Development and Evaluation of a High Voltage Supply Unit for Electrorheological Fluid Dampers

Controllable dampers using electrorheological (ER) fluids have attracted considerable interest in recent years. They are proposed for use in semi-active suspensions for ground vehicles. The main advantages of ER fluid dampers are their fast response, ease of control, simple construction and low power requirements. This paper describes the development and testing of a high-voltage supply unit for modulating the damping force of an ER fluid damper. Experimental results on the vibration isolation characteristics of an ER fluid damper with different control strategies, obtained using a quarter-car model test rig, are also presented.     

The influence of food quality on the nutritional acclimation of the copepod Acartia clausi

The influence of food quality on the nutritional metabolism of Acartia clausi was studied experimentally using four different diets: (1) diatom cells of Thalassiosira weissflogii, (2) detritus prepared from the same culture, (3) 50 : 50 mix on a protein basis of the two previous diets, and 4) dinoflagellate cells of Prorocentrum micans. For each trophic, ingestion, gut transit time, trypsin activity and K_m (half saturation constant) were measured at limiting and saturating concentration. Assimilation rates were also estimated for both pure diatoms and mixed live–detrital cell diets. Ingestion followed a Holling type 2 response for diets 1 and 4, a linear one for detritus and an intermediate response for diet 3. Gut transit time displayed different adaptive changes with food regime depending on protein concentration. Trypsin activity was lower for detrital food and trypsin K_m significantly decreased with increasing concentration of live diatoms. Assimilation rates were higher for live food than for mixed live–detrital food. Results illustrated that Acartia-type copepods optimize nitrogen or protein uptake. They suggest that besides chemoreception-mediated selectivity, internal controls by digestion and assimilation also regulate ingestion (feed-back).     

Generation of cyclonic eddies in the Eastern Gotland Basin of the Baltic Sea following dense water inflows: numerical experiments

A sigma (σ)-coordinate ocean model by Blumberg and Mellor (POM) is applied to study the formation processes of mesoscale cyclones observed in the Eastern Gotland Basin following the dense water inflows. The initial conditions simulate a situation when the Arkona and Bornholm basins and partially the Slupsk Furrow are already filled with the inflow water of the North Sea origin, while the Eastern Gotland and Gdansk basins still contain the old water of pre-inflow stratification. Model runs with constant and time-dependent winds, changing the buoyancy forcing, grid geometry and bottom topography display the following. Entering the Eastern Gotland Basin from the Slupsk Furrow, the bottom intrusion of saline inflow water splits in two: one goes northeast towards the Gotland Deep, and second moves southeast towards the Gulf of Gdansk. An intensive mesoscale cyclonic eddy carrying the inflow water is generated just east of the Slupsk Furrow with the inflow pulse. A number of smaller cyclones with boluses of the inflow water are formed in the permanent halocline along the saline intrusion pathway to the Gotland Deep. Following Spall and Price [J. Phys. Oceanogr. 28 (1998) 1598], the cyclones are suggested to form by the adjustment of the high potential vorticity inflow water column to a low potential vorticity environment.     

内置式永磁同步电动机无传感器速度控制和转子初始位置估计方法的应用及实验研究

针对内置式永磁同步电动机传动提出了一种新的无速度传感器控制和转子初始位置估计方法.在内置式永磁同步电动机旋转过程中,采用扩展卡尔曼滤波方法,仅需测量电机定子的电压和电流,便可得到转速和转子位置的估计值.对内置式永磁同步电动机,采用扩展卡尔曼滤波方法的主要困难在于在静止坐标系中其动态模型的复杂性.由于磁路的不对称性,在静止坐标系中建内置式永磁同步电动机的模型比建表面式永磁同步电动机模型更复杂.在无传感器的传动系统中,电机的起动过程是一个问题,因为在起动之前没有任何信息可以获得.转子初始位置估计是在电机静止时,在瞬间对定子绕组施加合适的电压脉冲序列,通过测量峰值电流获得转子位置信息.利用磁饱和效应对凸极性的影响来区分南北磁极.给出基于浮点数字信号处理器TMS320C31平台得到的内置式永磁同步电动机实验结果.     

