Effects of information in road transport networks with recurrent congestion

This paper aims to gain more insight into the implications of information provision to drivers on the performance of road transport networks with recurrent congestion. For this purpose, a simulation program consisting of three components has been written. The first component is the traffic simulation model, the second component is the information provision mechanism, and the third component monitors the behavioural decision-making process of the drivers, which is modelled using a utility-based satisficing principle. Three types of information provision mechanisms will be considered: information based upon own-experience, after-trip information and real-time en route information. The findings in this paper, obtained in a hypothetical context, underline the important relationship betweenoverreaction, thelevel of market penetration and thequality of the information. High quality information allows a high level of market penetration, while low quality information, even when provided at low levels of market penetration, induces overreaction. Furthermore, real-time en route information is in particular beneficial during the process leading to a steady state; it reduces the variance in travel time considerably. The paper concludes with a discussion on the market potential of motorist information systems when commercially marketed.     

A review of the Effect of α/W ratio on fracture toughness （Ⅱ） experimental investigation in LEFM

In part I of this series, experimental investigation in EPFM （elastic-plastic fracture mechanics） had been discussed. In this paper, experimental investigation in LEFM （ linear elastic fracture mechanics） is given. Fracture toughness tests had been carried out on three different strength steels, using both through-cracked specimens with different α/W ratio and semi-elliptical cracked specimens with variable crack size and shape. Results show that the fracture toughness KIC increases with decreasing α/W when α/W 〈 0.3 for three-point-bend specimens, and that for α/W 〉 0.3, it is independent of α/W. Shallow crack specimens, both through-cracked and surface-cracked, gave markedly higher values than deeply notched specimens. However, the effect of crack shape on fracture toughness is negligible. Results also show that the LEFM approach to fracture is not tenable for design stresses where αc is often very small, far less than 2.5 （ KIC/σy）^2.     

Environmental trends of ports and harbours: Implications for planning and management

The traditional view of ports as evolving from human settlements to distribution centres is re-examined in an ecological context. The discussion is essential because of the persisting traditional approach to 'global' port development, i.e. directed primarily by technological optimization related to cargo transfer and ocean trasportation. Growing environmental concerns and realities indicate the need for a broader environmental view in which the port is recognized as part of a larger interactive coastal ecosystem, with environmental pressures by the port on the surrounding environment, as well as by the environment on the port. The paper argues for an ecological basis for coastal port development, analyses the environment implications of riverine linkages between port and hinterland, and details some environmental consequnces of changing industrialization and chemical practices. It also identifies initiatives for relevant planning and future port management.     

Micro-Grinding Performance of Hard-Brittle Chip Materials in Precision Micro-Grinding Microgroove

The micro-structure on hard-brittle chip materials (HBCMs) surface can produce predominant functions and features. The micro-grinding with diamond wheel micro-tip is an efficient method to machine microstructure on HBCMs. However, different HBCMs and crystal orientation may have a significant influence on the micro-grinding performance. In this paper, the micro-grinding performance along different crystal orientation of HBCMs is investigated. First, a dressed 600^# diamond grinding wheel is used to micro-grind micro-structure on HBCMs. Then, the experiment of micro-grinding force test is completed. Finally, the quality of microgroove, the grinding ratio and the micro-grinding force are investigated and they are related to the crystal orientation of HBCMs. It is shown that the stronger resistance to the micro-crack propagation has the best quality of microgroove and the smallest grinding ratio. Moreover, the hardest single-crystal SiC has the best machinability and the micro-grinding force is 38.9%, 10.8% and 46.8% less than the one of sapphire, single-crystal Si and quartz glass, respectively. The direction to micro-grind easily is the crystal orientation 〈10\(\overline 1 \)0〉 for single-crystal SiC and sapphire. In addition, the micro-grinding force increases with the increase of the micro-grinding depth and feed rate and decreases with the increase of the grinding wheel speed.     

Lattice-based group signature with verifier-local revocation

Among several post quantum primitives proposed in the past few decades, lattice-based cryptography is considered as the most promising one, due to its underlying rich combinatorial structure, and the worst-case to average-case reductions. The first lattice-based group signature scheme with verifier-local revocation(VLR) is treated as the first quantum-resistant scheme supported member revocation, and was put forward by Langlois et al. This VLR group signature(VLR-GS) has group public key size of O(nm log N log q), and a signature size of O(tm log N log q log β). Nguyen et al. constructed a simple efficient group signature from lattice, with significant advantages in bit-size of both the group public key and the signature. Based on their work, we present a VLR-GS scheme with group public key size of O(nm log q) and signature size of O(tm log q). Our group signature has notable advantages: support of membership revocation, and short in both the public key size and the signature size.     

