The impact of job assignment rules for straddle carriers on the throughput of container terminals

Straddle carriers represent a critical resource in the handling of containers within a container terminal. It is essential that they are deployed in an as efficient manner as possible. The research presented in this paper is motivated by the need to critically evaluate job assignment rules for straddle carriers that operate in a multiple straddle environment. This is achieved by developing a discrete event simulation model using industrial simulation software to model a container terminal located in Melbourne, Australia. The model accounts for variables such as the number of straddle carriers needed, the speed of straddle carriers, the arrival rate of trucks, and the job assignment rule. A principal finding of the study is that increasing the number of straddles in the present set‐up from 6 to 7 has a negligible effect on daily throughput. However, an increase in the number of straddles to 7 is expected to have a profound effect on reducing the average waiting time of trucks within the terminal from over 16 minutes to under 9 minutes, a decrease of 46.5%. However, a further increase in the number of straddles results in no further increase in daily throughput. It was observed that the throughput of the terminal is very sensitive to the speeds at which straddles travel. The management of the terminal has proposed a new heuristic job assignment rule for straddles, because the present rule does not assign the jobs to straddles closest to the truck requesting to load or unload a container. As a result a new heuristic job assignment rule was tested. The simulation results revealed that both the old and new rules performed equally well using performance indicators such as average container flow time, daily throughput, average waiting time of jobs, number of jobs in the queue, and straddle utilisation. Therefore, the new rule will not improve these performance measures if implemented     

软开关变流器的稳态分析(一)

讨论软开关变流器的稳态分析.由于分别由软开关变流器的Lr-Cr单元和大的L-C滤波器单元决定的快、慢固有频率的共存,通过启动瞬态仿真程序寻找软开关变流器的稳态解可能会造成繁琐的计算和收敛失败.由于采用了基于暂态分析的换相检测技术和基于补偿原理的换相分析技术,文章所提出的数值法显示了高可靠性和快速收敛性.对两个直流变换器、一台逆变器和一台功率因数补偿装置作的稳态分析,突出显示了仿真算法的良好性能.     

生物法处理生活污水脱氮除磷效果分析

通过对铁道部无锡干部培训基地（以下简称培训基地）的生活污水的生物法处理效果观察，探析兼氧／好氧生物处理系统的脱氮除磷原理并对影响处理效果因素进行分析。     

Simulated responses of the Gulf of Mexico hypoxia to variations in climate and anthropogenic nutrient loading

A mathematical model was used to simulate monthly responses of the Gulf of Mexico hypoxia to variations in climate and anthropogenic nutrient loading over a 45-year period. We examined six hypothetical future scenarios that are based on observed and projected changes in the Mississippi River discharge, Mississippi River nitrate concentrations, and ambient water temperatures. In particular, we investigated the implications of a 30% decrease in the Mississippi River nitrogen flux, which was recently proposed by the Mississippi River Watershed/Gulf of Mexico Hypoxia Task Force as a measure to reduce the size of the hypoxic zone. Model simulations suggest that the frequency of hypoxia in the northern Gulf of Mexico is highly sensitive to variations in riverine nitrate flux, but also to variations in freshwater discharge and ambient water temperatures. A 30% decrease in the Mississippi River nitrate flux, for example, would reduce the frequency of hypoxia by 37%. Nevertheless, a 20% increase the Mississippi River discharge, which may occur under some climate change scenarios, would produce an increase in the frequency of hypoxia of the same magnitude. Thus, if the potential climatic variations are taken into account, a 30% decrease in the nitrogen flux of the Mississippi River may not be sufficient to accomplish the proposed hypoxia management goal.     

Fleet deployment optimization for liner shipping Part 1. Background, problem formulation and solution approaches

The background and the literature in liner fleet scheduling is reviewed and the objectives and assumptions of our approach are explained. We develop a detailed and realistic model for the estimation of the operating costs of liner ships on various routes, and present a linear programming formulation for the liner fleet deployment problem. Independent approaches for fixing both the service frequencies in the different routes and the speeds of the ships, are presented.     

Comparison of HC species from diesel combustion modes and characterization of a heat-up doc formulation

This study summarizes engine speed and load effects on HC species emissions from premixed charge compression ignition (PCI) and conventional diesel combustion, and it evaluates diesel oxidation catalyst (DOC) formulations on a gas flow reactor for the purpose of diesel particulate filter regeneration or lean NO_x trap desulfation. HC emissions are sampled simultaneously by a Tedlar bag for light HC species and by a Tenax TA™ adsorption trap for semi-volatile HC species, and they are analyzed by gas chromatography with a flame ionization detector. The bulk temperature and residence time during combustion are key parameters that are important for understanding the effects of speed and load on engine-out HC emissions. The degree of post-flame oxidation is higher in PCI than in conventional combustion, and it is increased for PCI with a higher speed and load, as indicated by a lower fuel alkanes/THC ratio, a higher alkenes/fuel alkanes ratio, and a higher methane/THC ratio. Ethene and n-undecane are two representative HC species, and they are used as a surrogate mixture in the gas flow reactor to simulate PCI and conventional combustion with in-cylinder post fuel injection. Among the three DOC formulations tested, the catalyst with constituent precious metals of platinum and palladium (PtPd) showed the best light-off performance, followed by PtPd with an addition of cerium dioxide (PtPd+CeO₂), and platinum (Pt), regardless of exhaust compositions. Conventional combustion exhaust composition shows a lower light-off temperature than that of PCI, regardless of catalyst formulation.     

