Optimizing the shape of a bumper beam section considering pedestrian protection

This paper presents a design technique to optimize the shape of a vehicle bumper beam that satisfies both the safety requirements for a front rigid-wall impact and the regulations protecting pedestrians from lower leg injuries caused by bumper impacts. An intermediate response surface modeling (IRSM) technique was introduced to approximate the non-linear force-displacement curves obtained from the front impact analysis of a vehicle bumper. The accuracy of the IRSM model was tested by comparing its results with those of the non-linear finite element analysis. The maximum displacement error between the two models did not exceed 3%. Using pedestrian impact analyses based on the experimental arrangement of the Plackett-Burman design, the approximate functions describing the response values acting on the lower legs were calculated. The shape of the bumper beam was optimized by integrating the IRSM with the force-displacement model and the approximate functions on lower leg impact. The optimization results satisfied safety regulations on the maximum allowable displacement of the vehicle bumper, and also the regulations protecting pedestrians from lower leg injuries caused by bumper impacts.     

Effect of various LPG supply systems on exhaust particle emission in spark-ignited combustion engine

The particle size distribution and particle number (PN) concentration emitted by internal combustion engine are a subject of significant environmental concern because of their adverse health effects and environmental impact. This subject has recently attracted the attention of the Particle Measurement Programme (PMP). In 2007, the UN-ECE GRPE PMP proposed a new method to measure particle emissions in the diluted exhaust of automotive engines and a regulation limit (<6.0×10¹¹ #/km, number of particles). The specific PN regulation of spark-ignited combustion engine will be regulated starting on September 1, 2014 (EURO 6). In this study, three types of LPG supply systems (a mixer system and a multi-point injection system with gas-phase or liquid-phase LPG fuel) were used for a comparison of the particulate emission characteristics, including the nano-sized particle number density. Each of the three LPG vehicles with various LPG injection systems contained a multi-cylinder engine with same displacement volumes of 2,000 cm³ and a three-way catalytic converter. The test fuel that was used in this study for the spark-ignited combustion engine was n-butane basis LPG fuel, which is primarily used for taxi vehicles in Korea. The characteristics of nano-particle size distribution and number concentration of particle sizes ranging from 20 to 1,000 nm (aerodynamic diameter) that were emitted from the three LPG vehicles with various LPG supply systems were investigated by using a condensation particle counter (CPC), which is recommended by the PMP under both the NEDC and FTP-75 test modes on a chassis dynamometer. The experimental results indicate that the PN emission characteristics that were obtained by the CPC system using the PMP procedure are sufficiently reliable compared to other regulated emissions. Additionally, the sources of PN emissions in ascending order of magnitude are as follows: mixer type, gas-phase LPG injection (LPGi) and liquid-phase LPG injection (LPLi) passenger vehicles. The liquid-phase LPG injection system produced relatively large particle sizes and number concentrations compared to the gaseous system, regardless of the vehicle driving cycle. This phenomenon can be explained by unburned micro-fuel droplets that were generated due to a relatively short homogeneous fuel-air mixture duration in the engine intake manifold. Also the particle number emissions from the LPG vehicle were influenced by the vehicle driving cycle.     

Analytical study to estimate the performance of the Power Shift Drive (PSD) Axle for a forklift

In this study, a new concept for a power delivery system is developed. Power Shift Drive (PSD) Axle vehicle modeling and dynamic movement analysis are performed via simulation. The dynamic vehicle model is constructed from data obtained from the derived equation, considering the specific characteristics of each part. The model is composed of a torque converter, a gear box, a differential, hub reduction and an engine, which is the power source of the 1st forward and reverse PSD-Axle. By unifying the mathematical equations for each component, a mathematical model of the 1st forward gear is derived. The system dynamic model is created using MATLAB/Simulink based on the mathematical model. Simulation is carried out using Simulink to estimate the dynamic behavior of the PSD-Axle. In addition, the dynamo test result is used to verify the model. Finally, a successful model is created. This study will be used to establish the basic conceptual design for the PSD-Axle multi-gear system.     

Effects of FTP-75 mode vehicle fuel economy improvement due to types of power steering system

This paper focuses on fuel economy improvement according to the type of power steering system. Usually, a conventional power steering system is directly driven by the crankshaft of the engine with a belt, known as HPS (hydraulic power steering). However, there is some inefficiency with this system at high engine speeds. To improve this inefficiency, automobile makers have developed two power steering systems: EHPS (electro-hydraulic power steering) and MDPS (motor-driven power steering) or EPS (electric powered steering). However, there has been insufficient study of effects of the type of power steering system on fuel economy. In this paper, the effect of the type of power steering system on fuel economy is studied experimentally, and calculations of the effect on vehicle fuel economy are presenting using computer simulation with AVL cruise software. The results demonstrate that a 1% vehicle fuel economy improvement can be achieved in a vehicle with an electro-hydraulic power steering system compared to a vehicle with a hydraulic power steering system. In addition, a 1.7% vehicle fuel economy improvement can be achieved using a full electric power steering system in a FTP-75 driving cycle. These results could be used to choose a power steering system.     

