Deflection test and transmission error measurement to identify hypoid gear whine noise

T-Hypoid gears are commonly used in rear-drive and 4WD (4 Wheel Drive) vehicle axles. Investigating their sensitivity to deflections is one of the most important aspects of their design and optimization procedures. Therefore, a deflection test was performed in this study in the actual gear mounting using completely processed gear. This test covered the full operating range of gear loads from “no load” to “peak load”. Under peak load, the contact pattern extended to the tooth boundaries without showing a concentration of the contact pattern at any point on the tooth surface. The transmission error was tested under an axle assembly triaxial-real-car-load condition.     

Haptic steering support for driving near the vehicle’s handling limits; skid-pad case

Current vehicle dynamic control systems from simple yaw control to high-end active steering support systems are designed to primarily actuate on the vehicle itself, rather than stimulate the driver to adapt his/her inputs for better vehicle control. The driver though dictates the vehicle’s motion, and centralizing him/her in the control loop is hypothesized to promote safety and driving pleasure. Exploring the above statement, the goal of this study is to develop and evaluate a haptic steering support when driving near the vehicle’s handling limits (Haptic Support Near the Limits; HSNL). The support aims to promote the driver’s perception of the vehicle’s behaviour and handling capacity (the vehicle’s internal model) by providing haptic (torque) cues on the steering wheel. The HSNL has been evaluated in (a) driving simulator tests and (b) tests with a vehicle (Opel Astra G/B) equipped with a variable steering feedback torque system. Drivers attempted to achieve maximum velocity while trying to retain control in a circular skid-pad. In the simulator (a) 25 subjects drove a vehicle model parameterised as the Astra on a dry skid-pad while in (b) 17 subjects drove the real Astra on a wet skid-pad. Both the driving simulator and the real vehicle tests led to the conclusion that the HSNL assisted subjects to drive closer to the designated path while achieving effectively the same speed. With the HSNL the drivers operated the tires in smaller slip angles and hence avoided saturation of the front wheels’ lateral forces and excessive understeer. Finally, the HSNL reduced their mental and physical demand.     

Methodology for bus structure torsion stiffness and natural vibration frequency prediction based on a dimensional analysis approach

Engineering bus design requires testing of bus structures prototypes in order to guarantee a certain level of strength and an appropriate static and dynamic behavior of the bus superstructure when exposed to road loads. However, experimental testing of real bus structures is very expensive as it requires expensive resources and space. If testing is done on a scale bus model the previous required expenses are considerably reduced. Therefore, a novel methodology based on dimensional analysis applied to bus structure prediction to evaluate the bus structure static and dynamic performance is proposed. The static performance is evaluated attending to torsion stiffness and the dynamic in terms of the natural vibration frequencies and rollover threshold. A scale bus has been manufactured and dimensionless parameters have been defined in order to project the results obtained in the scale bus model to a larger model. Validation of the proposed methodology has been carried out under experimental and finite element analysis.     

Impact technique for measuring global dynamic stiffness of engine mounts

Engine mounts are used for engine vibration isolation. The dynamic performance of the mount depends on the orientation. Measurements of the dynamic properties of engine mounts are usually performed in the axial direction because of the problem related to actuator loading direction and set up costs. Impact technique is developed here to measure the dynamic driving point stiffness and driving point shear stiffness of engine mount in a single setup. The compressive and shear frequency-dependent stiffnesses are obtained in the vertical orientation. A transformation matrix is used to calculate the frequency-dependent stiffnesses and loss factors in other orientations. Three different designs of engine mounts are used to verify the accuracy of the transformation model. The correlation coefficient between calculation and measurement results show R²≥ 0.995 along the X- and Y-axes. For the Z-axis, mounts B and C showed R²≥ 0.95 and mount A 0.687 ≤ R²≤ 0.791.     

Design and optimization of an LPG roller vane pump for suppressing cavitation

A roller vane type liquefied petroleum gas (LPG) pump was developed for a liquid phase LPG injection (LPLi) engine. Most of the LPG pumps used in the current LPLi engines are installed inside of the LPG tank, but this pump is intended to be installed outside of the LPG tank to overcome the difficulty of fixing an in-tank pump. Because LPG has a low boiling point and high vapor pressure, it usually causes cavitation in the pump and consequently deteriorates the flow rate of the pump. The purpose of this work is to optimize the design of the roller vane pump in order to suppress cavitation and increase the fuel flow rate by using a computational fluid dynamics (CFD) analysis. In order to achieve these goals, the intake port configuration and the rotor of the roller vane pump were redesigned and simulated using STAR-CD code. Computation was performed for six different models to obtain the optimized design of the roller vane pump at a constant speed of 2600 rpm and a constant pressure difference between the inlet and outlet of 5 bar. The computation results show that an increased intake port cross-section area can suppress cavitation, and the pump can achieve a higher flow rate when the rotor configuration is changed to increase its chamber volume. When the inlet pressure difference is 0.1 bar higher than the fluid saturation pressure, the pump reaches its maximum flow rate.     

