Deflection test and transmission error measurement to identify hypoid gear whine noise

T-Hypoid gears are commonly used in rear-drive and 4WD (4 Wheel Drive) vehicle axles. Investigating their sensitivity to deflections is one of the most important aspects of their design and optimization procedures. Therefore, a deflection test was performed in this study in the actual gear mounting using completely processed gear. This test covered the full operating range of gear loads from “no load” to “peak load”. Under peak load, the contact pattern extended to the tooth boundaries without showing a concentration of the contact pattern at any point on the tooth surface. The transmission error was tested under an axle assembly triaxial-real-car-load condition.     

Development of a navigation algorithm with dead reckoning for unmanned ground vehicles

A navigation algorithm is indispensable for Unmanned Ground Vehicles (UGVs). During driving, UGVs follow a global path. In this study, we propose a navigation algorithm using Real Time Kinematic (RTK)-Differential Global Positioning System (DGPS) units and encoders to complement global path planning. Sometimes GPS systems lose their signals and receive inaccurate position data due to many factors, such as edifice and barrier obstructions. This paper shows that GPS deviations can be solved using a Dead Reckoning (DR) navigation method with encoders and that position errors can be decreased through the use of RTK-DGPS units. In addition to this method, we will introduce a new waypoint update algorithm and a steering algorithm using RTK-DGPS units.     

Modified lateral control of an autonomous vehicle by look-ahead and look-down sensing

This paper presents a modified lateral control method for an autonomous vehicle with both look-ahead and look-down sensing systems. To cope with sensor noise and modeling uncertainty in the lateral control of the vehicle, a modified LMI-based H lateral controller was proposed, which uses the look-ahead information of the lateral offset error measured at the front of vehicle and the look-down information of the vehicle yaw angle error between the reference lane and the centerline of the vehicle. To verify the safety and the performance of the lateral control, a scaled-down vehicle was developed, and the positioning of the vehicle was estimated with USAT. The proposed controller, which uses both look-ahead and look-down information, was tested for lane changing and reference lane tracking with both simulation and experiment. The simulation and experimental results show that the proposed controller has better tracking and handling performance compared with a controller that uses only the look-ahead information of the target heading angle error.     

License plate extraction method for identification of vehicle violations at a railway level crossing

The primary cause of most railroad accidents is vehicle entry into railway level crossings despite warning messages. To identify drivers who violate railway level crossing regulations, vehicle license plate recognition can be applied at railway level crossings. The purpose of this paper is to present an effective method for extracting the license plate region from vehicle images taken at railway level crossings. The method proposed in this paper uses the variation in the gray-level values across the image of a license plate. For license plate region extraction, the character region is first recognized by identifying the character width and the difference between the background region and the character region. The license plate region is then extracted by finding the inter-character distance in the plate region. In addition, the license plate type is identified by the difference in the gray-level value between the background region and the character region. The proposed method is effective in solving the current challenges in extracting the license plate region from the damaged frames of license plates issued for domestic use, including new types of license plates. According to the experimental results, the proposed method yields a high extraction rate of 99.5% for vehicle license plates.     

Design framework for FlexRay network parameter optimization

Because the FlexRay protocol has more than 70 configuration parameters and these parameters correlate with each other, designing a FlexRay network is a complex and difficult task. In this study, we propose a design framework that optimizes the two main FlexRay network parameters that are highly relevant to the application algorithm. The design process is composed of two steps for optimizing parameters. In the first step, the static slot length is optimized using a frame-packing algorithm. This algorithm binds network signals into static frames based on their periods and signal groups. In the second step, the communication cycle length is optimally designed with frame-scheduling algorithm and worst-case reponse time analysis. Based on the frame-scheduling algorithm, the response times are analyzed. The proposed design framework was applied to a unified chassis control system as a case study, and the analytical results were verified.     

Comprehensive lateral driver model for critical maneuvering conditions

A new comprehensive driver model is presented for critical maneuvering conditions with more accurate dynamic control performance. In order to achieve a safe maneuvering mode, a new path planning scheme to maintain stability of the vehicle was designed. A new steering strategy, considering the errors of vehicle position and yaw angle between the real track and the planned path, was established to obtain the steering angle. Therefore, the vehicle can be adjusted to accurately follow the desired path with the driver model, and the stability of the vehicle and the smoothness of the steering angle input were comprehensively considered. Simulation results were used to validate the control performance in comparison with the optimal preview driver model proposed by Macadam.     

Advance-F automatic car-following model and its traffic characteristics

This study develops a longitudinal control model for automatic car-following with one switch and two controllers. The switch is operated using fuzzy logic to activate acceleration or trigger braking. The two controllers activate the acceleration pedal and the brake system and use reference adaptive control theory. A simulation is utilized to evaluate the acceptability of the proposed model and to compare the traffic characteristics between machine driving (by the proposed model) and human driving (as represented by the GM-V model). The simulation results indicate that this model is acceptable and is both safe and efficient for use in traffic. However, the automatic car-following system is more aggressive than humans are, which may be the primary challenge in implementation.     

Engine performance and toxic gas analysis of biobutanol-blended gasoline as a vehicle fuel

A comprehensive study evaluating the performance of biobutanol-blended gasoline in passenger cars was conducted because biobutanol is considered a better biofuel than bioethanol as it has no water solubility and it has a higher caloric value, giving it a higher energy value. Several kinds of samples—suboctane gasoline, 8 volume percentage and 16 volume percentage biobutanol—blended gasoline, and a 10 volume percentage MTBE-blended market sample (as the oxygencontaining gasoline)-were tested to evaluate the engine performance in terms of the detergency of the intake valves and combustion chambers, power, emissions, and fuel efficiency. Additionally, the toxicity of the emissions from these biobutanolblended samples was tested in order to assess the viability of biobutanol as one of the competitive potential substitutes for MTBE as an oxygenator in the near future. The results show that biobutanol-blended gasoline samples had relatively better detergency, relatively higher power, and similar levels of emissions compared with those of MTBE-blended gasoline. Formaldehyde was emitted from all of the samples at almost the same levels and within the error range, whereas biobutanolblended gasoline samples emitted approximately three times the amount of acetaldehyde than did the suboctane gasoline. This study shows that biobutanol is one of the best alternative bioalcohol fuels for use in the near future.     

Quality evaluation of car window motors using sound quality metrics

In this paper, a method to establish a decision criterion to evaluate the quality of small window motors using sound quality (SQ) metrics is suggested. Although the sound level radiated from the motor is relatively small compared to other sounds in a car, the sound from an abnormal motor gives an uncomfortable feeling and the impression of abnormal operation, which can lead to customer complaints. To construct an objective decision criterion, the correlation between the SQ metrics and the subjective decision on the passing or failure of the motor were investigated. Four representative SQ metrics, viz., loudness, sharpness, roughness, and fluctuation strength, were calculated for the collected samples. It was observed that the loudness and roughness of the motor sample group classified as abnormal was higher than those of the normal motors. For a single figure rating for motor quality, an evaluation index for the motor sound was generated by combining the correlated SQ metrics with proper weightings. Evaluation results on the specimens that were not employed in generating the quality evaluation index showed a reasonable agreement with the subjective test at 73%. The suggested quality check method can replace the current subjective decision procedure to identify the faulty motors.