Quality evaluation of car window motors using sound quality metrics

In this paper, a method to establish a decision criterion to evaluate the quality of small window motors using sound quality (SQ) metrics is suggested. Although the sound level radiated from the motor is relatively small compared to other sounds in a car, the sound from an abnormal motor gives an uncomfortable feeling and the impression of abnormal operation, which can lead to customer complaints. To construct an objective decision criterion, the correlation between the SQ metrics and the subjective decision on the passing or failure of the motor were investigated. Four representative SQ metrics, viz., loudness, sharpness, roughness, and fluctuation strength, were calculated for the collected samples. It was observed that the loudness and roughness of the motor sample group classified as abnormal was higher than those of the normal motors. For a single figure rating for motor quality, an evaluation index for the motor sound was generated by combining the correlated SQ metrics with proper weightings. Evaluation results on the specimens that were not employed in generating the quality evaluation index showed a reasonable agreement with the subjective test at 73%. The suggested quality check method can replace the current subjective decision procedure to identify the faulty motors.     

Damper modeling for dynamic simulation of a large bus with MR damper

In this study, a large bus is tested to measure its dynamic response by the single-lane change test and the rapid stop test. A full car model is established by ADAMS/Car for computer simulation. For multibody modeling of a large bus, user-defined templates are used in the simulation. Simulation results of the single-lane change test and the rapid braking test are compared to the results of the physical experiments, in which several sensors are installed to measure the vehicle’s responses. The results obtained from the simulation show good agreement with the tests’ results. A dynamic model for the MR(magnetic-rheological) damper is also developed by employing the Magic Formula model, which is widely used in the nonlinear modeling of a tire. Bump simulation of a full car with the MR damper is carried out to verify the performance of the MR damper. The comparison of the simulation results obtained with the MR damper model to the results obtained with the traditional passive damper model showed improved response of the vehicle with the MR damper.     

Effect of fuel stratification on initial flame development: Part 3-high swirl condition

This paper discusses the final investigation into the effect of fuel stratification on flame propagation. In previous works, the characteristics under the no port-generated swirl condition and the low-swirl condition were considered. For this purpose, the initial flame development and propagation were visualized under different axially stratified states in a modified optical single-cylinder SI engine. The images were captured by an intensified CCD camera through the quartz window mounted in the piston. Stratification was controlled by the combination of the port swirl ratio and injection timing. These were averaged and processed to characterize the flame propagation. The flame stability was estimated by the weighted average of flame area and luminosity. The stability was also evaluated through the standard deviation of flame area and propagation distance and through the mean absolute deviation of the propagation direction. The results show that the LML is expanded remarkably under the high-swirl cases up to the highest relative AFRs of 1.71 and 1.75 between 140 and 160CA. In addition, similar to the low-swirl condition, the flame-flow interaction determines the direction of flame propagation, and the governing roles of the two factors vary according to the swirl level; the flow is more important at the higher swirl conditions, and the flame is more important at the lower swirl condition. Finally, fast and stable flame propagation can be achieved under the preferably stratified condition, which is induced by the suitable combination of the high swirl and injection timing.     

双通线加热的热力学及实验分析(英文)

The present investigation deals with process analysis of oxy-acetylene flame assisted double pass line heating for varying plate thickness. oxy-acetylene flame as the heat source for multi pass line heating to achieve 3-D bending of plates with varying thicknesses was studied. The oxy-acetylene flame was modeled as the moving heat source in the FEM analysis. The transient thermal histories were predicted taking into account the temperature dependent thermo-mechanical properties. A comparative study between single pass and double pass line heating residual deformation was also carried out. The temperature distribution and residual deformations predicted by the numerical model developed in the present work compared fairly well with those of the experimental ones.     

Simulating the impacts of household travel on greenhouse gas emissions,urban air quality,and population exposure

This paper establishes a link between an activity-based model for the Greater Toronto Area (GTA), dynamic traffic assignment, emission modelling, and air quality simulation. This provides agent-based output that allows vehicle emissions to be tracked back to individuals and households who are producing them. In addition, roadway emissions are dispersed and the resulting ambient air concentrations are linked with individual time-activity patterns in order to assess population exposure to air pollution. This framework is applied to evaluate the effects of a range of policy interventions and 2031 scenarios on the generation of vehicle emissions and greenhouse gases in the GTA. Results show that the predicted increase of approximately 2.6 million people and 1.3 million jobs in the region by 2031 compared to 2001 levels poses a major challenge in achieving meaningful reductions in GHGs and air pollution.     

