A dynamic stochastic assignment model for the analysis of general networks

The paper adopts the framework employed by the existing dynamic assignment models, which analyse specific network forms, and develops a methodology for analysing general networks. Traffic conditions within a link are assumed to be homogeneous, and the time varying O-D travel times and traffic flow patterns are calculated using elementary relationships from traffic flow theory and link volume conservation equations. Each individual is assumed to select a departure time and a route by trading off the travel time and schedule delay associated with each alternative. A route is considered as reasonable if it includes only links which do not take the traveller back to the origin. The set of reasonable routes is not consistant but depends on the time that an individual decides to depart from his origin. Equilibrium distributions are derived from a Markovian model which describes the evolution of travel patterns from day to day. Numerical simulation experiments are conducted to analyse the impact of different work start time flexibilities on the time dependent travel patterns. The similarity between link flows and travel times obtained from static and dynamic stochastic assignment is investigated. It is shown that in congested networks the application of static assignment results in travel times which are lower than the ones predicted by dynamic assignment.     

Prediction of the dimensional deformation of the addendum and dedendum after the warm shrink fitting process using a correction coefficient

The warm shrink fitting process is generally used to assemble automobile transmission parts (shafts/gears). However, this process causes a deformation in the addendum and dedendum of the gear depending on the fitting interference and gear profile, and this deformation causes additional noise and vibration between the gears. To address these problems, the warm shrink fitting process is analyzed by considering the error in the dimensional deformation of the addendum and dedendum found when comparing the results of a theoretical analysis and finite element analysis (FEA). A correction coefficient that reduces this error is derived through an analysis of the difference in the cross-sectional area between the shapes used for the theoretical analysis and that of the actual gear, and a closed-form equation to predict the dimensional deformation of the addendum and dedendum is proposed. The FEA method is proposed to analyze the thermal-structural-thermal coupled field analysis of the warm shrink fitting process (heating-fitting-cooling process). To verify the closed-form equation using the correction coefficient, measurements are made of actual helical gears used in automobile transmissions. The results are in good agreement with those given by the closed-form equation.     

Major sources of hydrocarbon emissions in a premixed charge compression ignition engine

Although premixed charge compression ignition (PCCI) combustion engines are praised for potentially high efficiency and clean exhaust, experimental engines built to date emit more hydrocarbons (HCs) and carbon monoxide (CO) than the conventional machines. These compounds are not only strictly controlled components of the exhaust gas of road vehicles but are also an energy loss indicator. The prime objective of this study was to investigate the major sources of the HCs formed in the combustion chamber of an experimental PCCI engine in order to suggest some effective technologies for HC reduction. In this study, to explore the dominant sources of HC emissions in both operation modes, a single cylinder engine was prepared such that it could operate using either conventional diesel combustion or PCCI combustion. Specifically, the contributions of the top-ring crevice volume in the combustion chamber and the bulk quenching of the lean mixture were investigated. To understand the influence of the shape and magnitude of the crevice on HC emissions, the engine was operated with 12 specially prepared pistons with different top-ring crevices installed one after another. The engine emitted proportionally more HCs as the depth of the crevice increased as long as the width remained narrower than the prevailing quench distance. The top-ring-crevice-originated exhaust HCs comprised approximately 31% of the total HC emissions in the baseline condition. In a series of tests to estimate the effects of bulk quench on exhaust HC emissions, intake air was heated from 300K to 400K in steps of 25K. With the intake air heated, HC and CO emissions decreased with a gradually diminishing rate to zero at 375K. In conclusion, the most dominant sources of HC emissions in PCCI engines were the crevice volumes in the combustion chamber and the bulk quenching of the lean mixtures. The key methods for reducing HC emissions in PCCI engines are minimizing crevice volume in the combustion chamber and maximizing intake air temperature allowed based on the permissible NOx level.     

Comparative analysis of vehicle brake data in the ministry of transport test on the roller brake tester and on flat ground

This study performs a comparison between what occurs when braking on a Ministry of Transport (MOT) brake tester and on flat ground. The tire pressure is changed, but the other parameters remain constant. The results from this research and from the in-depth comparative study conducted by the mechanical engineering staff in the mechanical laboratory at the Miguel Hernández University in Elche have led to the following main conclusions: By varying the tire pressure, false results can be obtained with the MOT brake tester, which means that, if the tires are inflated at a low pressure but the brakes are in good condition, the vehicle will not pass the MOT. Conversely, if the brakes are in poor condition but the tire pressure is higher than what is recommended by the manufacturer, a false pass is produced. This article shows that the MOT brake testing equipment is often wrong and inexact, and the data and graphs presented prove that the tire pressure is a determining factor when assessing the condition of brakes.     

Topology optimization of gas flow channel routes in an automotive fuel cell

An efficient topology optimization method for fluid-structure problems was developed in an effort to determine the optimum flow channel route in a fuel cell bipolar plate from first principles. This study describes the derivation and solution of new mathematical equations for topology optimization combining a density-based algorithm, the interpolation method of moving asymptotes (MMA), and the incompressible Navier-Stokes equation with a term representing the chemical reaction between hydrogen and the catalyst. The present method is based on the finite element method with a newly developed reaction rate equation. In this model, a topology variable of 0 represents viscous flow, whereas a value of 1 indicates porous flow. The flow velocity and pressure were obtained from the Navier-Stokes equation and constraints and element matrices for sensitivity analyses during the optimization. MMA was utilized to calculate the optimum flow routes in the design domain. The influence of the key design parameter q and the pressure drop on the optimum topology were also investigated. The channel topology became smoother with decreasing q, and the number of channels increased with increasing pressure drop.     

