Soot and temperature distribution in a diesel diffusion flame: 3-D CFD simulation and measurement with laser diagnostics

In this study, a 3-D CFD simulation and laser diagnostics were developed to understand the characteristics of soot generation in a diesel diffusion flame. The recently developed RANS (Reynolds-averaged Navier-Stokes equations) hybrid combustion model (Extended Coherent Flame Model — 3 Zones, ECFM-3Z model) was used. This industrial, state-ofthe-art model of the diffusion flame is commonly used in diesel combustion models as well as for propagating (premixed) flame combustion. The simulation results were validated with measurements from a constant volume combustion chamber. The experiment revealed that soot accumulated in the chamber where the temperature decreased. Where the temperature increased rapidly, only a little soot accumulated. The temperature and soot distribution were independently examined using both the two-color method and a 3-D CFD simulation for a turbulent diesel diffusion flame.     

Measurement of the disc-pad friction coefficient for mechanical brakes using direct and indirect methods

It is necessary to guarantee the proper brake force to stop a train safely in a limited distance and o adjust its speed. Currently, most trains are run by electrical power and have a combined electrical and mechanical (friction) braking system. The mechanical brake force is determined by many parameters, such as the friction coefficient of the brake disc and pad, the pressure in the brake cylinder, the brake cylinder’s cross sectional area and the brake linkage ratio. In general, the friction coefficient data of the brake disc and pad have been taken through a dynamo-test in a laboratory, but these data might not be well matched with real data under operating conditions because of the difference in data acquisition conditions. The present study examined two methodologies that can measure the friction coefficient of the brake pad and disc based on a train’s real operating conditions. The first method was the direct method, which measured the brake force and clamping force applied on the mechanical brake by using strain gauges installed on the brake to calculate the friction coefficient. The second was an indirect method that obtained the friction coefficient by using the weight of the train and the equivalent brake force. Those variables were calculated from the longitudinal dynamic characteristics, such as resistance to motion, gradient resistance and curved resistance. These two methodologies were used to obtain the disc-pad friction coefficient for the mechanical brakes of a Korean high-speed train (HSR350x).     

Sliding-mode-based parameter identification with application to tire pressure and tire-road friction

This paper presents a method of simultaneous estimation of tire pressure and tire-road friction. A sliding-mode scheme is designed to identify the system state and the parameter variation of a torsional tire system, which greatly depend on the change in tire pressure. Then, the recursive least-squares method with a forgetting facto is used to estimate the parameter variations of the tire system and the tire-road friction force without a friction model using the information retrieved from the equivalent input for sliding motion. A simulation study is performed to illustrate the effectiveness of the proposed method.     

Relationship between occupant injury and the perturbation mark on the velocity indicator on a cluster panel

A perturbation mark is occasionally produced on the velocity indicator of the cluster panel of a vehicle during a vehicle collision. This mark can be used to estimate the velocity of the vehicle at the moment of the vehicle’s impact. In this study, the effect of the impact velocity and the deceleration of the vehicle on the perturbation mark were investigated, and an analysis of the driver’s injury was also conducted through a numerical pulse representation and computer simulations. Sled and pendulum tests were used to replicate the conditions that produce a perturbation mark on the velocity indicator of a cluster panel. It was verified that a higher peak acceleration is more likely than the impact velocity to cause a perturbation mark. According to the computer simulation results, a driver’s injury could be more severe at higher peak accelerations with a constant impact velocity. If a perturbation mark, which can be used to estimate the impact velocity, is found while investigating a vehicle accident, this mark reveals that the acceleration was higher than that listed in the related crash report. Therefore, the injuries of the occupants could be more serious than those expected at the reported impact velocity.     

Review on characterization of nano-particle emissions and PM morphology from internal combustion engines: Part 2

This paper presents a review of the characterization of physical properties, morphology, and nanostructure of particulate emissions from internal combustion engines. Because of their convenience and readiness of measurement, various on-line commercial instruments have been used to measure the mass, number, and size distribution of nano-particles from different engines. However, these on-line commercial instruments have inherent limitations in detailed analysis of chemical and physical properties, morphology, and nanostructure of engine soot agglomerates, information that is necessary to understand the soot formation process in engine combustion, soot particle behavior in after-treatment systems, and health impacts of the nano-particles. For these reasons, several measurement techniques used in the carbon research field, i.e., highresolution transmission electron microscopy (HRTEM), X-ray diffraction (XRD), and Raman spectroscopy, were used for analysis of engine particulate matter (PM). This review covers a brief introduction of several measurement techniques and previous results from engine nano-particle characterization studies using those techniques.     

