Effect of Seismic Parameters on the Safety Factor for an Underground Cavern北大核心CSCD

In order to quantitatively evaluate the safety of the surrounding rock of an underground cavern under seis-mic load, a comprehensive evaluation method for the stability of surrounding rock is proposed based on the general safety factor and point safety factor. A calculation method for the general safety factor of a cavern based on the prin-ciple of shear strength reduction of a rock mass is given, the run-through of the plastic zone between the main power-house and main transformer room is presented as a critical criterion for the overall instability of the cavern, and the general safety factor is obtained by searching for the reduction coefficient. A point safety factor calculation method based on the Mohr-Coulomb yield criterion is given. The influence of different seismic input parameters on the general safety factor of the cavern and the point safety factor of key positions are studied based on an underground power-house cavern of a hydropower station in Southwest China. The results show that the quantitative evaluation method for the stability of the surrounding rock based on the safety factor is feasible and can reflect the general safety de-gree and local safety degree of different positions of the cavern for different working conditions. It is found that the general safety factor of the cavern and the point safety factor of key positions decrease with an increase of the ampli-tude and duration of a seismic wave while they increase with an increase of the incident angle; additionally, the low frequency of a seismic wave has a great influence on the cavern while the high frequency has little effect. © 2018, Editorial Office of "Modern Tunnelling Technology". All right reserved.     

Analysis on the Effects of Overloading on the Mechanical Properties of Tunnel Structures in the Silty Ground --A Case Study of Sutong River-crossing GIL Utility Tunnel北大核心CSCD

Based on the Sutong GIL utility tunnel project, which is constructed by the shield machine under the river, and as for the overloading problem at the river bank slope during operating period, the refined threedimensional finite element model was established to study the deformation and cracking characteristics of the tunnel segment structure under different forms of overloading. The evolution laws of section convergence, joint opening and structural stress were analyzed, and the structure damage mechanisms were revealed under conditions of large area loading and local loading. The surface-surcharge control standard was proposed. For the big diameter shield tunneling crossing the silty clay, the research results show that: (1) the deformation failure process is divided into three stages under large area loading condition, taking the design load and compressive yield of rebars inside haunch as the critical points respectively. The first stage is characterized by the elastic stress, the second stage is in plastic state with fracture, and the third stage is accelerating deformation and instability stage. The vertical convergence is 110.5 mm with no opening of joints when rebars are yielded; (2)the deformation failure process under local loading condition is also divided into elasticity, plasticity and instability stages, taking the design load and tensile yield of rebars outside haunch as the critical points respectively. The vertical convergence is 152.6 mm with joint opening of 4.36 mm; (3) the early-warning values of additional stress on the ground under conditions of large area loading and local loading are 110 kPa and 70 kPa respectively. © 2018, Editorial Office of "Modern Tunnelling Technology". All right reserved.     

“工厂法”沉管隧道早期性能的足尺试验研究

由于沉管隧道管段体积大、结构形式复杂、施工工艺复杂,容易因温度、收缩以及约束等原因,造成管段结构在预制阶段出现危害性裂缝,进而影响结构的服役性能和耐久性能。文章依托在建港珠澳大桥沉管隧道工程实例,开展了足尺试验,对"工厂法"沉管管节关键部位的温度和应变发展实施了监测,分析对比了温度发展规律和应变发展规律。分析结果表明:在早期因混凝土水化热引起温度上升,整个管段结构膨胀受拉,温度到达峰值后逐渐下降,结构也收缩恢复;但由于混凝土自收缩等因素的存在,结构最终收缩受压。研究所提供的试验结果可作为深入进行数值分析的一个基础。     