Stability and competition in intermodal container shipping: finding a balance

This article considers the perennial topic of how to acheive an equilibrium balance between stability and competition in intermodal shipping. It argues that competition is becoming destructive, but that the imbalance is difficult to correct in a climate where competitive pressures are strog everywhere and restraints on competiiton are unfashionable. In this context, pricing of intermodal services, the emergence of multi-trade alliances, the revelance of contestable market theory and developments in regulatory policies are all examimned. Some points towards restoring an equilibrium balance are offered.     

数字图像技术在露石混凝土路面中的应用

应用数字图像技术,将普通数码相机拍摄的露石水泥混凝土路面照片进行处理,根据图像的灰度值变化分析得到露石混凝土路表面的构造深度,并通过与常规方法的比较表明,此方法测量的路表面构造深度结果可靠,操作简单,可以在分析露石混凝土路面粗糙的表面特征上应用。     

基于一次转移原理的限流器研究

研究了基于一次电流转移的限流器方案,它由快速开关和PTC电阻并联组成。限流过程电流由快速开关直接转移至PTC电阻。研究表明,在电流向PTC电阻转移的过程中,电弧电压和PTC电阻值对限流效果有重要影响。     

Comparison of HC species from diesel combustion modes and characterization of a heat-up doc formulation

This study summarizes engine speed and load effects on HC species emissions from premixed charge compression ignition (PCI) and conventional diesel combustion, and it evaluates diesel oxidation catalyst (DOC) formulations on a gas flow reactor for the purpose of diesel particulate filter regeneration or lean NO_x trap desulfation. HC emissions are sampled simultaneously by a Tedlar bag for light HC species and by a Tenax TA™ adsorption trap for semi-volatile HC species, and they are analyzed by gas chromatography with a flame ionization detector. The bulk temperature and residence time during combustion are key parameters that are important for understanding the effects of speed and load on engine-out HC emissions. The degree of post-flame oxidation is higher in PCI than in conventional combustion, and it is increased for PCI with a higher speed and load, as indicated by a lower fuel alkanes/THC ratio, a higher alkenes/fuel alkanes ratio, and a higher methane/THC ratio. Ethene and n-undecane are two representative HC species, and they are used as a surrogate mixture in the gas flow reactor to simulate PCI and conventional combustion with in-cylinder post fuel injection. Among the three DOC formulations tested, the catalyst with constituent precious metals of platinum and palladium (PtPd) showed the best light-off performance, followed by PtPd with an addition of cerium dioxide (PtPd+CeO₂), and platinum (Pt), regardless of exhaust compositions. Conventional combustion exhaust composition shows a lower light-off temperature than that of PCI, regardless of catalyst formulation.     

Thermal design of automobile exhaust based thermoelectric generators: Objectives and challenges

The potential for thermoelectric power generation (via waste heat recovery onboard automobiles) to displace alternators and/or provide additional charging to a vehicle battery pack has increased with recent advances in thermoelectric material processing. In gasoline fueled vehicles (GFVs), about 40% of fuel energy is wasted in exhaust heat, while a smaller amount of energy (30%) is ejected through the engine coolant. Therefore, exhaust-based thermoelectric generators (ETEG) have been a focus for GFV applications since the late 1980s. The conversion efficiency of modern thermoelectric materials has increased more than three-fold in the last two decades; however, disputes as to the thermal design of ETEG systems has kept their overall efficiency at limited and insufficient values. There are many challenges in the thermal design of ETEG systems, such as increasing the efficiency of the heat exchangers (hot box and cold plate), maintaining a sufficient temperature difference across the thermoelectric modules during different operating conditions, and reducing thermal losses through the system as a whole. This paper focuses on a review of the main aspects of thermal design of ETEG systems through various investigations performed over the past twenty years. This paper is organized as follows: first, the construction of a typical ETEG is described. The heat balance and efficiency of ETEG are then discussed. Then, the third section of this paper emphasizes the main objectives and challenges for designing efficient ETEG systems. Finally, a review of ETEG research activities over the last twenty years is presented to focus on methods used by the research community to address such challenges.