H8 Control Performance of a Full-Vehicle Suspension Featuring Magnetorheological Dampers

Summary This paper presents an investigation of the feedback control performance of a full-vehicle suspension system featuring magnetorheological (MR) dampers. A cylindrical MR damper is designed and manufactured by incorporating a Bingham model of aMR fluid which is commercially available. After evaluating the field-dependent damping characteristics of the MR damper, a full-vehicle suspension system installed with 4 independent MR dampers is constructed and its governing equations of motion which include vertical, pitch and roll motions are derived. A H 8 controller which has inherent robustness against system uncertainties is formulated by treating the sprung mass of the vehicle as uncertain parameter. This is accomplished by adopting the loop shaping design procedure. For the demonstration of a practical feasibility, control performance characteristics for vibration suppression of the proposed MR suspension system are evaluated under various road conditions through the hardware-in-the-loop simulation (HILS) methodology.     

GROWTH DIFFERENTIATION FACTOR-5 STIMULATES THE GROWTH AND ANABOLIC METABOLISM OF ARTICULAR CHONDROCYTES

Growthdifferentiationfactor5(GDF5),also knownascartilage derivedmorphogeneticprotein1(CDMP1),isamemberofthebonemorphogenet icprotein(BMP)familywhichbelongstothe transforminggrowthfactorβ(TGFβ)superfami ly[1].GDF5isarelativelynewmemberofthe BMPfamily.LikeotherBMPs,implantationofre combinantGDF5caninduceectopiccartilagefor mationinmusculartissues.Thephysiologicalrole ofGDF5hasbeenreportedincludingregulationof myogenesis,regulationofchondrogenesis,bone morphogenesis,andneurondifferen…     

Fatigue and buckling analysis of automotive components considering forming and welding effects

Some vehicle components are developed by setting target weights to the gram level at their design stages to accomplish a lightweight design. Recently, there have been many studies that have focused on lightweight design through the use of ultra-high-strength steels. However, a lightweight design can face many challenges if the reliability of the analysis is not also secured at the design stage. Such challenges include difficulties in coupled analyses when the file formats are different among PAM-STAMP, ABAQUS, and NASTRAN. In this study, we developed a mapping interface that enables mapping between the file formats of various software programs. Buckling analysis was coupled to the forming analysis, in which pre-strain test data were applied in considering the material’s strain hardening, to evaluate the rigidity of the front lower control arm that controls the wheels and transfers loads. The influence of forming effects on endurance was evaluated, and residual stresses around the weld zone were calculated. A comparison of experimental and analytical results indicated that the proposed analysis was highly reliable.     

Estimation of lateral offset and drift angle for application in secondary collision avoidance system

Recent reports show that the secondary collision on the road gives much higher fatality rate than the other traffic accidents. Many studies have been carried out to prevent the secondary accidents and as a result automotive companies began to introduce brake-based secondary collision avoidance systems. To prevent the secondary accidents it is important to monitor and control the lateral deviation of the vehicle after the primary collision. An estimator for the vehicle’s lateral offset and drift angle based on the in-vehicle sensors and the camera was developed in this paper. By employing sensor fusion scheme and applying extended Kalman filter, the estimator has been designed so that it works even when the camera loses the image of the lanes due to sudden change of the vehicle’s heading angle. For validation of the estimator, simulation has been carried out on various collision scenarios. The simulation results indicated that the estimator of this paper could calculate the vehicle’s lateral deviation with robustness that may be required for application in the secondary collision avoidance systems.     

Estimating vehicle miles traveled (VMT) in urban areas using regression kriging

The recent increase in demand for performance‐driven and outcome‐based transportation planning makes accurate and reliable performance measures essential. Vehicle miles traveled (VMT), the total miles traveled by all vehicles on roadways, has been utilized widely as a proxy for traffic impact assessment, vehicle emissions, gasoline consumption, and crashes. Accordingly, a number of studies estimate VMT using diverse data sources. This study estimates VMT in the urban area of Bucheon, South Korea, by predicting the annual average daily traffic for unmeasured locations using spatial interpolation techniques (i.e., regression kriging and linear regression). The predictive performance of this method is compared with that of the existing Highway Performance Monitoring System (HPMS) method. The results show that regression kriging could provide more accurate VMT estimates than the HPMS method and linear regression, especially with a small sample size. Copyright © 2016 John Wiley & Sons, Ltd.