《电加热道岔融雪系统设备》TB/T3539-2018解读

解读《电加热道岔融雪系统设备》与《客运专线铁路信号产品暂行技术条件汇编——电加热道岔融雪系统设备》标准的共性部分,并从编制背景、标准定位、技术要求、试验方法和检验规则等方面,分析两者之间的差异性.     

线路支承状态变化对轨道动态特性的影响

把温度力作用下的无缝线路简化为纵向力作用的弹性等间距支承的无限长均匀梁结构,通过连续梁理论,建立了纵向力作用下无缝线路钢轨的振动模型.分析了轨道结构钢轨自振频率与其纵向力间的内在关系,分别讨论了钢轨在承受纵向拉力和纵向压力时自振频率的变化特征,比较了钢轨类型改变、钢轨支承间距变化后对上述变化的影响.结果表明:纵向拉力作用下钢轨的竖向自振频率会随着拉力的增加而增大,钢轨支承间距加大会降低其自振频率;纵向压力作用下,钢轨的竖向自振频率随着压力的增加而减小;第一振型变化趋势基本分为两个阶段,当轴向压力较小时,呈线性变化,随着轴向压力的不断增加,逐渐地产生了非线性的变化;二阶及以上振型变化与受拉状态相似.     

南京地铁1号线的气体灭火设计

结合南京地铁1号线的工程设计,将七氟丙烷(HFC-227)气体消防工程设计中经常遇到的一些问题,如管网设计距离、系统管网的管道内容积、七氟丙烷的喷放时间等,在满足技术规范要求的前提下所采取的解决方案做了阐述.这些方法的使用大大缩短了工程设计时间.介绍了南京地铁1号线报警灭火系统的结构,气体灭火系统与车站火灾报警系统的通信方案.     

城市公共交通多元票制初探

借鉴国外先进经验,引进多元化公交票制是国内推进公交优先发展的重要措施.多元票制,即将乘客进行科学的分类,根据乘客的出行需求,设置不同种类的车票,以提高公交吸引力.就国内公交发展现状来看,换乘优惠的票制改革是推广多元票制的最佳切入点.     

Virtual prototype simulation on underwater hydraulic impingement shovel

The virtual prototype technology is applied to the design of the hydraulic impingement shovel, which is to increase the reliability of the design. The work principle of hydraulic impingement shovel is expatiated, and its dynamic equations are established. The 3D model of virtual prototype is built by PRO/E. Then the couple between the mechanical body of prototype and the hydraulic system is completed by virtue of ADAMS. Finally, the simulation is made on the virtual prototype. The simulation results show that the design of underwater hydraulic impingement shovel is rational. The virtual prototype technology could lay sound foundation of successful manufacturing of physical prototype for the first time and offer highly effective and feasible means for the design and production of underwater equipments.     

Experimental study on the width of the turbulent area around bridge pier

At present, the method of calculating the turbulent flow width around the bridge pier is not given in the "Standard for Inland River Navigation" (GB50139-2004) in China, and the bridge designer usually increases the bridge span in order to ensure the navigation safety, which increases both of the structural design difficulty and the project investments. Therefore, it is extremely essential to give a research on the turbulent flow width around the bridge pier. Through the experiments of the fixed bed and the mobile bed, the factors influencing the turbulent flow width around the bridge pier have been analyzed, such as the approaching flow speed, the water depth, the angles between the bridge pier and the flow direction, the sizes of bridge pier, the shapes of the bridge pier, and the scouring around the bridge pier, etc. Through applying the dimension analytic method to the measured data, the formula of calculating the turbulent flow width around the bridge pier is then inferred.     

A second order volume of fluid （VOF） scheme for numerical simulation of 2-D breaking waves

Among all environmental forces acting on ocean structures and marine vessels, those resulting from wave impacts are likely to yield the highest loads. Being highly nonlinear, transient and complex, a theoretical analysis of their impact would be impossible without numerical simulations. In this paper, a pressure-split two-stage numerical algorithm is proposed based on Volume Of Fluid (VOF) methodology. The algorithm is characterized by introduction of two pressures at each half and full cycle time step, and thus it is a second-order accurate algorithm in time. A simplified second-order Godunov-type solver is used for the continuity equations. The method is applied to simulation of breaking waves in a 2-D water tank, and a qualitative comparison with experimental photo observations is made. Quite consistent results are observed between simulations and experiments. Commercially available software and Boundary Integral Method (BIM) have also been used to simulate the same problem. The results from present code and BIM are in good agreement with respect to breaking location and timing, while the results obtained from the commercial software which is only first-order accurate in time has clearly showed a temporal and spatial lag, verifying the need to use a higher order numerical scheme.     

Using a SVM to evaluate damage to vibration isolators in an elastic raft system

Predicting damage to vibration isolators in a raft experiencing heavy shock loadings from explosions is an important task when designing a raft system. It is also vital to be able to research the vulnerability of heavily shocked floating rafts unreliable, especially when the allowable values The conventional approach to prediction has been or ultimate values of vibration isolators of supposedly uniform standard in a raft actually have differing and uncertain values due to defective workmanship. A new model for predicting damage to vibration isolators in a shocked floating raft system is presented in this paper. It is based on a support vector machine（SVM）, which uses Artificial Intelligence to characterize complicated nonlinear mapping between the impacting environment and damage to the vibration isolators. The effectiveness of the new method for predicting damage was illustrated by numerical simulations, and shown to be effective when relevant parameters of the model were chosen reasonably. The effect determining parameters, including kernel function and penalty factors, has on prediction results is also discussed. It can be concluded that the SVM will probably become a valid tool to study damage or vulnerability in a shocked raft system.     

某车型潮湿环境下制动抱死问题整改研究

为解决某车型售后用户抱怨在汽车刚开始行驶时(冷启动,尤其每天早晨)的后轮制动抱死问题,分析可能造成潮湿环境下后轮制动抱死的原因。通过分析试验得出:鼓式制动器的摩擦片材料锈粘着问题是导致潮湿环境下制动抱死的主要原因。     

CATIA VBA二次开发在装配中批量搜索零件的应用

文章针对汽车开发过程中,经常需要对部分特定的零件进行批量选择用于校核或者作为报告用图,给出了装配中对指定的多个零件进行程序搜索选定的方法。在介绍VB编程语言及CATIA二次开发理论的基础上,给出程序自动搜索零件的基本流程,利用CATIA Automation调用Search方法,实现零件的批量搜索。通过实例验证,证明了CATIA批量搜索的优越性。结果表明,CATIA二次开发可以提高工作效率。