排序方式: 共有1854条查询结果,搜索用时 15 毫秒
891.
This paper presents experimental results of the post-fire behavior of tubular T-joints. The research aims at the failure modes
and the residual strengths of the T-joints after fire. Three tests of full-scale tubular T-joints are conducted. The first
one is carried out to study the mechanical behavior of T-joints under ambient temperature. The other two tests are performed
to study the influence of pre-load, heating and cooling phase on residual load-bearing capacity of the tubular T-joints. The
test results show that the sustained axial load on the brace has remarkable influence on the residual deflection of the T-joints
which is cooled down to room temperature. The results of the experiments also indicate that the axial load level and heating
and cooling history have more significant effects on the compressive stiffness of the T-joints than the residual strength.
In the numerical study, the result of finite element model agrees well with the test result. The work in this paper provides
a basis for further parametric analysis and theoretical study on the structural evaluation after fire. 相似文献
892.
In this paper, a kind of mathematic method for optimizing stretching process of large forgings is proposed. Distributions
of effective strain within forged ingots is described by a Gauss function, which is obtained from the simulation of flat-anvil
stretching process. Successive stretching is expressed by the superimposing Gauss functions. Optimized stretching process,
with both homogeneous and certain strain in the center of forgings, is presented by derivation of this function. The relationship
between effective strain and the values of feed is obtained during the successive stretching with a rotation angle of 90°
and a feed displacement of 1/2 anvil width. The optimization result is verified by finite element simulation. Optimized value
of feed obtained using this method can ensure both uniformity and forging penetration. It provides mathematic model and theoretic
basis of optimizing large forging stretching process. 相似文献
893.
22MnB5 is one of the most typical hot stamping boron steels. In order to study the effect of austenitizing temperature and
holding time on the mechanical properties of hot stamping boron steel 22MnB5, a series of quenching process are done. The
tensile strength and hardness of 22MnB5 samples are measured. The results show that 22MnB5 has a good quenching performance,
and the tensile strength and hardness of samples quenched in a water-cooled steel die are similar to those of water quenching.
The higher tensile strength and HRC hardness are achieved when austenitizing at temperatures of 880–910 °C. Holding at 910
°C for 5 min and then quenching gives rise to a better combination of tensile strength, hardness and ductility. 相似文献
894.
A numerical study on bank effects in shallow channels is carried out by using a first-order Rankine source panel method. A
container ship sailing along a vertical bank and a sloping bank at different forward speeds, different water depths and different
distances between the bank and the ship hull is taken as example. The sway force and yaw moment acting on the hull are calculated
and the influences of the speed, water depth and distance between the bank and ship hull on the hydrodynamic force and moment
are analyzed. This study can provide insight into the bank effects, as well as to give guidance on ship manoeuvring and control
in restricted waterways, which is helpful to the navigation safety. 相似文献
895.
The performance of vacuum arc remelting (VAR) ingot depends largely on ingot structure and chemical uniformity, which are
strongly influenced by molten pool profile that is influenced by VAR process. To better understand the effect of remelting
current on molten pool profile of titanium alloy ingot during VAR process, a 3D finite element model is developed by the ANSYS
software. The results show that there are three remelting stages during VAR process when the remelting current is 2.0 kA.
The molten pool depth increases gradually from 30 to 320 s, then the change of molten pool depth is very small during the
steady state stage from 320 to 386 s, and lastly the molten pool depth becomes shallow after 386 s. The melting rate and temperature
of superheat increase with the remelting current increasing, which leads to the augment of molten pool volume. In the end,
the total remelting time and steady state molten pool time decrease with the melting current from 1.6 to 2.8 kA. 相似文献
896.
The quenching of a metal component with a channel section in a water tank is numerically simulated. Computational fluid dynamics
(CFD) is used to model the multiphase flow and the heat transfer in film boiling, nucleate boiling and convective cooling
processes to calculate the difference in heat transfer rate around the component and then combining with the thermal simulation
and structure analysis of the component to study the effect of heat transfer rate on the distortion of the U-channel component.
A model is also established to calculate the residual stress produced by quenching. The coupling fluid-thermal-structural
simulation provides an insight into the deformation of the component and can be used to perform parameter analysis to reduce
the distortion of the component. 相似文献
897.
In this paper, the effects of hardening exponent, yield strength and elastic modulus on the deformability of near hemispherical
shells are investigated by means of finite element method and orthogonal experiment design. The largest eccentric angle during
the deformation process and thickness reduction after the deformation are introduced to estimate the deformability quantitatively
according to the deformation characteristics of near hemispherical shells. The results indicate that the hardening exponent
is the most influential parameter, followed by elastic modulus and yield strength. The shell exhibits good deformability when
the hardening exponent and elastic modulus are in the range of 0.1–0.125 and 70–108 GPa, respectively. 相似文献
898.
In this paper, we consider a floating raft isolation system with elastic limiters. The limiters might be “contact” or “no
contact”, thus forming a unilateral system generating possible contacts. In order to avoid the large displacement of the floating
raft under shock, limiters might be adopted but good limiters design requires the values of the gaps. Based on the contact
dynamics, the multi-degree-freedom dynamic model of floating raft isolation system with elastic limiters is established. The
artificial neural network has been developed to dingtinguish the contact state of elastic limiters at each step. The example
analysis shows that the algorithm of neural network for contact can shorten the time of caclaution. From the example analysis,
we get some interesting results that may be useful to the ship engineering. 相似文献
899.
A biomechanical musculo-skeletal model of upper limb is presented in this paper, which can provide accurate representations
of muscles and joints, and capture important interactions between joints. The upper limb model is made up of seven segments:
ribs, sternum, clavicle, scapular, humerus, radius and ulna, considered as a single rigid body respectively and includes 22
muscles. The individual muscle forces can be calculated by using an electromyography (EMG) assisted method, which is verified
by comparing the simulation results with other researches of an elbow flexion motion. These comparisons show that the muscle
forces and the estimated joint moment match well with previous literatures. 相似文献
900.
The feasibility of electromagnetically stimulated thermography non-destructive testing (NDT) for the detection of defects
in metallic conductive materials has been carried out by finite element analysis. Aluminum plates with defects of different
diameters, depths, locations, shapes and orientation with respect to eddy current are numerically investigated. ANSYS software
is used to solve the coupled electromagnetic and temperature field equations. The peak temperatures on the top surface of
circular defects with different diameters and depths are calculated at varying excitation frequencies. It is demonstrated
that the obtained temperature inreases with increase of the defect diameter and decrease of its depth. The dependence of the
temperature over the top surface of the defect on its location and orientation is also presented. The results indicate that
we can detect the subsurface defect and estimate its depth and location by choosing a suitable coil-specimen configuration. 相似文献