacts on the operating performance of hybrid electric vehicles (HEVs). A comprehensive methodology based on Particle Swarm Optimization (PSO) is presented in this paper to achieve parameter optimization for both the powertrain and the control strategy, with the aim of reducing fuel consumption, exhaust emissions, and manufacturing costs of the HEV. The original multi-objective optimization problem is converted into a single-objective problem with a goal-attainment method, and the principal parameters of powertrain and control strategy are set as the optimized variables by PSO, with the dynamic performance index of HEVs being defined as the constraint condition. Computer simulations were carried out, which showed that the PSO scheme gives preferable results in comparison to the ADVISOR method. Therefore, fuel consumption and exhaust emissions of HEVs can be effectively reduced without sacrificing dynamic performance of HEVs.     

Benefits and challenges of controlling a LED AFS (adaptive front-lighting system) using fuzzy logic

The vehicular illumination system has undergone considerable technological advances in recent decades such as the use of a Light Emitting Diode (LED) Adaptive Front-lighting System (AFS), which represents an industry breakthrough in lighting technology and is rapidly becoming one of the most important innovative technologies around the world in the lighting community. This paper presents AFS control alternatives using fuzzy logic (types 1 and 2) to determine its operating parameters taking into consideration the road conditions in the state of São Paulo (Brazil). Fuzzy logic is a well-known extension of the conventional (Boolean) logic that enables the treatment of uncertainty present in the information through the definition of intermediary membership values between the “completely true” and the “completely false”. This technique or modeling strategy is particularly important when a multi-parameter decision must be taken or the decisions are based on the human knowledge. The results show the potential of the methodology proposed and its suitability for light control providing safer nighttime driving.     

Grande vitesse ferroviaire et développement économique local : une revue de la littérature

Many high-speed rail (HSR) projects exist in Europe and elsewhere in the world and generate many expectations: economic development, location of new firms and new population, development of tourism, effect on real estate. But these expectations are not always fulfilled. For academic researchers, the myth of the existence of a linear causality between transport infrastructures and spatial, social and economic transformations, according to which automatic effects will occur, has been challenged for a long time. But sometimes, new economic dynamism can be observed. The aim of this paper is to present a review of academic and non-academic literature in order to understand why there is a gap between the academic literature and the regional stakeholders’ expectations.     

Capacity estimation of torque converters with piston holes using the response surface method and an artificial neural network

In new slim torque converters, lock-up clutches are used to provide high fuel efficiency at low speed. However, the slimness of the converters causes difficulty in heat dissipation, which may damage the friction material and shorten its life span. A cooling hole in the lock-up piston reduces the heat but also reduces the torque because oil flows through the hole due to the pressure difference between the two faces of the piston. In the early stages of the development of this type of torque converter, designers must consider the minimum flow rate required to cool the friction material and the minimum torque capacity required to transmit the engine torque. This research explored two methods of estimating these parameters. In the first method, an estimation equation was derived by combining the response surface method with physical properties such as the centrifugal force, a sudden expansion, a sudden contraction, and the steady flow energy equation. The second method involved the use of an artificial neural network. The feasibility of the estimates based on statistics and on the artificial neural network were confirmed in the design stage by comparing experimental and estimated data. An estimation program was created using the C#.Net language and has been used for actual torque converter designs by the Korea Powertrain Company.     

顶湖—仙渡345 kV地下输电线路工程设计与施工

因都会区用电量增加,且为减低输电线路对市区景观及环境冲击,台电公司于台北市北投区大度路旁兴建地下电缆洞道,由顶湖超高压变电所引入345 kV二回线至仙渡超高压变电所。采用潜盾工法以降低交通及环境冲击的问题,因施工遭遇软硬不同土层及高水压影响,且穿越捷运淡水线关渡隧道下方,紧邻大度陆桥,因此在设计上采用大洞道方案、2道止水条、发进井调整位置及角度等方案,以降低施工对于附近结构物之冲击。     

A review of household dynamic vehicle ownership models: holdings models versus transactions models

Among disaggregate vehicle ownership models, which model the number and/or type of vehicles owned at the household level, one can distinguish holdings models, which deal with the (optimal) household fleet at a single point in time, and transactions models. The latter type of model explains changes to the household fleet, such as replacement and disposal. The paper describes previous attempts at such dynamic models and sketches how a vehicle transactions model could look (as an example we discuss an application to The Netherlands). This includes discussions of transaction probabilities, two-stage budgeting, introducing vehicle quality in the utility functions, and the envisaged model structure and data it could use.     

自由衰减模型试验的横摇阻尼评估方法研究

The methodology to obtain the non-linear roll damping from decay tests is very old. It has been proposed by Froude in the 19th century and used from then on. Behind it there is a quadratic model [θ│θ│] for the damping and a subsequent equivalent linearization. Probably all model basin in the world follows this approach to assess the damping from a decay test. This is well documented and so is the methods to get the p1-p2 coefficients. This is very general in the sense that in principle,it could be applied t...     

澳大利亚煤层甲烷项目为未来发展提供了路标

随着美国保德河和圣胡安盆地裸眼煤层甲烷项目的成功开发,20世纪90年代末,澳大利亚的经营者们开始钻探裸,眼垂直并。此后的几年间,澳大利亚早期煤层甲烷经营者凭借着自身的聪明才智、积极创造和灵活变通,使气井设计取得了世界上其它任何煤层甲烷开发项目中前所未有的进展。这些经营者目前正在实施结构复杂的多层多边地表内层（SIS）气井设计,这种设计有望开采全球的煤层甲烷储层。     

编者的话

制造是汽车工业的重要环节,更是汽车业利润的重要来源之一。中国汽车工业协会助理秘书长杜芳慈日前指出：“作为制造业的汽车产业,大部分利润应该来源于制造环节。而不是汽车金融和售后服务等环节。同时,应该把5％确定为整车制造的利润率红线。低于这个比率,汽车研发、生产将很难保证。”