Multiaxial stress creep rupture mechanisms of AZ31 magnesium alloy

The maximum principal stresses, von Mises effective stresses and principal facet stresses at the time of creep rupture were compared in uniaxial, biaxial, and triaxial stress states for AZ31 magnesium alloy. The creep rupture of this alloy was experimentally controlled by cavitation, which was the result of a low damage tolerance, λ. Creep deformation could be correlated with the von Mises effective stress parameter. The failure-mechanism control parameter governing the stress state coincided with the experimental results of the rupture of the materials under multiaxial stress states. Finally, the theoretical prediction based on constrained cavity growth and continuous nucleation agreed with the experimental rupture data to within a factor of three.     

Implementation of discharging/charging current sensorless state-of-charge estimator reflecting cell-to-cell variations in lithium-ion series battery packs

This paper offers novel insights to the design and implementation of an innovative state-of-charge (SOC) estimator for the lithium-ion (Li-Ion) series battery pack. The most interesting feature of this approach is that it can utilize information from each filtered terminal voltage of the Li-Ion cells connected in series for SOC estimation of the battery pack. Without actual sensing each discharging/charging current (DCC) applied to the Li-Ion cells, it is possible to extract each DCC estimation from the corresponding filtered terminal voltages with an equivalent electrical circuit model (EECM) identification of all Li-Ion cells in the battery pack. There are two advantages to SOC estimation of the battery pack with this approach. First, the proposal can be implemented simply and effectively, reducing the computational steps required for SOC estimation. By reducing computational steps, the proposal is expected to be more cost-effective. Second, the approach guarantees an improved SOC performance, even if the battery pack results in inevitable cell-to-cell variation among Li-Ion cells. Accordingly, there are fewer differences to previously estimated DCCs among Li-Ion cells. Specifically, all values from the estimated DCCs are properly compensated for by simultaneous parameter modification according to each cell’s electrochemical characteristics. Experimental results clearly demonstrate that our DCC sensorless SOC estimator provides robust SOC performance for the battery pack. This approach considered an experimental battery pack (12S1P) connected in series using 2.6 Ah LiCoO2 cells produced by Samsung SDI.     

Systematic budget allocation for transportation construction projects: a case in Taiwan

It has always been a daunting task for any government to allocate the budgets for public infrastructure effectively so as to maximize the benefits of the limited resources. The most important contribution this paper makes is to conduct an empirical study of the budget allocations of the six region-based road system construction plans in northern Taiwan using the transportation budget allocation model devised in this paper. After reviewing the results, the experts consulted while preparing this paper believe that these results are both objective and able to meet the actual requirements. The competent authority also believes that they are better than those obtained using their original approach. In particular, the construction of this model takes into consideration the highest-level supervisors. To a certain degree, it caters for the practices in budget allocation so that the managers are able to assume the authority corresponding to their responsibility concerning management efficiency and final outcomes.     

Experimental study on a model azimuthing podded propulsor in ice

The objective of this study was to investigate the performance of a model azimuthing podded propulsor in ice-covered water. Model tests were carried out with two different depths of cut into the ice (15 and 35 mm), two different ice conditions (presawn and pack ice conditions), and four different azimuthing angles. The depth of cut is the maximum penetration depth of the propeller blade into the ice block. The 0.3-m-diameter model propeller was operated in a continuous ice milling condition. Ice loads were measured by several sensors which were installed in various positions on the model. Six one-axis pancake-style load cells on the top of the model measured the global loads and two six-component dynamometers were installed on the shaft to measure the shaft loads. One six-component dynamometer was attached to the one of the propeller blades inside the hub to measure the blade loads. The pod unit and propeller performance in ice are presented. Ice-related loads, which were obtained when the blade was inside the ice block, are introduced and discussed. During the propeller–ice interaction, a blade can experience the path generated by the previous blade, which is called the shadowing effect. The effects of shadowing, depth of cut, azimuthing angle, and advance coefficient on propulsor performance are presented and discussed.     

Investigation of ship waves in a narrow channel

This paper presents a discussion of the characteristics of ship waves in a narrow channel restricted by vertical walls, based on observed data and the results computed by a 2-D model. In the numerical model, the propagation of waves generated by a moving ship is simulated by solving 2-D depth-integrated Boussinesq equations. To get the boundary conditions at the location of the ship, the slender-ship approximation is employed. A field observation was carried out at a straight length of navigation channel. The ships targeted in the observations are two kinds of waterbuses with lengths of 28 and 24 m. The relative depth Froude number for the river current, an appropriate parameter for assessing the influence of the current on ship wave characteristics in a navigation channel, ranged from 0.47 to 0.76. The observed maximum wave height varied between 0.13 and 1.26 m. The maximum wave height of the wave train is sharply increased when the relative depth Froude number exceeds 0.6. The results computed by the present model agree fairly well with the observed data.     