柴油机故障诊断专家系统知识库设计

在分析柴油机故障诊断知识特点的基础上,采用模糊化方法对柴油机运行状态参数进行处理,采用综合型知识方式来表达柴油机故障诊断知识,采用多库多层次的方式组织知识库,并对知识库采取一系列方式进行管理与维护。应用表明,柴油机故障诊断专家系统的预报准确率较高,具有较强的实用性。     

Les systèmes de vélos en libre-service expliquent-ils le retour du vélo en ville ?

Many French and European cities have developed a bike sharing system since 2005. This policy may be explained in a great part by the success of the Velo??v in Lyon, which contributed to improve the image of cycling in the city. If bicycles, however, appear to find a new place in the city, one can wonder whether this is really due to bike sharing systems? What are the real uses of bicycles in contemporary cities, with or without such a system? To answer these questions, the paper starts with a literature review on bicycle in the city, to draw lessons from recent experiences of bike sharing systems. It then discusses the two cases of Lyon and Lille, which never had a bike sharing system on its own. The evolution of bicycle use is measured with a comparison of household transportation surveys in Lyon (1995 and 1998) and Lille (1998 and 2006). In both cities, the analysis reveals a rise in the proportion of healthiest citizens among urban bikers, as well as a return of bikes in dense areas. Bike sharing systems are part of such tendencies. They support them, but should not become a panacea for policies supporting bike use in the city.     

Comparative analysis of vehicle brake data in the ministry of transport test on the roller brake tester and on flat ground

This study performs a comparison between what occurs when braking on a Ministry of Transport (MOT) brake tester and on flat ground. The tire pressure is changed, but the other parameters remain constant. The results from this research and from the in-depth comparative study conducted by the mechanical engineering staff in the mechanical laboratory at the Miguel Hernández University in Elche have led to the following main conclusions: By varying the tire pressure, false results can be obtained with the MOT brake tester, which means that, if the tires are inflated at a low pressure but the brakes are in good condition, the vehicle will not pass the MOT. Conversely, if the brakes are in poor condition but the tire pressure is higher than what is recommended by the manufacturer, a false pass is produced. This article shows that the MOT brake testing equipment is often wrong and inexact, and the data and graphs presented prove that the tire pressure is a determining factor when assessing the condition of brakes.     

Perspectives on railway track geometry condition monitoring from in-service railway vehicles

This paper presents a view of the current state of monitoring track geometry condition from in-service vehicles. It considers technology used to provide condition monitoring; some issues of processing and the determination of location; how things have evolved over the past decade; and what is being, or could/should be done in future research. Monitoring railway track geometry from an in-service vehicle is an attractive proposition that has become a reality in the past decade. However, this is only the beginning. Seeing the same track over and over again provides an opportunity for observing track geometry degradation that can potentially be used to inform maintenance decisions. Furthermore, it is possible to extend the use of track condition information to identify if maintenance is effective, and to monitor the degradation of individual faults such as dipped joints. There are full unattended track geometry measurement systems running on in-service vehicles in the UK and elsewhere around the world, feeding their geometry measurements into large databases. These data can be retrieved, but little is currently done with the data other than the generation of reports of track geometry that exceeds predefined thresholds. There are examples of simpler systems that measure some track geometry parameters more or less directly and accurately, but forego parameters such as gauge. Additionally, there are experimental systems that use mathematics and models to infer track geometry using data from sensors placed on an in-service vehicle. Finally, there are systems that do not claim to measure track geometry, but monitor some other quantity such as ride quality or bogie acceleration to infer poor track geometry without explicitly measuring it.     

Parametric study of the main parameters influencing the catalytic efficiency of a diesel oxidation catalyst: Parameters influencing the efficiency of a diesel catalyst

This work studies the impact of five parameters: CO and HC engine-out emissions, space velocity, average value and profile of exhaust temperature, on Diesel CO and HC tail-pipe emissions. The first part of this work is conducted on a reactor and shows that both HC and CO light-off temperature increases with CO and HC input concentration. CO and HC initial concentration influence the adsorption/desorption capacities of HC only at high temperatures. Space velocity also influences CO and HC conversion efficiency. The second part of this work studies the impact of different combinations of HC and CO engine-out emissions on CO and HC conversion and tail-pipe emissions in the case of New European Driving Cycle. This part proposes that a Diesel oxidation catalyst must be mainly studied at the Urban Part of NEDC, as the CO and HC conversions are very high at the extra-urban part of NEDC. CO and HC conversion efficiencies are also dependent on exhaust temperature and catalytic volume. In the case of two different profiles of exhaust temperature with the same average temperature, CO and HC conversion efficiency is lower in the case of the smoother profile.