Urea-SCR system optimization with various combinations of mixer types and decomposition pipe lengths

The demand for NO_x after-treatment system has increased dramatically due to the stricter NO_x emission regulations for diesel vehicles. The urea-SCR system is one of the NO_x after-treatment methods found to be quite effective to meet the regulation requirement enforced by various authorities including the Euro-6. In order to develop an effective urea-SCR system, it is critical to establish an even distribution of reductant over the catalyst surface since this favorable distribution can increase reduction reaction and in turn, improve NO_x conversion efficiencies. In the current study, a number of design variations of the urea-SCR system which included two mixer types and three decomposition pipe lengths, were evaluated systematically using CFD analysis and experimental measurements. The purpose of the CFD analysis was to estimate the distribution of reductant within the urea-SCR system with a specific configuration and the purpose of the engine emission test was to measure the amount of NO_x reduction, respectively. The results from the systematic analysis revealed the relation between the reductant distribution over the SCR and the performance of the NO_x reduction.     

Multiphysic modelling of railway vehicles equipped with pneumatic suspensions

This article presents a multidisciplinary approach of railway pneumatic suspension modelling: both multibody and pneumatic aspects are taken into account. The work aims at obtaining a realistic model of the secondary suspension and coupling it with a multibody model of a train. Various components of the pneumatic circuit such as bellows, tanks, pipes and valves are taken into account. The article focuses on the bellow-pipe-tank subsystem for which several modelling approaches are presented and compared. Differences between differential and algebraic models are highlighted, and an application-dependent choice between them is suggested. A complete model of the pneumatic circuit is then obtained and coupled with a multibody model of the train. As a result, the behaviour of a suburban train equipped with a pneumatic secondary suspension is analysed, in particular undesired oscillating motions which affect the comfort. Topological modifications and improvements of the suspension are also investigated and discussed.     

Analysis of the capabilities of a two-stage turbocharging system to fulfil the US2007 anti-pollution directive for heavy duty diesel engines

This article presents a two-stage turbocharged heavy-duty diesel (HDD) engine designed to fulfil the US2007 anti-pollution directive. This directive imposes very restrictive limits on the NOx and particle emissions of HDD engines. In this work, the possibility of combining particle traps in the exhaust line to reduce soot emissions with very high EGR rates to reduce NOx emissions is considered. This new generation engine implements two-stage turbocharging in order to improve the bsfc when the engine is working on steady conditions as well as to optimize the engine transient response. After carrying out the tests, the results were analyzed and the engine settings were adjusted to maximise its behaviour and minimise pollutant emissions. NOx and soot emission peaks were also analyzed at engine transient conditions in order to keep them under certain levels, and thus maintain the overall pollutant emissions to a level that is as low as possible. In summary, a double-stage turbocharging configuration can greatly improve engine driveability (between 23% and 36% depending on engine speed), while reducing NOx emissions during transient evolution without increasing opacity peaks beyond the stated limits.     

Thermal design of automobile exhaust based thermoelectric generators: Objectives and challenges

The potential for thermoelectric power generation (via waste heat recovery onboard automobiles) to displace alternators and/or provide additional charging to a vehicle battery pack has increased with recent advances in thermoelectric material processing. In gasoline fueled vehicles (GFVs), about 40% of fuel energy is wasted in exhaust heat, while a smaller amount of energy (30%) is ejected through the engine coolant. Therefore, exhaust-based thermoelectric generators (ETEG) have been a focus for GFV applications since the late 1980s. The conversion efficiency of modern thermoelectric materials has increased more than three-fold in the last two decades; however, disputes as to the thermal design of ETEG systems has kept their overall efficiency at limited and insufficient values. There are many challenges in the thermal design of ETEG systems, such as increasing the efficiency of the heat exchangers (hot box and cold plate), maintaining a sufficient temperature difference across the thermoelectric modules during different operating conditions, and reducing thermal losses through the system as a whole. This paper focuses on a review of the main aspects of thermal design of ETEG systems through various investigations performed over the past twenty years. This paper is organized as follows: first, the construction of a typical ETEG is described. The heat balance and efficiency of ETEG are then discussed. Then, the third section of this paper emphasizes the main objectives and challenges for designing efficient ETEG systems. Finally, a review of ETEG research activities over the last twenty years is presented to focus on methods used by the research community to address such challenges.     

Simulation of city bus performance based on actual urban driving cycle in China

This paper establishes the simulation model of a city bus on the basis of the EQ6110 bus prototype and its experimental data. According to the actual urban driving cycle, the fuel economy and the traction performance of the EQ6110 city bus have been simulated, and factors such as the driving cycle, the loss of power to engine accessories, the gear-shifting strategy, the fuel shut-off strategy of the engine, etc., which influence on the bus’s fuel economy, are also quantitatively analyzed. Some conclusions are drawn as follows: (1) driving cycles have a great influence on the fuel economy of a city bus; (2) under the typical urban driving cycle of the public bus in China, the engine fuel shut-off strategy can save about 1 to 1.5 percent of the fuel consumption; and (3) the optimized gear-shifting rules can save 6.7 percent of the fuel consumption. Experimental results verify that the fuel economy for the EQ6110 public bus is improved by 7.2 pecent over the actual Wuhan urban driving cycle of the current public bus in China.     