大断面浅埋偏压隧道CRD法施工工序研究

文章以良村隧道CRD法施工为工程背景,布设了变形监测点及内力测试元件,分析了CRD法施工隧道围岩变形情况及结构内力特征,并对CRD法施工隧道在不同开挖顺序下的开挖过程进行了数值模拟,分析比较了不同开挖顺序时的围岩位移、应力变化情况。结果表明:CRD法对各分部施工工序影响较大,且各分部对拱顶下沉的影响程度从大至小依次为1部、2部、3部和4部;隧道内侧围岩压力大于外侧,钢支撑内力均为压应力,且拱腰位置轴力大于其它部位。比较隧道开挖变形的差异以及结构的受力特点,结合数值分析结果,得出了山体外侧先开挖方案无论在围岩变形还是隧道结构受力方面相比于山体外侧后开挖都较小,安全系数相对较高。因此,合理的施工工序应该是先进行山体外侧开挖并施作初期支护,然后再在山体内侧开挖施工。     

穿越古滑坡川主寺隧道围岩破坏特征及稳定性研究

文章以川主寺隧道所处的工程地质条件为基础,通过现场调研分析了隧道围岩变形破坏形式主要为坍塌、掉块以及剥落.围岩稳定性三维有限元数值模拟结果显示,碎裂围岩自稳能力差,围岩变形以弹塑性变形、松弛变形为主;H型钢拱架支护结构对碎裂围岩稳定性起到积极的作用,并通过典型洞段现场位移监测数据分析结果得以证实.     

基于Bayes判别分析方法的叙岭关隧道溶洞水源识别

基于Bayes判别方法,选取水化学常量组分作为判别指标,利用叙岭关隧道地区9个动态监测点的53个水样样本建立了该地区的水源判别模型.模型检验结果表明,其回判准确率为96.23％,具有较高的识别精度和工程推广能力.利用建立的判别模型,对叙岭关隧道1号溶洞内两个出水点RQ1和RQ2的水源进行了识别,并结合其流量动态变化特征、同位素分析结果,以及1号溶洞发育位置,推断1号溶洞内两个出水点的水源为P1m+q含水层中的岩溶地下水.根据判别结果,建议1号溶洞采取“以排为主”的原则加以处治,并尽量保留溶洞水的过水通道.     

Physical environments influencing bicyclists’ perception of comfort on separated and on-street bicycle facilities

This study investigates the impacts of physical environments on bicyclists’ perceptions of comfort on separated and on-street bicycle facilities. Based on a field investigation conducted in Nanjing, China, we find that physical environmental factors significantly influencing bicyclists’ perception of comfort on the two types of facility. Cyclists’ comfort is mainly influenced by the road geometry and surrounding conditions on physically separated paths while they pay attention to the effective riding space and traffic situations on on-street bicycle lanes.     

桃树坪隧道富水粉细砂地层挑高段设计方案优化

桃树坪隧道穿越富水粉细砂地层,施工难度很大,尤其是斜井进正洞的挑高段施工风险更高.通过对四种方案在施工工序、支护形式及体系转换等方面的比选,最后选择采用导洞爬高进入正洞双侧壁导洞高度进行导洞施工、后进行中间部分施工的设计方案,顺利完成了隧道施工.文章详细介绍了四种比选方案及方案实施效果.     

高速公路ETC车道防邻道及跟车干扰研究

在ETC车道系统中,相邻两个ETC车道之间的OBU与RSU相互影响,RSU与非本车道上的OBU进行通讯并完成交易,引起邻道干扰;工程实施、设备等原因引起跟车干扰,造成ETC收费失败。针对存在的问题,分析工程安装、设备原因,提出切实可行的解决方案,保证ETC车道功能的正确性、完整性,是交通运输行业节能减排绿色发展成果之一。     

地铁隧道管片混凝土免蒸养技术研究及其发展

针对蒸汽养护对混凝土可能产生不可逆转的结构破坏和能耗大的问题,采用聚羧酸外加剂的接枝共聚技术,开发出了超早强型的聚羧酸减水剂,并进行了管片混凝土的制备。结果表明,采用超早强型聚羧酸能明显加速水泥的水化进程,促进早期强度的发展,在低温（10℃～20℃）条件下实现管片混凝土的免蒸养,12h可达到管片拆模吊起所需要的强度,这对降低管片混凝土的生产成本、节约能源具有积极的意义