Discretionary activity location choice: in-home or out-of-home?

This paper examines the location choice associated with discretionary activities (in-home vs. out-of-home). These substitution patterns are important in terms of travel demand as in-home activities do not necessitate travel while out-of-home activities incur travel. Mixed logit models are estimated using an activity dataset (2003 CHASE data) to analyze the factors associated with this choice at the individual activity-level. Results suggest that the attributes of an activity significantly contribute to understanding the likelihood of engaging in out-of-home activities. Activity type interaction terms reveal the varying influence that socio-demographics, activity attributes and travel have over four different activity types modeled. The results reveal that the location choice (in-home vs. out-of-home) is sensitive to travel characteristics. As the travel time and cost increases, an individual is less likely to engage in an activity out-of-home. Compared to passive and social activities, the location of active activities is more sensitive to changes in travel attributes.     

Modeling multi-unit vehicle dynamics for low-speed path-following assessment off-highway

This paper proposes a non-linear dynamics model for articulated vehicles. This model is able to capture common low-speed behaviours of any articulated vehicles off-highway, such as operating for a corner or roundabout on a cambered or slippery surface. It can be used to assess the low-speed manoeuvrability of articulated vehicles under such manoeuvres and conditions. The vehicle model was validated by comparing its path tracking performance to that of the field tests.     

Dynamics of LRT growth: Karlsruhe since 1975

The public transport system of Karlsruhe, in particular its innovative services on jointly used heavy rail lines, has received substantial attention throughout the past 20 years. The discussion of the system and of its development has been rather limited in the past, mostly highlighting technical aspects. This paper provides an overview of the development, including the urban development, of the region and of the funding system. The ridership and financial development of the operator is documented in detail. Three case studies focus on the integration of the system development in the general political process of the region and demonstrate the limitations of the operator under its current ownership structures.     

Remoteness and accessibility in the vulnerability analysis of regional road networks

This paper considers the development of a method for network vulnerability analysis which considers the socio-economic impacts of network degradation and seeks to determine the most critical locations in the network. The method compares the levels of remoteness (or its inverse, accessibility) of localities within the study region, on the basis of the impacts of degradation of the road network on a recognised accessibility/remoteness index that can be applied to each and every location within the region. It thus extends the earlier work on accessibility-based vulnerability analysis which was limited to assessment of impacts on selected nodes in a network. The new method allows study of impacts on both specified locations (which do not have to be represented as network nodes) and the region as a whole. The accessibility/remoteness index is defined so that an accessibility surface can be calculated for the region, and the volume under this surface provides an overall measure of accessibility. Changes in the volume under different network states thus reflect the overall impacts. The method is applied to a rural region in south east Australia.     

Exhaust emissions and its control methods in compression ignition engines: A review

Extensive usage of automobiles has certain disadvantages and one of them is its negative effect on environment. Carbon dioxide (CO₂), carbon monoxide (CO), hydrocarbons (HC), oxides of nitrogen (NO_x), sulphur dioxide (SO₂) and particulate matter (PM) come out as harmful products during incomplete combustion from internal combustion (IC) engines. As these substances affect human health, regulatory bodies impose increasingly stringent restrictions on the level of emissions coming out from IC engines. This trend suggests the urgent need for the investigation of all aspects relevant to emissions. It is required to modify existing engine technologies and to develop a better after-treatment system to achieve the upcoming emission norms. Diesel engines are generally preferred over gasoline engines due to their undisputed benefit of fuel economy and higher torque output. However, diesel engines produce higher emissions, particularly NO_x and PM. Aftertreatment systems are costly and occupy more space, hence, in-cylinder solutions are preferred in reducing emissions. Exhaust gas recirculation (EGR) technology has been utilized previously to reduce NO_x. Though it is quite successful for small engines, problem persists with large bore engines and with high rate of EGR. EGR helps in reducing NO_x, but increases particulate emissions and fuel consumption. Many in-cylinder solutions such as lower compression ratios, modified injection characteristics, improved air intake system etc. are required along with EGR to accomplish the future emission norms. Modern combustion techniques such as low temperature combustion (LTC), homogeneous charge compression ignition (HCCI), premixed charge compression ignition (PCCI) etc. would be helpful for reducing the exhaust emissions and improving the engine performance. However, controlling of autoignition timing and achieving wider operating range are the major challenges with these techniques. A comprehensive review of diesel engine performance and emission characteristics is given in this paper.