Links between subjective and objective evaluations regarding the steering character of automobiles

This work presents an experiment on the relationships between subjective and objective evaluations of vehicle handling. Ten cars were examined objectively in several open-loop driving dynamics manoeuvres and subjectively by test persons in typical traffic situations. Results are extracted from a stationary test (the Slowly Increasing Steer Test), and a dynamical test (the Frequency Response Test). The subjective measurements are obtained from drivers on a rural road course via a questionnaire, which was developed to separately investigate the quantity level perception, the so-called “Niveau”, and the more qualitative “Liking”. These subjective “measurements” are embedded into a two-channel definition of “Steering Comfort” as a genus for “Steering Discomfort” and “Character”. The article concentrates on developing a statistical method for the consideration of correlations amongst the subjective/objective data. In doing so, the variance in example subjective Niveau ratings can be significantly explained by several objective quantities. Indicators for co-domains of validated discomfort characteristics and hints for endeavouring character Liking ranges are detected.     

Thermal design of automobile exhaust based thermoelectric generators: Objectives and challenges

The potential for thermoelectric power generation (via waste heat recovery onboard automobiles) to displace alternators and/or provide additional charging to a vehicle battery pack has increased with recent advances in thermoelectric material processing. In gasoline fueled vehicles (GFVs), about 40% of fuel energy is wasted in exhaust heat, while a smaller amount of energy (30%) is ejected through the engine coolant. Therefore, exhaust-based thermoelectric generators (ETEG) have been a focus for GFV applications since the late 1980s. The conversion efficiency of modern thermoelectric materials has increased more than three-fold in the last two decades; however, disputes as to the thermal design of ETEG systems has kept their overall efficiency at limited and insufficient values. There are many challenges in the thermal design of ETEG systems, such as increasing the efficiency of the heat exchangers (hot box and cold plate), maintaining a sufficient temperature difference across the thermoelectric modules during different operating conditions, and reducing thermal losses through the system as a whole. This paper focuses on a review of the main aspects of thermal design of ETEG systems through various investigations performed over the past twenty years. This paper is organized as follows: first, the construction of a typical ETEG is described. The heat balance and efficiency of ETEG are then discussed. Then, the third section of this paper emphasizes the main objectives and challenges for designing efficient ETEG systems. Finally, a review of ETEG research activities over the last twenty years is presented to focus on methods used by the research community to address such challenges.     

Effect on friction of engine oil seal with engine oil viscosity

Low viscosity engine oil can improve a vehicle’s fuel economy by decreasing the friction between the engine components. Frictional torque varies with the velocity change due to different viscosity characteristics of SAE grade 5W-20, 5W-30 and 5W-40 engine oils. The viscosity for each of these grades was measured to outline the effect low viscosity engine oils have on engine friction, which may lead to improved fuel economy. Engine oil seal frictional torque increases with the shaft rotational speed for all three engine oil grades. A decrease in engine oil seal frictional torque was confirmed when low viscosity engine oil was used. Also, the leak-free performance of the engine oil with the seal satisfied the life limit durability test criteria. Thus, low viscosity engine oil may be used to improve fuel economy by decreasing the frictional loss of the engine oil seal while having no negative impact on performance due to leak-free functioning.     

Analysis process of a steering system using a concept model for idle vibration

This paper describes the development of an optimal design process for a steering column system and supporting system. A design guide is proposed at the initial concept stage of the development process to obtain sufficient stiffness of the steering system while reducing the idle vibration sensitivity of the system. Case studies on resonance isolation are summarized, where vibration modes among the systems are separated by applying a vibration mode map at the initial stage of the design process. This study also provides design guidelines for an optimal dynamic damper system using a CAE (computer aided engineering) analysis. The damper FE (finite element) model is added to the vehicle model to analyze the relation between the frequency and the sensitivity of the steering column system. This analysis methodology makes it possible to achieve target performance in the early design stage and reduction of damper tuning activity after the proto car test stage. Through the proposed steering column system development process, a lightweight vehicle with high stiffness is possible prior to the proto build stage. Furthermore, the improved process is expected to contribute to reducing the overall development period and the number of proto car tests necessary to achieve the desired steering system performance.     