High speed tensile test of steel sheets for the stress-strain curve at the intermediate strain rate

This paper presents stress-strain curves of steel sheets for an auto-body obtained at intermediate strain rates with a servo-hydraulic type high speed tensile testing machine. The apparatus has the maximum stroke velocity of 7.8 m/sec to obtain the tensile material properties at a strain rate of up to 500/sec. A special jig fixture is specially designed for accurate acquisition of tensile loads with reduction of the load-ringing phenomenon induced by unstable stress wave propagation at high strain rates. Tensile testing of steel sheets for an auto-body was carried out to obtain stress-strain curves of mild steel and advanced high strength steels at strain rates ranged from 1/sec to 200/sec. The test results provide interesting information regarding the stress-strain curves at intermediate strain rates ranged from 1/sec to 200/sec and demonstrate that strain rate hardening is strongly coupled with strain hardening.     

Effects of valve timing and intake flow motion control on combustion and time-resolved HC & NOx formation characteristics

In SI engines, valve events have a major influence on volumetric efficiency, fuel economy and exhaust emissions. Moreover, swirl and tumble motions in the intake charge also improve combustion speed and quality by stratifying the mixture as well as intensifying the mixing rate of air and fuel. This paper investigates the behaviors of an engine and the combustion phenomenon for various intake valve timings and intake charge motions using CVVT system and port masking schemes. Test condition includes a part load and a cold idle condition inclusive of a cold start of the engine. Time-resolved HC and NOx emissions were also measured at an exhaust port to examine their formation mechanisms and behaviors with fast response HC/NOx analyzers. In conclusion, the fast burning of fuel and improved combustion quality by enhanced charge motions reduced unburned HC emissions, and advancing the intake valve opening reduced HC as well as NOx. Furthermore, HCs during the cold transient phase and idle conditions decreased with recalibrated start parameters such as lean air-fuel ratio and spark retardation via the enhancement of intake charge motions.     

Study of RCM-based maintenance planning for complex structures using soft computing technique

To guarantee the efficiency of maintenance strategies for a complex structure, safety and cost limitations must be considered. This research introduces RCM-based (Reliability Centered Maintenance) life cycle optimization for reasonable maintenance. The design variable is the reliability of each part, which consists of a complex structure, while the objective is to minimize the total cost function in order to maintain the system within the desired system reliability. This research constructs the cost function that can reflect the current operating condition and maintenance characteristics of individual parts by generating essential cost factors. To identify the optimal reliability of each component in a system, this paper uses a Neuro-Evolutionary technique. Additionally, this research analyzes the reliability growth of a system by using the AMSAA (Army Material Systems Analysis Activity) model to estimate the failure rate of each part. The MTBF (Mean Time Between Failure) and the failure rate of the whole system, which is responding to the individual parts, are estimated based on the history data by using neural networks. Finally, this paper presents the optimal life cycle of a complex structure by applying the optimal reliability and the estimated MTBF to the RAMS (Reliability, Availability, Maintainability, and Safety) algorithm.     

KERFIX, a time-series station in the Southern Ocean: a presentation

Between January 1990 and March 1995, the research project KERFIX undertook the first regular noncoastal multiyear acquisition of parameters related to the carbon cycle in the Southern Ocean at a time series station located at 50°40′ S–68°25′ E, 60 miles southwest of the Kerguelen Islands. The objectives of KERFIX are (1) to monitor the ocean/atmosphere CO₂ and O₂ exchanges and to understand which processes govern these exchanges (2) to observe and interpret the seasonal and interannual variability of the production, flux, decomposition and dissolution of carbon and associated elements at this location. In addition, micropaleontological studies describe the present and past flux dynamics in this oceanic area, to improve the knowledge of the transfer functions of some oceanographic proxies. This paper presents a survey of the KERFIX program: scientific objectives, organization of the field operations and some main results obtained since the beginning of KERFIX program, as well as the results of the temporal evolution of hydrological, chemical and biological parameters.     

Precise estimation of connections of metro passengers from Smart Card data

The aim of this study is to estimate both the physical and schedule-based connections of metro passengers from their entry and exit times at the gates and the stations, a data set available from Smart Card transactions in a majority of train networks. By examining the Smart Card data, we will observe a set of transit behaviors of metro passengers, which is manifested by the time intervals that identifies the boarding, transferring, or alighting train at a station. The authenticity of the time intervals is ensured by separating a set of passengers whose trip has a unique connection that is predominantly better by all respects than any alternative connection. Since the connections of such passengers, known as reference passengers, can be readily determined and hence their gate times and stations can be used to derive reliable time intervals. To detect an unknown path of a passenger, the proposed method checks, for each alternative connection, if it admits a sequence of boarding, middle train(s), and alighting trains, whose time intervals are all consistent with the gate times and stations of the passenger, a necessary condition of a true connection. Tested on weekly 32 million trips, the proposed method detected unique connections satisfying the necessary condition, which are, therefore, most likely true physical and schedule-based connections in 92.6 and 83.4 %, respectively, of the cases.     

朝鲜许筠求得李贽著作的过程

许筠被朝鲜学者称为朝鲜的李贽.李贽是阳明左派,许筠是儒学者徐敬德、李幌的左派,两人的思想和行为十分相似.当代韩国学术界在分析许筠的思想体系时,常将他与李贽相联系.许筠曾数次接待明廷使臣,又几度以使臣的身份出使明朝,期间购买许多书籍带回半岛.笔者在本文中对许筠何时、如何购得李贽的著作及其反应,进行集中考察.