Comparison study on characteristics of nano-sized particle number distribution by using condensation particle counter calibrated with spray and soot type particle generation methods

In the year 2011, the Particle Measurement Program (PMP) in Europe started the regulation of the diesel vehicle’s nano-sized particle number density (PN) due to its high degree of harm to the human body. Concretely, the standard level of PN emission was introduced in the Euro 5+ and 6 emissions regulation with a limit (<6.0 × 10¹¹#/km) for diesel light-duty vehicle. Therefore, the determination of suitable and sophisticated instruments for reliable particle sampling and analysis was essential in taking exact experimental data. Now, among the PN emission measuring devices suggested by the PMP, condensation particle counter (CPC) is a key equipment for measuring the particle number density in real time and it has been used extensively. However, CPC can cause different results depending on operating conditions of the saturator and condensation that induce different rates of particle growth. This study was conducted to analyze the effect of CPC calibrated by a two-particle generator with spray and soot type methods applied on the nano-sized particle distribution’s parameters such as number concentration and linearity. Also, in order to ensure the reliability for particle sensor system named as PPS, which had emerged as a useful diagnostic to making spatially and temporally resolved quantitative measurements of diesel PN concentration, it was compared with calibrated CPC system. As a result, nano-sized particle measuring system with CPC calibrated by spray type particle generator had a much higher counting efficiency, indicating a larger nano size available than soot type particle generator. And, comparative experimental results on the correlation between the particle number of CPC to a reflectance PPS system showed that above 5,000 #/cm ³ in number concentrations measured by CPC as well as PPS were found to be similar with good linear relationship.     

Impact technique for measuring global dynamic stiffness of engine mounts

Engine mounts are used for engine vibration isolation. The dynamic performance of the mount depends on the orientation. Measurements of the dynamic properties of engine mounts are usually performed in the axial direction because of the problem related to actuator loading direction and set up costs. Impact technique is developed here to measure the dynamic driving point stiffness and driving point shear stiffness of engine mount in a single setup. The compressive and shear frequency-dependent stiffnesses are obtained in the vertical orientation. A transformation matrix is used to calculate the frequency-dependent stiffnesses and loss factors in other orientations. Three different designs of engine mounts are used to verify the accuracy of the transformation model. The correlation coefficient between calculation and measurement results show R²≥ 0.995 along the X- and Y-axes. For the Z-axis, mounts B and C showed R²≥ 0.95 and mount A 0.687 ≤ R²≤ 0.791.     

杭州湾跨海大桥混凝土结构耐久性原位监测预警系统

为了确保杭州湾跨海大桥混凝土结构达到百年设计使用寿命,评价混凝土结构耐久性状况的动态发展,通过对预埋式钢筋腐蚀无损监测传感系统的国际合作研究,确定了基于电化学原理和辅助光纤技术的耐久性监测技术思路,制定了该工程耐久性动态预报监测平台的构架技术方案,捕获了结构各部位腐蚀预警的个性化判据,优化了全桥测点的布置,集成、改良并安装了控制关键部位的全套系统(共计48套监测单元)。工程实测结果表明:测试数据稳定,并且与实验室研究数据吻合。     

不同加载幅值下考虑层间界面条件和侧向剪力作用的柔性铺面响应

该文进行了一个三维有限元参数量化的粘弹性路面响应研究,由于不同的轮胎配置:双轮和宽基轮胎在3种温度(5、25和40℃)和两种速度(8、72 km/h);还有影响路面响应的3种因素:移动车轮荷载幅值(连续,梯形),层间界面条件(简单的摩擦和粘弹性模型)和横向力共同对路面响应的影响进行了研究.研究发现连续加载幅值,不但可以模拟路面对运动轮荷载的响应,并且是一种比目前使用的梯形荷载幅值更准确的研究模型.粘弹性模型极大地提高了双轮胎对预测路面的响应,而简单的摩擦模型更接近宽基轮胎的实地测量.侧向剪力是积极改善预测轮底的表面磨损和底部热拌沥青(沥青)基层的较小程度上的应变.研究表明:使用连续加载幅值和非均匀压力分布模拟移动轮,侧向剪切力和适当的界面摩擦可显著改善有限元模型对车辆加载路面响应的预测能力.     