High-strain-rate fracture of adhesively bonded composite joints in DCB and TDCB specimens

Double-cantilever beam (DCB) and tapered double-cantilever beam (TDCB) specimens are the test configurations most commonly used to measure the fracture toughness of composites and adhesive joints. Strain rates of 1 to 18.47 m/s were applied to the test specimens via high-speed hydraulic test equipment. Because the fracture occurs through the adhesively bonded joints and the cracks grow rapidly, the crack length and beam displacement were recorded by a high-speed camera. An energy range from 0 to 10 J was often observed in the high-strain-rate fracture experiments for nonlinear plastic behavior of the dynamically loaded adhesively bonded DCB and TDCB specimens. The range of energy release rates (fracture energy) for TDCB specimen was 2 to 3 times higher than that of a DCB specimen for all high strain rates. The fracture energy of automotive adhesive joints can be estimated using the experimental results in this study for the fracture toughness (G_IC) under high rates of loading. The crack grows as the applied fracture energy exceeds the value of the critical energy release rate (G_IC) at the crack tip. The energy release rate was calculated using the fracture mechanics formula. The key fracture mechanics parameter, the fracture energy GIC, was ascertained as a function of the test rate and can be used to assess and model the overall joint performance.     

Fuel consumption of fuel cell hybrid vehicles considering battery SOC differences

Fuel cell hybrid vehicles (FCHVs) have become one of the most promising candidates for future transportation due to current energy supply problem and environmental problem. Fuel economy is an important factor in FCHVs. In order to properly evaluate the fuel economy of an FCHV, the initial battery state of charge (SOC) and the final battery SOC have to be identical so that the effect of the battery energy usage on the fuel economy is neglected. In the simulation or in the real driving, however, the final battery SOC is usually different from the initial battery SOC, and the final battery SOC often depends on the power management strategy. To consider the difference between the two battery SOC values, the concept of equivalent fuel consumption is presented by two methods. One is based on the relationship between delta SOC and delta fuel consumption, and the other is based on the optimal control theory. Two rule-based power management strategies for an FCHV are presented, and for each strategy, the fuel economy is evaluated based on the two methods. The characteristics of the two methods are discussed and compared, and the superior one is selected based on the comparison.     

Policy challenges of increasing automation in driving

The convergence of information and communication technologies (ICT) with automotive technologies has already resulted in automation features in road vehicles and this trend is expected to continue in the future owing to consumer demand, dropping costs of components, and improved reliability. While the automation features that have taken place so far are mainly in the form of information and driver warning technologies (classified as level I pre-2010), future developments in the medium term (level II 2010–2025) are expected to exhibit connected cognitive vehicle features and encompass increasing degree of automation in the form of advanced driver assistance systems. Although autonomous vehicles have been developed for research purposes and are being tested in controlled driving missions, the autonomous driving case is only a long term (level III 2025 +) scenario. This paper contributes knowledge on technological forecasts regarding automation, policy challenges for each level of technology development and application context, and the essential instrument of cost-effectiveness for policy analysis which enables policy decisions on the automation systems to be assessed in a consistent and balanced manner. The cost of a system per vehicle is viewed against its effectiveness in meeting policy objectives of improving safety, efficiency, mobility, convenience and reducing environmental effects. Example applications are provided that illustrate the contribution of the methodology in providing information for supporting policy decisions. Given the uncertainties in system costs as well as effectiveness, the tool for assessing policies for future generation features probabilistic and utility-theoretic analysis capability. The policy issues defined and the assessment framework enable the resolution of policy challenges while allowing worthy innovative automation in driving to enhance future road transportation.     

Fuzzy-logic applied to yaw moment control for vehicle stability

In this paper, we propose a new yaw moment control based on fuzzy logic to improve vehicle handling and stability. The advantages of fuzzy methods are their simplicity and their good performance in controlling non-linear systems. The developed controller generates the suitable yaw moment which is obtained from the difference of the brake forces between the front wheels so that the vehicle follows the target values of the yaw rate and the sideslip angle. The simulation results show the effectiveness of the proposed control method when the vehicle is subjected to different cornering steering manoeuvres such as change line and J-turn under different driving conditions (dry road and snow-covered).     

基于车激动力响应互相关指标的桥梁基础冲刷诊断方法

针对当前桥梁基础冲刷诊断和检测方法过程复杂、成本高且受环境影响大等问题,提出一种基于车激动力响应互相关指标的桥梁基础冲刷诊断方法。该方法通过桥墩和桥跨不同测点的纵向加速度响应自由衰减段信号的互相关分析,建立基础冲刷诊断指标体系,实现冲刷定位和均匀性诊断。首先,依据互相关函数幅值向量置信度判据指标进行基础冲刷初判;然后,通过响应互相关函数幅值向量因子变化率向量进行冲刷定位,再根据横桥向互相关函数幅值变化率向量诊断冲刷均匀性;并通过统计评估方法提高诊断精度;最后,结合1座连续梁桥算例进行多种冲刷工况的数值仿真分析,对所提方法的有效性和适用性进行验证。结果表明：该方法能够很好地实现基础冲刷的定位和均匀性诊断,指标具有较高敏感性;同时具有较好的抗噪性能,通过所提出诊断指标体系的综合使用可消除噪声对诊断结果的干扰。该方法具有诊断结果精度高、过程简便易行、无需进行复杂且误差较大的模态识别、允许试验测试参数和条件适量变化等优点,可嵌入常规桥梁荷载试验同步开展,具有很好的工程应用潜力和实用价值。