Combustion development of a Bi-Fuel engine

Environmental improvement and energy issues are increasingly becoming more important as worldwide concerns. Natural gas is a good alternative fuel that can help to improve these issues because of its large quantity and clean burning characteristics. This paper provides the experimental performance results of a Bi-Fuel engine that uses Compressed Natural Gas as its Primary fuel and gasoline as its secondary fuel. This engine is a modification of the basic 1.4-liter gasoline engine. Generally, on the unmodified base engine, torque and power for CNG fuel are considerably lower than gasoline fuel. In this paper, the influence of fuels on wall temperature, performance and emissions are investigated.     

New approach for performing failure analysis of fuel cell-powered vehicles

Safety of hybrid-electric and fuel cell vehicles is a critical aspect of these new technologies, since any accident exposing occupants of such vehicles to unconventional hazards may result in significant setbacks to successful market penetration. Fuel cell and hybrid-electric drive systems are complex, and it is essential to perform a thorough analysis to determine critical failure conditions. There are several safety concerns for routine operation of such systems, particularly for hydrogen-fueled vehicles. A modified Failure Modes and Effect Analysis (FMEA) has been developed, along with a Criticality Analysis (CrA), to identify potentially hazardous conditions for crash and non-crash situations. A mathematical model of fuel cell operation has been developed and used here in conjunction with the FMEA. Component failures during the event modes are simulated using vehicle models developed with Matlab Simulink tools. Six simulation models were created using the software. In addition, a preliminary finite element model of a fuel cell vehicle, using a Ford Taurus (91′) model year sedan, has been developed and implemented. This finite element model is used as a demonstration of the crash simulation of the vehicle.     

Tests on ultimate strength of hull box girders made of high tensile steel

The experimental results of the collapse of three box girders subjected to pure bending moment are presented. The structures are made of high tensile steel of 690 MPa of nominal yield stress reinforced with bar stiffeners of the same material. The moment curvature curves are presented covering the pre- and post-collapse regions. The modes of collapse for each box girder are discussed considering the variation on the panel's slenderness. The concept of efficiency of high tensile steel structures is introduced. The concept is very useful to identify the governing parameters affecting the ultimate strength of 3D structures under predominant bending moment.     

Cost-time Minimization in a Transportation Problem with Fuzzy Parameters: A Case Study

In real world applications the supply, the demand and the transportation cost per unit of the quantities in a transportation problem are hardly specified precisely because of the changing economic and environmental conditions. It is also important that the time required for transportation should be minimum. In this paper a method has been proposed for the minimization of transportation cost as well as time of transportation when the demand, supply and transportation cost per unit of the quantities are fuzzy. The problem is modeled as multi objective linear programming problem with imprecise parameters. Fuzzy parametric programming has been used to handle impreciseness and the resulting multi objective problem has been solved by prioritized goal programming approach. A case study has been made using the proposed approach.     

Development of models for predicting roadside nitrogen dioxide concentrations and their evaluation against datasets measured in Dublin,Ireland

Different methods for predicting levels of roadside NO₂ from NO_x concentrations have been proposed. Prior work suggests that either a linear or a logarithmic relationship exists among the roadside NO₂ and NO_x concentrations. We modify and compare those methods with new formulations based on the principles of the original methods for datasets pertaining to Dublin. A new relationship based on the power law is developed to better model the decay of the ratio of (NO₂/NO_x)_road ratio with increasing NO_x concentration. These formulations are compared and examined at two study sites: at an intermittently congested urban street canyon and a free-flowing motorway.     

Assessing the CO2 impact of current and future rail track in the UK

This paper investigates the CO₂ impact of current and future UK rail track and estimates the material, process and transport emissions associated with construction, maintenance and end-of-life activities for designs at high and low traffic loads. Analysis shows that for current track configurations, track with concrete sleepers has the lowest CO₂ impact, followed by steel, hardwood and softwood. Several potential future rail track designs have been analysed including embedded rail and double and quadruple-headed rail. All future track designs have a lower impact than current designs, but this improvement is more marked at high traffic loads. Up to a 40% reduction in CO₂ impact could be achieved if the UK rail network was to move from conventional track design to a double-headed embedded rail design. Key levers for reducing the CO₂ impact of track are identified as service life extension, traffic load reduction and the selection of low impact track designs.     

Off-set crack propagation analysis under mixed mode loadings

An assessment was carried out herein to study the eccentricity of cracks subjected to mixed-mode loadings. Several loading locations relative to a central line were selected to induce mixed-mode loadings, which were computed using a finite element method. An adaptive meshing technique was adopted during the simulation of crack propagation to ensure the singularity of stress at the tip of the crack. The stress intensity failure criterion was used and programmed, and the node splitting technique was used when the stress intensity factor reached the fracture toughness of the material to simulate crack propagations. It was found that large variations in the stress intensity factor were observed when off-set cracks were used, and that K _II decreased when loading distance increased, but increased when the off-set crack distance was increased. Both crack eccentricity and loading distance played important roles in producing mixed-mode loading, compared to the influence of central cracks. Correction factors were introduced to modify the calculation of stress intensity factors under mixed-mode loadings. Simulations of crack propagation were also conducted to study the effects of crack eccentricities and loading distances. It was found that the crack length, the loading distance relative to the central crack and the crack eccentricity dominated calculations of the integrity of cracked structures.     

Sampling of alternatives for route choice modeling

This paper presents a new paradigm for choice set generation in the context of route choice model estimation. We assume that the choice sets contain all paths connecting each origin–destination pair. Although this is behaviorally questionable, we make this assumption in order to avoid bias in the econometric model. These sets are in general impossible to generate explicitly. Therefore, we propose an importance sampling approach to generate subsets of paths suitable for model estimation. Using only a subset of alternatives requires the path utilities to be corrected according to the sampling protocol in order to obtain unbiased parameter estimates. We derive such a sampling correction for the proposed algorithm.Estimating models based on samples of alternatives is straightforward for some types of models, in particular the multinomial logit (MNL) model. In order to apply MNL for route choice, the utilities should also be corrected to account for the correlation using, for instance, a path size (PS) formulation. We argue that the PS attribute should be computed based on the full choice set. Again, this is not feasible in general, and we propose a new version of the PS attribute derived from the sampling protocol, called Expanded PS.Numerical results based on synthetic data show that models including a sampling correction are remarkably better than the ones that do not. Moreover, the Expanded PS shows good results and outperforms models with the original PS formulation.