隧道外挂设漏泄同轴电缆接口分析

山区铁路隧道外挂设漏泄同轴电缆的情况越来越多,漏缆隧道外挂设所涉及的参数、接口、设置要求等方面尚无可参照的规范标准,基于沪昆客运专线湖南段隧道群挂设漏缆的工程实例,总结隧道外漏缆挂设的工程接口、参数等信息经验,以供其他工程借鉴参考.     

Micro-Grinding Performance of Hard-Brittle Chip Materials in Precision Micro-Grinding Microgroove

The micro-structure on hard-brittle chip materials (HBCMs) surface can produce predominant functions and features. The micro-grinding with diamond wheel micro-tip is an efficient method to machine microstructure on HBCMs. However, different HBCMs and crystal orientation may have a significant influence on the micro-grinding performance. In this paper, the micro-grinding performance along different crystal orientation of HBCMs is investigated. First, a dressed 600^# diamond grinding wheel is used to micro-grind micro-structure on HBCMs. Then, the experiment of micro-grinding force test is completed. Finally, the quality of microgroove, the grinding ratio and the micro-grinding force are investigated and they are related to the crystal orientation of HBCMs. It is shown that the stronger resistance to the micro-crack propagation has the best quality of microgroove and the smallest grinding ratio. Moreover, the hardest single-crystal SiC has the best machinability and the micro-grinding force is 38.9%, 10.8% and 46.8% less than the one of sapphire, single-crystal Si and quartz glass, respectively. The direction to micro-grind easily is the crystal orientation 〈10\(\overline 1 \)0〉 for single-crystal SiC and sapphire. In addition, the micro-grinding force increases with the increase of the micro-grinding depth and feed rate and decreases with the increase of the grinding wheel speed.     

Lattice-based group signature with verifier-local revocation

Among several post quantum primitives proposed in the past few decades, lattice-based cryptography is considered as the most promising one, due to its underlying rich combinatorial structure, and the worst-case to average-case reductions. The first lattice-based group signature scheme with verifier-local revocation(VLR) is treated as the first quantum-resistant scheme supported member revocation, and was put forward by Langlois et al. This VLR group signature(VLR-GS) has group public key size of O(nm log N log q), and a signature size of O(tm log N log q log β). Nguyen et al. constructed a simple efficient group signature from lattice, with significant advantages in bit-size of both the group public key and the signature. Based on their work, we present a VLR-GS scheme with group public key size of O(nm log q) and signature size of O(tm log q). Our group signature has notable advantages: support of membership revocation, and short in both the public key size and the signature size.     

提速道岔启动电路分析

为保证提速道岔的可靠运用,在设计方案上对提速道岔启动电路进行了时序控制,减少同时转换提速道岔的转辙机数量,使道岔转辙机转换电流峰值控制在合理的范围内,保证各信号设备正常工作。     

250km/h客运专线无砟道岔的合理轨道刚度

研究目的:我国正在进行大规模的客运专线建设,其中时速250 km的客运专线占有相当大的比重.无砟道岔作为客运专线的重大基础设备,其轨道刚度影响动车组过岔时的安全性和平稳性,需进行合理设置.根据线路运营条件,运用理论分析,开展客运专线无砟道岔轨道刚度取值研究,为确定我国250 km/h客运专线无砟道岔的合理轨道刚度提供理论指导.研究结论:从列车运行品质、道岔应力状态、振动水平、变形大小和部件刚度匹配5个方面提出岔区合理轨道刚度的评判准则,并基于车辆一道岔空间耦合动力学理论和轨道变形分析建立岔区合理轨道刚度的确定方法,对我国时速250 km客运专线无砟道岔轨道的合理刚度进行了研究,结果表明:36～44 kN/mm的扣件系统刚度,290～330 kN/mm的轨下胶垫刚度,40～50 kN/mm的板下胶垫刚度最为合理.     

钢弹簧浮置板轨道结构静力学分析

建立钢弹簧浮置板轨道结构有限元模型,对其进行静力学分析。首先分析了剪力铰对钢轨和浮置板垂向位移的影响;其次分析了弹簧支座间距对浮置板应力和弯矩分布的影响;最后计算了不同扣件刚度和支座刚度组合时浮置板轨道结构的变形和受力,为今后优化钢弹簧浮置板轨道结构的设计提供了理论依据。     

城市轨道交通换乘站综合监控平台的构建

介绍了车站级综合监控平台及其功能。整合了换乘站各弱电系统,给出了弱电系统接入综合监控平台的方式。在此基础上,针对全新2线换乘站提出了车站综合监控平台构建的三种方案,并对其进行了对比分析,确定了三种方案的适用情况。     

客流预测成果在地铁行车组织设计中的应用

结合南宁轨道交通1号线的设计前期工作,对客流量级进行阐述,分析客流预测三级数据,确定运营的规模;根据OD客流分析来研究行车交路,做出满载率和拥挤度的评价,最终确定车辆编组与行车密度的组合,从而形成合理的运营方案。     

CA498柴油机冷却水流LDV测量

为验证柴油机冷却水套CFD计算结果的准确性，利用LDV测速系统测量了CA498柴油机缸盖及缸体内流场12个关键点处的速度，并将试验结果与CFD计算结果进行了比较一结果表明，除了缸体上3个点的实际测量结果与CFD计算结果有较大偏差以外，其他各点试验测得的数据与CFD计算结果有较好的一致性。分析了造成偏差的主要原因。     

高速公路路堤和路面软基病害检测及加固处理

某高速公路 K1 0 4 2 0 0～K1 0 6 5 0 0段穿过鱼塘 ,路堤采用钢渣水中挤淤法施工 ,通车后路面出现了严重的纵向裂缝、车辙、沉陷 ,影响了路面的使用性能 ,同时路堤存在滑动的隐患 ,必须进行加固处理。为此 ,首先通过系统检测 ,分析路面裂缝产生的原因 ,然后提出针对性的加固处理方案 ,最终实施加固处理施工 ,所取得的成果对其它高速公路的维修加固具有参考价值