Correlation between automotive CO, HC, NO, and PM emission factors from on-road remote sensing: implications for inspection and maintenance programs

Carbon monoxide (CO), hydrocarbon (HC), and nitrogen oxide (NO) emission factors (EFs) are measured with a commercial vehicle emissions remote sensing system (VERSS) during a large-scale vehicle exhaust emissions study in Las Vegas. Particulate matter (PM) EFs are simultaneously measured for individual vehicles with a newly developed PM-VERSS based on ultraviolet backscatter light detection and ranging (Lidar). The effectiveness of CO and HC EFs as proxy for NO and PM EFs for spark-ignition vehicles is evaluated. Poor correlations were found between EFs for pollutants on an individual vehicle basis indicating that high EFs for one or more pollutants cannot be used as a predictor of high EFs for other pollutants. Stronger functional relationships became evident after averaging the EF data in bins based on rank-order of a single pollutant EF. Low overlap between the highest 10% emitters for CO, HC, NO, and PM was found. These results imply that for an effective reduction of the four pollutants, inspection and maintenance (I/M) programs, including clean screening, should measure all four pollutants individually. Fleet average CO and HC concentrations determined by gaseous VERSS were compared with fleet average CO and HC concentrations measured at low-idle and at high-idle during local I/M tests for spark-ignition vehicles. The fleet average CO concentrations measured by I/M tests at either idle were about half of those measured by remote sensing. The fleet average high-idle HC concentration measured by I/M tests was about half of that measured by VERSS while low-idle I/M and VERSS HC average concentrations were in better agreement. For a typical vehicle trip, most of the fuel is burned during non-idle conditions. I/M measurements collected during idling conditions may not be a good indicator of a vehicle’s potential to be a high emitter. VERSS measurements, when the vehicle is under a load, should more effectively identify high emitting vehicles that have a large contribution to the mobile emissions inventory.     

Study on dynamic characteristics of vehicle gearbox under multi-boundary conditions

With the development of vehicle gearbox to high-power-density and high-speed, how to predict and optimize the dynamic characteristics of vehicle gearbox becomes increasingly prominent. Aiming at the vehicle gearbox, this paper comprehensively and deeply studies the dynamic characteristics under the multi-boundary conditions. The generation mechanism of the multi-source excitations triggering the gearbox vibration is analyzed firstly. The vibration transfer path of the gearbox is explored. Secondly, the engine excitation, the gear meshing excitation and the bearing support load are numerically calculated. According to the finite element method, a fluid-solid coupling finite element model of the gearbox body is established to predict the gearbox dynamic responses based on the Galerkin method and the Hamiltonian variational principle. Finally, the effects of the excitation condition, oil height and reinforcement forms on the vibration responses of the gearbox body are thoroughly studied by simulation. The analysis indicates that it not only helps to modify and improve the method of forecasting the gearbox dynamic response, and also provides the theoretical and technical guidance for the gearbox design and optimization.     

Target priority determination methods by interval-valued intuitionistic fuzzy sets with unknown attribute weights

The paper aims at the problem of multi-targets threat degree being hard to be evaluated accurately in complex air defense battlefield environments. Combined with multi-sensors information fusion and interval-valued intuitionistic fuzzy sets (IVIFS) theories, the target priority determination is studied. The score and accuracy functions of IVIFS are improved with thinking about the hesitating information in order to increase the rationality. Then, the influence factors of target priority and the nonlinear relationship between the influence factors and target priority are analyzed. Next, the algorithms for calculating the factor weights and sensor weights are given. Based on the theory of IVIFS and technique for order preference by similarity to an ideal solution (TOPSIS), two methods of target priority determination based on the IVIFS and TOPSIS are proposed. At last, an application example verifies the effectiveness and flexibility of the proposed algorithms.     

Exploring the impact of walk–bike infrastructure,safety perception,and built-environment on active transportation mode choice: a random parameter model using New York City commuter data

This study estimates a random parameter (mixed) logit model for active transportation (walk and bicycle) choices for work trips in the New York City (using 2010–2011 Regional Household Travel Survey Data). We explored the effects of traffic safety, walk–bike network facilities, and land use attributes on walk and bicycle mode choice decision in the New York City for home-to-work commute. Applying the flexible econometric structure of random parameter models, we capture the heterogeneity in the decision making process and simulate scenarios considering improvement in walk–bike infrastructure such as sidewalk width and length of bike lane. Our results indicate that increasing sidewalk width, total length of bike lane, and proportion of protected bike lane will increase the likelihood of more people taking active transportation mode This suggests that the local authorities and planning agencies to invest more on building and maintaining the infrastructure for pedestrians. Further, improvement in traffic safety by reducing traffic crashes involving pedestrians and bicyclists, will increase the likelihood of taking active transportation modes. Our results also show positive correlation between number of non-motorized trips by the other family members and the likelihood to choose active transportation mode. The model would be an essential tool to estimate the impact of improving traffic safety and walk–bike infrastructure which will assist in investment decision making.     

Tool for Predicting the Ultimate Bending Moment of Ship and Ship-Shaped Hull Girders

The present paper presents a historical review associated with the research works on hull girder strength of ship and ship-shaped structures. Then, a new program is developed to determine the ultimate vertical bending moment of hull girder by applying direct method, stress distribution method, and progressive collapse analysis method. Six ships and ship-shaped structures used in the benchmark study of International Ship and Offshore Structures Congress (ISSC) in 2012 are adopted as examples. The calculation results by applying the developed program are analyzed and compared with the existing results. Finally, the roles of the developed program and its further development are discussed.