Desired yaw rate and steering control method during cornering for a six-wheeled vehicle

This paper proposes a steering control method based on optimal control theory to improve the maneuverability of a six-wheeled vehicle during cornering. The six-wheeled vehicle is believed to have better performance than a four-wheeled vehicle in terms of its capability for crossing obstacles, off-road maneuvering and fail-safe handling when one or two of the tires are punctured. Although many methods to improve the four-wheeled vehicle’s lateral stability have been studied and developed, there have only been a few studies on the six-wheeled vehicle’s lateral stability. Some studies of the six-wheeled vehicle have been reported recently, but they are related to the desired yaw rate of a four-wheeled vehicle to control the six-wheeled vehicle’s maneuvering during corning. In this paper, the sideslip angle and yaw rate are controlled to improve the maneuverability during cornering by independent control of the steering angles of the six wheels. The desired yaw rate that is suitable for a six-wheeled vehicle is proposed as a control target. In addition, a scaled-down vehicle with six drive motors and six steering motors that can be controlled independently is designed. The performance of the proposed control methods is verified using a full model vehicle simulation and scaled-down vehicle experiment.     

Lane-following method for high speed autonomous vehicles

This paper presents a steering control method for lane-following in a vehicle using an image sensor. With each image frame acquired from the sensor, the steering control method determines target position and direction, and constructs a travel path from the current position to the target position either as an Arc-path or S-path. The steering angle is calculated from the travel path thus generated, and the vehicle follows the travel path via motor-control. The method was tested using a vehicle dubbed as KAV (Korea Autonomous Vehicle) along an expressway (Seoul Inner Beltway) trajectory with a variety of radii (50 m ∼ 300 m) while traveling at a speed of 60 km/h to 80 km/h. Compared with an experienced human driver, the method showed little much difference in performance in terms of lane-center deviation. The proposed method is currently employed for high speed autonomous driving as well as for stop and go traffic.     

Automotive structure vibration with component mode synthesis on a multi-level

The recursive component mode synthesis method (RCMS) has been implemented for the finite element analysis model of an automobile structure as an efficient free vibration analysis tool. The RCMS method is intended to obtain a better performance relative to the block Lanczos method, which is a traditional method in the industry of obtaining eigenvalues, while obtaining the acceptable accuracy. A numerical example of the automobile finite element model demonstrates the outstanding performance of RCMS compared to the block Lanczos method.     

Public perceptions of the use of dynamic message signs

Intelligent transportation systems have been promoted as a means to improve both the efficiency and safety of the road network. The effectiveness of advanced technologies in improving road safety has been an area of research which has thus far yielded mixed results. In order to ensure that advanced technologies deliver on their intended outcomes, more research has to be devoted to understanding road users' perceptions and reactions to these systems. This study examines drivers' perceptions of the use of dynamic message signs and their self‐reported reactions to the messages displayed. In general, drivers support the use of highway electronic boards for traffic incident reports and weather information which have an impact on traffic delays and level of service. They also think that it is a good idea to display road safety messages and to remind drivers to drive safely and be courteous on the roads. Moreover, most drivers reported that they do read and think about the messages displayed and react positively to some of the road safety messages.     

Deconstructing development density: Quality, quantity and price effects on household non-work travel

Smart growth and transit-oriented development proponents advocate increasing the density of new land development and infill redevelopment. This is partly in order to reduce auto use, by reducing distances between trip origins and destinations, creating a more enjoyable walking environment, slowing down road travel, and increasing the market for transit. But research investigating how development density influences household travel has typically been inadequate to account for this complex set of hypotheses: it has used theoretically unjustified measures, has not accounted for spatial scale very well, and has not investigated potentially important combinations of measures. Using data from a survey of metropolitan households in California, measures of development density corresponding to the main hypotheses about how density affects travel—activity density affecting distance traveled, network load density affecting the speed of auto travel, and built form density affecting the quality of walking—are tested as independent variables in models of auto trip speed and individual non-work travel. Residential network load density is highly negatively correlated with the speed of driving, and is also highly correlated with non-work travel, both singly and in combination with other measures. Activity density and built form density are not as significantly related, on their own. These results suggest that denser development will not influence travel very much unless road level-of-service standards and parking requirements are reduced or eliminated.     

Passengers’ willingness to pay for airport ground access time savings

There are cases when passengers are willing to pay a premium to reduce the travel time, in particular when the trip has to be made. This paper aims to provide insight into factors that determine passengers’ willingness to pay to reduce travel time for their ground access to an airport. A methodology is developed that comprises two steps: the identification of the passengers with zero willingness to pay and from the rest the estimation of the additional price they are willing to pay to reduce their travel time. For the first step a Probit model was formulated and for the second a linear regression model. To this purpose, data has been collected employing stated preference from passengers at the Athens International Airport. It has been found that a high percentage of passengers have zero willingness to pay, and of the remaining ones those using public transport have a significant willingness to pay to reduce access travel time. The methodology and the models are structured in such a way that their transferability to any airport environment is possible, thus providing a useful tool for decisions relating to airport ground access measures.