Experimental study on the impact characteristics of a sandwich composite with an aluminum foam core

The need for composites has been increasing in various industries because composites have good mechanical properties for their weight and superior stiffness and strength. The composites addressed in this study were multi-pore aluminum foam with a specific gravity of 1/10 composed of solid aluminum metal. This composite has excellent impact energy-absorption capability. In this study, impact tests on an aluminum foam core sandwich composite with a porous core were conducted to examine its mechanical properties. The specimen was a sandwich structure with an aluminum foam core, and different impact energies, such as 50J, 70J, and 100J, were applied to the specimen. Consequently, a maximum load of 5.5 kN occurred when the striker penetrated the upper face sheet in all experiments. The maximum load occurred at 4.2 ms for 50J, 3.5 ms for 70J, and 3.0 ms for 100J, indicating that the greater the impact energy was, the shorter the time was until the maximum load. After the maximum load occurred, that is, after the penetration of the upper face sheet, the striker penetrated 10 mm further, causing the core to be damaged in the 50J test, while the lower face sheet remained intact. In the 70J test, the striker penetrated the core and caused damage to the upper face sheet at 10 ms. Finally, in the 100J test, the striker penetrated both the upper face sheet and core and even the lower face sheet at 10 ms. Given the result above, the maximum load occurred when the striker penetrated the upper face sheet and the sandwich composite with aluminum foam core; the load then gradually decreased and then rapidly increased when the striker reached the lower face sheet, and the maximum load lasted slightly longer than the time required for the upper face sheet to be penetrated.     

Dual extended Kalman filter for vehicle state and parameter estimation

The article demonstrates the implementation of a model-based vehicle estimator, which can be used for combined estimation of vehicle states and parameters. The estimator is realised using the dual extended Kalman filter (DEKF) technique, which makes use of two Kalman filters running in parallel, thus 'splitting' the state and parameter estimation problems. Note that the two problems cannot be entirely separated due to their inherent interdependencies. This technique provides several advantages, such as the possibility to switch off the parameter estimator, once a sufficiently good set of estimates has been obtained. The estimator is based on a four-wheel vehicle model with four degrees of freedom, which accommodates the dominant modes only, and is designed to make use of several interchangeable tyre models. The paper demonstrates the appropriateness of the DEKF. Results to date indicate that this is an effective approach, which is considered to be of potential benefit to the automotive industry.     

Modelling of wheels and rail discontinuities in dynamic wheel-rail contact analysis

A classification of wheel-rail contact is given. Difference is made between modelling of a running wheel with continuous single-point-contact, as is common practice in wheel-rail contact analysis, and a wheel with transient double- or multi-point-contact, which may occur for rail irregularities with curvatures larger than that of the wheel circumference. It is shown that application of the first model for these irregularities will strongly underestimate the contact forces as it does not describe occurring mechanisms correctly. Further, it is shown that in principle it is not possible to describe the second type of contact fully correct with a lumped wheel model. Both wheel models are formulated mathematically for some basic contact cases. Afterwards, results are applied to a linear track model. Analytical closed-form solutions are found in the frequency domain for arbitrary type of contact and numerically transformed to the time domain. Finally, the necessity is shown to avoid situations where transient multiple-point-contact may occur (like rail joints) in practice.     

怎样卖掉你的车

在汽车消费发达的国家，二手车消费是整个汽车消费的重要组成部分。甚至可以说，科学、合理、完善的二手车消费体制带动了整个汽车消费的发展。在今天的中国，汽车越来越多地进入了家庭，准备置换手中旧车的人也越来越多，所以《爱车》特别邀请美国二手车销售专家M.Brueggemann先生为中国的车主朋友奉献一篇精彩的文章，虽然本文充满美国社会的气息，很多技巧不能直接套用，但是先进的经验是绝对值得借鉴的。[编者按]     

理解消费者对质量的定义

汽车产品的质量总是会受到巨大的关注。质量较差会导致财务成本的增加,这使得制造商把提升质量作为一项商业必要的手段。过去的数年中有无数方法和流程被用来减少浪费和消除缺陷 (比如6-Sigma法和TQM完全质量管理法)。我们并不缺少这样的衡量工具,来衡量因质量问题和返工而产生的负面经济效益。运用这些衡量工具能够理解质量对每辆车或者公司的盈利能力造成的影响,并且帮助公司取得显著的产品质