Active coolant control strategies in automotive engines

The coolant flow rate in conventional cooling systems in automotive engines is subject to the mechanical water pump speed, and high efficiency in terms of fuel economy and exhaust emission is not possible given this limitation. A new technology must be developed for engine cooling systems. The electronic water pump is used as a substitute for the mechanical water pump in new engine cooling systems. The new cooling system provides more flexible control of the coolant flow rate and engine temperature, which previously relied strongly on engine driving conditions such as load and speed. In this study, the feasibility of two new cooling strategies was investigated using a simulation model that was validated with temperatures measured in a diesel engine. Results revealed that active coolant control using an electronic water pump and valves substantially contributed to a reduction of coolant warm-up time during cold engine starts. Harmful emissions and fuel consumption are expected to decrease as a result of a reduction in warm-up time.     

Traffic-balancing algorithm for can systems with dual communication channels to enhance the network capacity

The controller area network (CAN) is the dominant protocol for in-vehicle network (IVN) systems because it provides bounded transmission delay among electronic control units (ECUs) at data rates between 100 Kbps and 1 Mbps. Many automotive companies have chosen the CAN protocol for their chassis network system of intelligent vehicles. However, the increasing number of ECUs in intelligent vehicles and the need for more intelligent functions require a network system with more network capacity and real-time capability. As one approach to enhance the network capacity of a CAN system, this paper introduces a CAN system with dual communication channels. This paper also presents a traffic-balancing algorithm that predicts the traffic of each channel and allocates frames to the most appropriate channel. An experimental testbed using commercial off-the-shelf microcontrollers with two CAN controllers was used to demonstrate the feasibility of the traffic-balancing algorithm.     

Development of the Sungkyunkwan University Driving Simulator (SKUD) for Human-Machine Interface studies of Car Navigation Systems

Driving simulators are useful tools that can be used not only to test the components of future cars, but also to evaluate the telematics service and HMI (Human-Machine Interface). However, driving simulators that are currently available cannot be implemented to test and evaluate a real commercial telematics service system because the GPS (Global Positioning System), which contains basic functional support for the telematics module, does not work in the VR (virtual reality) environment. A driving simulator, together with the GPS simulator, can be used to study the HMI to evaluate commercial CNS (Car Navigation Systems). In this paper, Sungkyunkwan University Driving Simulator (SKUD) is developed with a GPS simulator that is able to emulate GPS satellite signals and includes the NMEA-0183 protocol and RS232C communication standards. Furthermore, using the SKUD, the HMI of the real commercial CNS could be investigated with driver workload assessment methods.     

License plate location method unaffected by variation in size and aspect ratio

License plate location is a challenging task that is necessary for automatic vehicle identification. This paper presents a new method for locating a license plate when its size and aspect ratio are highly variable. The proposed method begins with an assumption that a license plate exists in a region where dense edges are located. We define an edge region as an area containing rich edges. The edge regions are created by dilating vertical edges, and they are classified into one of four types: left fragment type, right fragment type, whole type, and undefined type. The candidates for a license plate region are constructed by merging edge regions. Knowing what type of edge region is being examined is useful in the merging process. Finally, we verify whether each candidate contains a license plate or not by using the character arrangement information. The arrangement pattern is determined by the size of connected components and by the vertical overlap or horizontal distance between two neighboring components. Experimental results show that the proposed method gives robust results regardless of any variation in the size and aspect ratio of license plates.     

新安船装载的紫檀木和国际贸易

在新安船上装载的与新安船的交易活动范围有关的商品中,最突出的是陶瓷器、铜钱和紫檀木,紫檀木是从属于热带以及亚热带的东南亚购入的,而当时前往东南亚、印度、阿拉伯地区的中国商船主要从泉州港出发.由于泉州湾宋代海船的出土,新安船被认为是在福建地区制造的泉州船舶.新安船是以东南亚和中国以及东北亚作为活动舞台的贸易船,在向最终目的地日本博多航行过程中,经过高丽沿岸时遇难,最终没能返回.新安船装载的1017根紫檀木,是把新安船的研究范围扩大到中国和日本以外的东南亚和西域的重要资料.     