Thermal design of automobile exhaust based thermoelectric generators: Objectives and challenges

The potential for thermoelectric power generation (via waste heat recovery onboard automobiles) to displace alternators and/or provide additional charging to a vehicle battery pack has increased with recent advances in thermoelectric material processing. In gasoline fueled vehicles (GFVs), about 40% of fuel energy is wasted in exhaust heat, while a smaller amount of energy (30%) is ejected through the engine coolant. Therefore, exhaust-based thermoelectric generators (ETEG) have been a focus for GFV applications since the late 1980s. The conversion efficiency of modern thermoelectric materials has increased more than three-fold in the last two decades; however, disputes as to the thermal design of ETEG systems has kept their overall efficiency at limited and insufficient values. There are many challenges in the thermal design of ETEG systems, such as increasing the efficiency of the heat exchangers (hot box and cold plate), maintaining a sufficient temperature difference across the thermoelectric modules during different operating conditions, and reducing thermal losses through the system as a whole. This paper focuses on a review of the main aspects of thermal design of ETEG systems through various investigations performed over the past twenty years. This paper is organized as follows: first, the construction of a typical ETEG is described. The heat balance and efficiency of ETEG are then discussed. Then, the third section of this paper emphasizes the main objectives and challenges for designing efficient ETEG systems. Finally, a review of ETEG research activities over the last twenty years is presented to focus on methods used by the research community to address such challenges.     

Automotive structure vibration with component mode synthesis on a multi-level

The recursive component mode synthesis method (RCMS) has been implemented for the finite element analysis model of an automobile structure as an efficient free vibration analysis tool. The RCMS method is intended to obtain a better performance relative to the block Lanczos method, which is a traditional method in the industry of obtaining eigenvalues, while obtaining the acceptable accuracy. A numerical example of the automobile finite element model demonstrates the outstanding performance of RCMS compared to the block Lanczos method.     

A methodological approach for developing and assessing business models for flexible transport systems

Flexible transport services include a wide range of demand responsive transport systems that provide non-conventional passenger and freight transportation services. Several alternative business models varying according to the local market conditions, the socio-economic, legal, and institutional framework may be developed for the provision of Flexible Transport Systems (FTS). The objective of this paper is twofold: first to present an integrated methodological framework for developing and assessing alternative FTS business models and second to demonstrate its applicability to a case study regarding the prioritization of alternative FTS business models for the provision of flexible passenger transport services in Helsinki.

Exploring spatial variety in patterns of activity-travel behaviour: initial results from the Toronto Travel-Activity Panel Survey (TTAPS)

Studies of urban travel behaviour typically focus on weekday activities and commuting. This is surprising given the rising contribution of discretionary activities to daily travel that has occurred during the last few decades. Moreover, current understanding of the relationship between travel behaviour and land use remains incomplete, with little research carried out to explore spatial properties of activity-travel behaviour during the off-peak and weekend time periods. Weekend behaviours, for example, influenced by the availability of time and the spatiotemporal distribution of “weekend” destinations, likely produce spatially and temporally distinct activity-travel patterns. Using data from the first wave of the Toronto Travel-Activity Panel Survey (TTAPS), this paper examines an area of research that has received little attention; namely, the presence of spatial variety in activity-travel behaviour. The paper begins by looking at the extent to which individuals engage in spatially repetitive location choices during the course of a single week. Area-based measures of geographical extent and activity dispersion are then used to expose differences in weekday-to-weekend and day-to-day activity-travel patterns. Examination of unclassified activities carried out over a 1 week period reveals a level of spatial repetition that does not materialise across activities classified by type, travel mode, and planning strategy. Despite the inherent spatial flexibility offered by the personal automobile, spatial repetition is also found to be surprisingly similar across travel modes. The results also indicate weekday-to-weekend, and day-to-day fluctuations in spatial properties of individual activity-travel behaviour. These findings challenge the utility of the short-run survey as an instrument for capturing archetypal patterns of spatial behaviour. In addition, the presence of a weekday-to-weekend differential in spatial behaviour suggests that policies targeting weekday travel reduction could have little impact on travel associated with weekend activities.