天津港深水化及二港岛建设水沙环境研究

根据天津市城市总体规划和产业布局,结合天津港30万吨级航道及东疆第二港岛的建设,基于多年实测水文泥沙等资料,采用现场观测、演变分析、物理模型和数学模型等多种手段,对港口深水化及港岛工程实施后的水流泥沙运动特征及产生的环境效应问题进行了综合性试验研究,其成果为工程的建设提供了科学依据。     

Precise and reliable positioning based on the integration of navigation satellite system and vision system

In this paper, we propose a precise and reliable positioning method for solving common problems, such as a navigation satellite’s signal occlusion in an urban canyon and the positioning error due to a limited number of visible navigation satellites. This is an integrated system of the navigation satellites system and a vision system. In general, the navigation satellite positioning system has a fatal weakness in that it can not calculate a position coordinate when its signal is occluded by some obstacle. For this reason, positioning by using the navigation satellites system can not be used for a variety of applications. Therefore, we propose as a method to integrate both the navigation satellites system and the vision system. Some target objects that have accurate position coordinates, for example, in an outdoor shaded area like an urban canyon, are installed into the vision system. When the vision system recognizes a target object it loads the accurate coordinate of that target object. Then, it measures the distance by using the disparity from the camera sensor to the target object. These distance and object coordinate data are used for positioning with the navigation satellites system’s data. This integrated system can be used for the positioning solution where the user is in unfavorable conditions. This paper shows that the algorithm of integrated system and the numerical test performed. The results indicate that the reliable and stable positioning can be obtained by introducing the vision system to the satellite navigation system.     

Development of a model of the dual clutch transmission in autonomie and validation with dynamometer test data

Owing to ever more stringent regulations and customers’ expectations, auto manufacturers have been considering numerous technology options to improve vehicle fuel economy. One of these is transmission technology, which has been shown to be one of the most cost-effective technologies. Over the past few years, transmissions have significantly evolved and have impacted both performance and fuel efficiency. As one of the advanced tranmissions, the dual clutch transmission (DCT) is the first automatic transmission to provide better efficiency than manual transmissions. DCTs provide reduced shift shocks and better driver comfort in addition to higher top speeds and torques. In this paper, a model and shifting controller for the DCT are developed in the vehicle systems context using Autonomie, a model-based vehicle simulation tool. Finally, the Autonomie DCT model and control strategy are validated using vehicle test data from Argonne’s Advanced Powertrain Research Facility.     

Micro deformation of automobile hood in dipping process using stiffness

Technicians have been going through trial-and-error processes to solve very small or micro deformation on automobile hood during the painting process. In order to establish a systematic improvement procedure which can replace the time-consuming trial-and-error method to reduce defects, an accurate analysis of how micro deformation occurs during the painting process is needed. We have utilized a stiffness scanning method in automobile hood and reverse engineering to build up a reliable and accurate structural analysis and measurement procedures. We measured the load-stroke data at critical locations on automobile hood through stiffness scanning to determine material constants closest to the measurement by assuming several critical hood parts, such as sealer inside the hood, hemming part, spot weld part, and other uncertain joints, as virtual elastic materials. After setting the difference between analytical and measured load-stroke data as an objective function, we computed and minimized it by using the response surface method and partial differentiation of the object function. As a result, by obtaining the reliability was over 91%, which showed a strong correlation between analysis and measured results. By comparing the actual strain measured in real painting lines with calculated strain, we confirmed the validity of our structural analysis method. It was concluded that the proper analysis tool could be utilized in determination of optimal locations of supports during the painting process.     

Public responses to policies designed to internalise environmental and social externalities from road transport in New Zealand

Based on a public survey of registered voters, we explore four options for internalising the social and environmental costs of road transport. The options were presented together with generalised factual information about their benefits and costs. Respondents are highly supportive of fuel use efficiency standards and exhaust gas quality standards, with lesser support for proposed initiatives of road user charges and speed reduction. Demographic analysis of responses enables identification of those who might favour or oppose particular options. In this case women are identified as being strongly supportive of the speed reduction option.     

A comparative study of a hybrid Logit–Fratar and neural network models for trip distribution: case of the city of Isfahan

This paper introduces a new procedure to forecast the future O/D demand. It is a hybrid of logit and Fratar model. The hybrid model has the long run, policy sensitive, characteristic of a logit model, calibrated at sector‐level with little/no zero O/D cells. This feature, joint with a Fratar‐type operation at zonal level within a sector, gives a better performance to this model than either of the two types of the models alone. The performance of the hybrid model is contrasted with a neural network model, and shows encouraging results in a real case. Copyright © 2010 John Wiley & Sons, Ltd.     

小型渔政船线型及附体设计优化

选取某近海小型渔政船典型船型,研究艏艉线型和附体对船舶阻力性能的影响。通过对线型、船型系数以及舭龙骨、压浪板、呆木等常规附体对小型渔政船航行性能的影响进行数值模拟分析,优化船舶线型,针对小型渔政船的功能需求选取合适的附体组合形式,并通过实船运行验证优化后的渔政船航行性能有所改善,达到预期目标,可为同型船舶设计提供参考依据。