Comparison of HC species from diesel combustion modes and characterization of a heat-up doc formulation

This study summarizes engine speed and load effects on HC species emissions from premixed charge compression ignition (PCI) and conventional diesel combustion, and it evaluates diesel oxidation catalyst (DOC) formulations on a gas flow reactor for the purpose of diesel particulate filter regeneration or lean NO_x trap desulfation. HC emissions are sampled simultaneously by a Tedlar bag for light HC species and by a Tenax TA™ adsorption trap for semi-volatile HC species, and they are analyzed by gas chromatography with a flame ionization detector. The bulk temperature and residence time during combustion are key parameters that are important for understanding the effects of speed and load on engine-out HC emissions. The degree of post-flame oxidation is higher in PCI than in conventional combustion, and it is increased for PCI with a higher speed and load, as indicated by a lower fuel alkanes/THC ratio, a higher alkenes/fuel alkanes ratio, and a higher methane/THC ratio. Ethene and n-undecane are two representative HC species, and they are used as a surrogate mixture in the gas flow reactor to simulate PCI and conventional combustion with in-cylinder post fuel injection. Among the three DOC formulations tested, the catalyst with constituent precious metals of platinum and palladium (PtPd) showed the best light-off performance, followed by PtPd with an addition of cerium dioxide (PtPd+CeO₂), and platinum (Pt), regardless of exhaust compositions. Conventional combustion exhaust composition shows a lower light-off temperature than that of PCI, regardless of catalyst formulation.     

A self-powering system based on tire deformation during driving

Tire intelligence is vital in the improvement of the safety of vehicles because the tire supports the car body and is the contact point between the vehicle and the road. To create an intelligent tire, sensors must be installed to measure the behavior of the tire. However, it is difficult to apply a wired sensor system on the wheel of the tire. Hence, it is necessary to implement a self-powering, wireless system (a type of energy harvesting system) that can be mounted inside the tire. The purpose of this study is to convert the strain energy caused by deformation of the tire while driving into useful electrical energy to supply the sensor system. A flexible piezofiber is utilized for the energy conversion. The variation in strain, due to changes in speed, load, and the internal pressure of the tire, was measured along two axial directions to evaluate the amount of available strain energy. The amount of strain changed from 0.15% to 0.8%. To predict the amount of available energy from a tire, we perform an analysis of the relationship between the strain and the voltage. In addition, experiments for impedance matching between piezofiber and related circuits were conducted to optimize the external loads for transferring energy efficiently. Based on the procedure mentioned above, at least 0.58 mJ of electrical energy can be generated by using the laterally oriented strain (1500 to 2500 micro strain). The result of this study is expected to enhance the potential realization of self-generating wireless sensor systems for so-called ??intelligent?? tires.     

Study of an optimized gas strut layout to improve opening and closing quality

The most important factor in gas strut design is determining an optimized layout. If the layout is not optimized, vehicle operators will have a suboptimal experience when opening and closing the tailgate. A poor layout of the gas struts causes operators to work excessively when they open/close the tailgate, and vehicle owners will incur additional expenses due to deterioration in the body quality of the vehicle. Thus, an optimized gas strut layout is very important, even if it does not seem interesting. This paper describes the tailgate operation process and focuses on determining an optimized gas strut layout for opening/closing the tailgate easily.     

High-strain-rate fracture of adhesively bonded composite joints in DCB and TDCB specimens

Double-cantilever beam (DCB) and tapered double-cantilever beam (TDCB) specimens are the test configurations most commonly used to measure the fracture toughness of composites and adhesive joints. Strain rates of 1 to 18.47 m/s were applied to the test specimens via high-speed hydraulic test equipment. Because the fracture occurs through the adhesively bonded joints and the cracks grow rapidly, the crack length and beam displacement were recorded by a high-speed camera. An energy range from 0 to 10 J was often observed in the high-strain-rate fracture experiments for nonlinear plastic behavior of the dynamically loaded adhesively bonded DCB and TDCB specimens. The range of energy release rates (fracture energy) for TDCB specimen was 2 to 3 times higher than that of a DCB specimen for all high strain rates. The fracture energy of automotive adhesive joints can be estimated using the experimental results in this study for the fracture toughness (G_IC) under high rates of loading. The crack grows as the applied fracture energy exceeds the value of the critical energy release rate (G_IC) at the crack tip. The energy release rate was calculated using the fracture mechanics formula. The key fracture mechanics parameter, the fracture energy GIC, was ascertained as a function of the test rate and can be used to assess and model the overall joint performance.     

The impact of weather conditions on bikeshare trips in Washington,DC

Bicycle usage can be affected by colder weather, precipitation, and excessive heat. The research presented here analyzes the effect of weather on the use of the Washington, DC, bikeshare system, exploiting a dataset of all trips made on the system. Hourly weather data, including temperature, rainfall, snow, wind, fog, and humidity levels are linked to hourly usage data. Statistical models linking both number of users and duration of use are estimated. Further, we evaluate trips from bikeshare stations within one quarter mile of Metro (subway) stations at times when Metro is operating. This allows us to determine whether Metro serves as a back-up option when weather conditions are unfavorable for bicycling. Results show that cold temperatures, rain, and high humidity levels reduce both the likelihood of using bikeshare and the duration of trips. Trips taken from bikeshare stations proximate to Metro stations are affected more by rain than trips not proximate to Metro stations and less likely when it is dark. This information is useful for understanding bicycling behavior and also for those planning bikeshare systems in other cities.