Investigation of the shear flows over a sunroof opening based on a linear inviscid instability analysis

The large-scale shear flows over the sunroof opening of a mid-sized SUV measured using a PIV system were investigated. The shear flows were measured for five different cases of deflector protrusion (one case was the baseline test without deflector) at two different free stream flow velocities below the critical velocity where the buffeting noise level reached a maximum. The structures of the shear flows were observed to differ, apparently depending on whether the radiated buffeting noise is relatively strong or not. For strongly buffeting experimental cases, the momentum thicknesses of the shear layers were observed to grow rapidly and saturated at a station near the downstream edge of the sunroof opening, where the saturation of the transverse velocity fluctuations was also observed, and where the vortex coalescence process was presumably completed. On the other hand, no discrete large-scale vortex structures were observed for none-buffeting or weakly buffeting cases. Streamwise growth of the velocity fluctuations was found to be well predicted by a linear hydrodynamic instability analysis for the strongly buffeting cases. Numerical results obtained from a linear inviscid instability analysis using a hyperbolic tangent mean velocity profile were used to calculate the amplification factors with the initial momentum thickness and the streamwise fluctuation wavenumber. The shear flows were found to form large-scale discrete vortices when the linear inviscid amplification factors exceeded a threshold amplification factor.     

Performance analysis of a CVT clutch system for a hybrid electric vehicle

In this study, the performance of a CVT clutch system for a hybrid electric vehicle was investigated. To analyzed the vehicle performance at restart, the restart delay and driveshaft torque was investigated by simulations and experiments. It was found from the simulation results that the vehicle restart response depends on the clutch pressure buildup time to the point where the clutch torque begins to overcome the vehicle road load, and driving comfort at restart is directly related to the rate change of the clutch pressure.     

OH-radical behavior of unsteady lifted flame based on instantaneous change of the equivalence ratio

In an earlier study, the current authors showed that an unsteady-state lifted flame generated by an equivalence ratio conversion system for a given fuel, was similar to a steady-state lifted flame in terms of the change characteristics from a premixed flame to a critical flame and then to a triple flame with a diffusion flame positioned in the middle according to the concentration difference. Therefore, this study used an OH-PLIF method to investigate the characteristics of a steady-state lifted flame and an unsteady-state lifted flame created under conditions identical to the flames in the preceding study. PLIF (Planar laser induced fluorescence) is practically effective for visualizing the concentration fields within a flame. The resulting OH-radical measurements showed that an unsteady-state lifted flame created under the specific conditions used in this study showed similar tendencies in terms of OH-radical distribution, fluorescence intensity, and liftoff height, to a steady-state lifted flame, thereby confirming that the behavior of an unsteady-state lifted flame can be effectively predicted based on the behavior of a steady-state lifted flame.     

Study of RCM-based maintenance planning for complex structures using soft computing technique

To guarantee the efficiency of maintenance strategies for a complex structure, safety and cost limitations must be considered. This research introduces RCM-based (Reliability Centered Maintenance) life cycle optimization for reasonable maintenance. The design variable is the reliability of each part, which consists of a complex structure, while the objective is to minimize the total cost function in order to maintain the system within the desired system reliability. This research constructs the cost function that can reflect the current operating condition and maintenance characteristics of individual parts by generating essential cost factors. To identify the optimal reliability of each component in a system, this paper uses a Neuro-Evolutionary technique. Additionally, this research analyzes the reliability growth of a system by using the AMSAA (Army Material Systems Analysis Activity) model to estimate the failure rate of each part. The MTBF (Mean Time Between Failure) and the failure rate of the whole system, which is responding to the individual parts, are estimated based on the history data by using neural networks. Finally, this paper presents the optimal life cycle of a complex structure by applying the optimal reliability and the estimated MTBF to the RAMS (Reliability, Availability, Maintainability, and Safety) algorithm.     

Effects of split injection,oxygen enriched air and heavy EGR on soot emissions in a diesel engine

The effects of split injection, oxygen enriched air, and heavy exhaust gas recirculation (EGR) on soot emissions in a direct injection diesel engine were studied using the KIVA-3V code. When split injection is applied, the second injection of fuel into a cylinder results in two separate stoichiometric zones, which helps soot oxidation. As a result, soot emissions are decreased. When oxygen enriched air is applied together with split injection, a higher concentration of oxygen causes higher temperatures in the cylinder. The increase in temperature promotes the growth reaction of acetylene with soot. However, it does not improve acetylene formation during the second injection of fuel. As more acetylene is consumed in the growth reaction with soot, the concentration of acetylene in the cylinder is decreased, which leads to a decrease in soot formation and thus soot emissions. A combination of split injection, a high concentration of oxygen, and a high EGR ratio shows the best results in terms of diesel emissions. In this paper, the split injection scheme of 75.8.25, in which 75% of total fuel is injected in the first pulse, followed by 8°CA of dwell time, and 25% of fuel is injected in the second pulse, with an oxygen concentration of 23% in volume and an EGR ratio of 30% shows a 45% reduction in soot emissions, with the same NOx emissions as in single injection.