Granular effect of fly ash repairs damage of recycled coarse aggregate

Repairing effect of fly ash (FA) on damage of recycled coarse aggregate was evaluated by characteristics of pores and cracks in the vicinity of interracial transition zone (ITZ). The interracial structure between the virgin aggregate and the attached old mortar was investigated and compared with ITZ of recycled aggregate concrete in the presence of FA or ultra-fine FA(UFA) by means of scanning electron microscope (SEM). Diam- eter and plumpness frequency distribution of pores as well as width of the old ITZ, length of contacting points and cracks density were analyzed. The SEM results reveal that the diameter of pores is decreases significantly but pores plumpness increases. A decreased ITZ width and cracks density as well as an increased bonding zone length can also been observed, which indicates that FA or UFA repairs damage of recycled coarse aggregate due to its granular effect.     

Numerical analysis of nonlinear rotor-bearing-seal system

The system state trajectory, Poincard maps, largest Lyapunov exponents, frequency spectra and bifurcation diagrams were used to investigate the non-linear dynamic behaviors of a rotor-bearing-seal coupled system and to analyze the influence of the seal and bearing on the nonlinear characteristics of the rotor sys- tem. Various nonlinear phenomena in the rotor-bearing-seal system, such as periodic motion, double-periodic motion, multi-periodic motion and quasi-periodic motion were investigated. The results may contribute to a further understanding of the non-linear dynamics of the rotor-bearing-seal coupled system.     

Feasibility of localizing in vivo micro-devices with electromagnetic methods

In order to measure the location of medical micro-devices in the gastrointestinal tract, electromagnetic methods were developed considering the magnetic permeability of human bodies. Two varieties of electromagnetic localization methods have been implemented： one uses direct current（DC） to generate the electromagnetic field, and the other uses alternating current （AC）. The two varieties of the localization principle were analyzed and relevant experiments were made. The experiments show that the alternating electromagnetic method acquires higher accuracy, higher stability and wider measurement range.     

Magnetic resonance imaging of atherosclerotic lesion with new devised animal surface coil

The ability of dynamic contrast enhanced magnetic resonance imaging(DCE MRI) with a new devised animal surface coil was analyzed in identifying atherosclerotic plaques in the rabbit medium-sized iliac artery(IA).Then a comparative analysis of multi-detector computed tomography(MDCT) and DCE MRI was done in discerning morphology and components of 80 atherosclerotic plaques identified by histopathology.It shows that the DCE MRI may be an emerging noninvasive and economic way to characterize atherosclerotic plaques at present.What's more, a new devised animal surface coil would further improve the signal-to-noise ratio(SNR) and the quality of imaging.However, CT angiography(CTA) may be better than MR angiography(MRA) in detecting vessel stenosis.     

Hepatic CT image query based on threshold-based classification scheme with gabor features

Hepatic computed tomography(CT) images with Gabor function were analyzed.Then a threshold-based classification scheme was proposed using Gabor features and proceeded with the retrieval of the hepatic CT images.In our experiments, a batch of hepatic CT images containing several types of CT findings was used and compared with the Zhao's image classification scheme, support vector machines(SVM) scheme and threshold-based scheme.     

On the algorithms of adaptive neural network-based speed control of switched reluctance machines

AbstractA switched reluctance machine(SRM)drive is a time-varying,strongly nonlinear system.High performance control can no longer be achieved by using linear techniques.This paper describes the back-propagation (BP)neural network-based proportional-integral-derivative(PID)speed control of the SRM.It’s the interest of this paper to explore the utilization of the prior empirical knowledge as guidance in the initializing and training of the neural networks.The purpose is to make the networks less sensitive on the initial weights.Two modified algorithms are presented and simulation experiments show some interesting findings about their control effects and their corresponding sensitivity on the initial weights of the networks.     

Performance research of a micro-CCHP system with adsorption chiller

This paper describes a new micro-combined cooling,heating and power(CCHP) system,which is especially suitable for domestic and light commercial applications. It mainly consists of a natural gas-fired internal combustion engine,a silica gel-water adsorption chiller and other heat recovery units. In order to study the energy effciency and economic feasibility,an experimental investigation has been carried out. The experimental system has a rated electricity power of 12 kW,a rated cooling capacity of 9 kW and a rated heating capacity of 28 kW. Evaluation and analysis of the system are discussed in detail. The testing results show that the energy effciency of the overall system depends on different modes. The overall thermal and electrical effciency is over 70%. Higher heat load supplied causes higher effciency of the system. Economic evaluation shows that the micro-CCHP system enjoys a small capital cost and short payback period,which is easily accepted by customers. At current natural gas price of 1.9 RMB/m3(nominal condition) and electric price of 0.754 RMB/(kW·h) ,the total capital cost is only 90 000 RMB with a payback period of 3.21 years.     

Effect of absorption layer on interior sound field of sonar dome

Using the finite element method (FEM) and boundary element method (BEM) and considering the sound absorption layer which is covered on the backing of the sonar dome, the interior field in the dome which is excited by the incident plane wave has been studied. This method is validated by comparing numerical results with that of classic elastic theory. Then the effect of parameters of the sound absorption layer on interior sound field has been analyzed. The numerical calculation results show that uniformity of interior sound pressure is improved when the backing is covered with a sound absorption layer. The thicker the layer is, or the higher the loss factor of layer is, the more uniform the sound field is.     

Dynamic recrystallization behavior and microstructural evolution in SPHC steel

The dynamic recrystallization(DRX) behaviors in SPHC steel were investigated with hot compression tests at deformation temperatures of 950-1 150,strain rates of 0.1-15 s-1,and initial austenite grain sizes of 86-232 μm.The effects of deformation temperature,strain,strain rate and the initial austenite grain size on the microstructural evolution during DRX were studied in detail.The results show that DRX is observed under the condition of the Zener-Hollomon parameter being less than 1.07×10 13 s-1.The deformation activation energy for SPHC steel is calculated to be 299.4 kJ/mol by regression analysis.Austenite grain size of DRX is refined with decreasing temperature and increasing strain rate under steady state conditions,but it is not influenced by the initial grain size.The mathematical equation of DRX grain size of SPHC steel is obtained.     

Application of strut-and-tie model for design of interior anchorage zone in post-tensioned concrete structure

This paper presents an application of strut-and-tie model (STM) to design the interior anchorage zone (IAZ) in the post-tensioned concrete structure. The STM theory and range of IAZ are introduced. Then, based on the finite element analysis, a series of simplified equations to calculate internal forces in IAZ are presented. Finally, the STM model for IAZ is given. In the proposed STM model, internal forces in ties vary with the dimension ratio and the eccentricity of load. The U-turn of internal forces is suggested to allocate rebar to resist bearing flexural tensile force. Compared with the FIP (International Federation for Prestressing) model, the proposed STM model is more reasonable and applicable.