Trip generation of vulnerable populations in three Canadian cities: a spatial ordered probit approach

This paper provides an analysis of trip generation of three vulnerable groups: single-parent families, low income households, and the elderly. It compares the mobility of these groups to that of the general population in three Canadian urban areas of Hamilton, Montreal and Toronto, based on data from large-sample metropolitan transport surveys. An ordered probit model with spatially expanded coefficients is used for the analysis. Spatial expansion shows that there are spatial mobility trends for elderly populations and low-income populations even after socio-economic attributes are accounted for. Such spatial differences are not generally found for single parent families. This novel spatial analysis provides clues as to where vulnerable populations may experience greater degrees of social exclusion. It provides information to help prioritize transportation infrastructure projects or other social programs to take into account the needs of vulnerable populations with the lowest levels of mobility.     

基于SPH方法的波浪对水平板冲击的数值模拟(英文)

A numerical model was established for simulating wave impact on a horizontal deck by an improved incompressible smoothed particle hydrodynamics (ISPH). As a grid-less particle method, the ISPH method has been widely used in the free-surface hydrodynamic flows with good accuracy. The improvement includes the employment of a corrective function for enhancement of angular momentum conservation in a particle-based calculation and a new estimation method to predict the pressure on the horizontal deck. The simulation results show a good agreement with the experiment. The present numerical model can be used to study wave impact load on the horizontal deck.     

Strong bottom–up effects on phytoplankton community caused by a rainfall during spring and summer in Sagami Bay,Japan

To assess the consequences of bottom-up effects on phytoplankton community composition during the rainy season, phytoplankton levels and environmental factors were monitored daily from 12 April to 22 July 2003 in Sagami Bay, Japan. The relevant environmental factors were analyzed using cross-correlation analyses. Based on time-series analysis, low surface salinity conditions lasting 0 or 2 days after heavy rainfalls resulted in significant nutrient loading, such as dissolved inorganic nitrogen (DIN), into the coastal area. Also, Chlorophyll-a (Chl-a) concentration frequently increased 2 and 6 days after rainfall. Based on the high total Chl-a concentration, the time was divided into three periods, from 1 to 11 May (Period A), 26 May to 9 June (Period B) and 30 June to 22 July (Period C). The phytoplankton assemblages during Period A were dominated by two dinoflagellates, Ceratium furca and Ceratium fusus. Prior to these species blooming, the heterotrophic dinoflagellate Noctiluca scintillans was dominant. During Period B, the phytoplankton communities were dominated primarily by the diatoms Rhizosolenia delicatula, Hemiaulus sinensis and Navicula spp. Finally, Cerataulina dentata, Rhizosolenia spp., Lauderia borealis and Neodelphineis pelagica were dominant during Period C. After increases in phytoplankton abundance, available nitrogen (N) and phosphorous (P) were consumed and exhausted, which were considered a potential cause of the shift in the dominant organisms from large diatoms to pico- and nano-plankton in the low Chl-a environment. In particular, silicate (Si) was not a major limiting factor for phytoplankton production, since the Si:DIN and Si:P ratios clearly demonstrated that there were no any potential stoichiometric Si limitations, and almost all silicate concentrations were > 2.0 µM during this study. Our results reveal that nutrient sources supplied by river discharge are a main cue for strong bottom–up effects on algal bloom succession during the early summer season in Sagami Bay.     

An investigation of the performance of an electronic in-line pump system for diesel engines

WIT Electronic Fuel System Co., Ltd. has developed a new fuel injector, the Electronic In-line Pump （EIP） system, designed to meet China＇s diesel engine emission and fuel economy regulations. It can be used on marine diesel engines and commercial vehicle engines through different EIP systems. A numerical model of the EIP system was built in the AMESim environment for the purpose of creating a design tool for engine application and system optimization. The model was used to predict key injection characteristics under different operating conditions, such as injection pressure, injection rate, and injection duration. To validate these predictions, experimental tests were conducted under the conditions that were modeled. The results were quite encouraging and in agreement with model predictions. Additional experiments were conducted to study the injection characteristics of the EIP system. These results show that injection pressure and injection quantity are insensitive to injection timing variations, this is due to the design of the constant velocity cam profile. Finally, injection quantity and pressure vs. pulse width at different cam speeds are presented, an important injection characteristic for EIP system calibration.     

Creep Life Prediction of Alloy 718 for Automotive Engine Materials

This study was carried out to investigate the creep life at the high temperature of the Alloy 718 for automotive engine components using the initial strain parameter method (ISPM). Creep tests have performed at elevated temperatures in the range of 550 oC to 700 oC in this work. We also carried out constant stress creep tests. The initial strains were measured during 1 minute after loading. Both the creep stress and rupture time depend on the initial strain. We calculated the creep life of Alloy 718 by using the creep life prediction equations obtained from the ISPM. Then, we compared the creep life predicted by the ISPM to the Larson-Miller parameter (LMP). The experimental rupture time and the calculated rupture time by using the ISPM agreed with a confidence level of 95 %. The creep life predicted by using the ISPM was in very good agreement with the creep life predicted using the LMP method.