On the observability of the fortnightly cycle of the Tagus estuary turbid plume using MODIS ocean colour images

Using three years (2003 to 2005) of MODIS-Aqua normalized water-leaving radiance at 551 nm this paper shows a fortnightly cycle in the Tagus estuary turbid plume. The Tagus estuary is one of the largest estuaries of the west coast of Europe and is located in the most populated area of Portugal, including the capital Lisbon. The turbid plume has been detected by the backscattering characteristics of the surface waters in the vicinity of the estuary mouth. In fortnightly scales, the turbid plume has smaller dimensions during and after neap tides and higher dimensions during and after spring tides. This is most probably associated with the fortnightly spring–neap tidal cycle and the consequent increase in turbidity inside the estuary during spring tides. During the summer weak spring tides (tidal amplitude approximately 2.5 m) no turbid plume is observed for an entire fortnightly cycle. Outside the summer months, precipitation, river discharge and winds, were found to increase the turbid area, but the fortnightly cycle appears to be superimposed on the large time-scale variability, and present throughout the year.     

On the numerical accuracy of the prediction of resistance coefficients in ship stern flow calculations

This article presents a study on the accuracy of the numerical determination of the friction and pressure resistance coefficients of ship hulls. The investigation was carried out for the KVLCC2 tanker at model- and full-scale Reynolds numbers. Gravity waves were neglected, i.e., we adopted the so-called double-model flow. Single-block grids with H–O topology were adopted for all the calculations. Three eddy viscosity models were employed: the one-equation eddy viscosity and the two-equation models proposed by Menter and the TNT version of the two-equation k-ω model. Verification exercises were performed in sets of nearly geometrically similar grids with different densities in the streamwise, normal, and girthwise directions. The friction and pressure resistance coefficients were calculated for different levels of the iterative error and for computational domains of different size. The results show that on the level of grid refinement used, it is possible to calculate the viscous resistance coefficients in H–O grids that do not match the ship contour with a numerical uncertainty of less than 1%. The differences between the predictions of different turbulence models were larger than the numerical uncertainty; however, these differences tended to decrease with increases in the Reynolds number. The pressure resistance was remarkably sensitive to domain size and far-field boundary conditions. Either a large domain or the application of a viscous–inviscid interaction procedure is needed for reliable results. This work was presented in part at the International Conference on Computational Methods in Marine Engineering—MARINE 2007, Barcelona, June 3–4, 2007.     

Influence of the slice position on chloride migration tests for concrete in marine conditions

Chloride migration tests are used to measure the concrete capacity to inhibit chloride attack. Many researchers carry out this test in a slice of concrete extracted from the central part of cylindrical specimens, discarding about 75% of the concrete used to mold the specimens. This fact generated the question: would it be possible to extract more slices from a same specimen without losing the confidence in the results? The main purpose of this work is to answer this question. Moreover, another aim of this study was to show the difference of chloride penetration between finished faces and the formwork surfaces of concrete beams and slabs. The results indicated that it is possible to use more slices of a single specimen for a chloride migration test. Moreover, it was demonstrated that there is a significant difference of chloride penetration between the finished surface and the formwork surface of the specimens.     

Water entry of a bow-flare ship section with roll angle

The two-dimensional water entry of a bow-flare ship section with constant roll angle, or heel angle, was studied by using a boundary element method. The fully nonlinear free surface conditions and exact body boundary conditions were satisfied. Nonviscous flow separation from the knuckles of the section or from the curved bottom could be simulated. The numerical calculations were compared with existing experimental results. First, the effects of roll angle were investigated and then the characteristics associated with large roll angles were examined in particular. The evolution of the free surfaces and the pressure distributions on the section surface are illustrated and the influence of nonviscous flow separation from the leeward section surface is discussed.     

Aggregating mobile object trajectories: cumulative time geographic density estimation for GPS data

We present new approaches that expand upon the time geographic density estimation (TGDE) framework previously employed to estimate potential path trees. In the past, TGDE metrics have identified possible locations an individual moving object may have passed between, given known origin and destination points. This paper utilizes a new form of TGDE to investigate taxicab GPS traces over a specified time horizon with position ‘gaps’. To this end, we propose a new extension to the TGDE framework, TGDE-C, which is used to determine the cumulative TGDE values for a group of GPS traces, at a given location. These metrics are applied to multiple taxis and allow for time of day analysis. Additionally, we combine these new extensions with existing TGDE metrics that allow us to determine how accessible individual or groups of vehicles are to urban opportunities.     

Numerical Simulation of Advanced Geological Forecasting Based on Multi- Source Seismic Interferometry北大核心CSCD

For existing advanced geological forecasting, the forecast distance is short and the test frequency is high, increasing test and construction risks. Since various methods have different requirements for the test environ-ment, preparation work can be tedious and result in a long construction time thereby affecting normal construction.A new advanced geological forecast technique based on multi-source seismic interferometry for tunnels is proposed.This technique uses the blast at one end of tunnel as a centrum and receives the signal at the other end of the tun-nel, therefore allowing advanced geological forecasting of the unexcavated tunnel part by relative processing and im-aging. A numerical simulation of this kind of geological forecasting using the finite difference method to simulate two kinds of unfavorable geological bodies (karst and a fault) predicted them accurately and verified the effective-ness and accuracy of this geological forecasting method. © 2018, Editorial Office of "Modern Tunnelling Technology". All right reserved.     

Analysis of Ground Response and Structure Stress Induced by PBA Method北大核心CSCD

The application of prefabricated tunnel technology has been become a new research field both in China and abroad. Based on the running tunnel between Yufuhe station and Wangfuzhuang station of Jinan rail transit line R1, a new prefabricated tunnel construction technology, the PBA method is presented. This paper makes a detailed discussion on section form, supporting scheme and construction process of the PBA method. In this study, 3D a new 3D numerical model for PBA method is presented by finite difference numerical simulation software Flac and the construction processes are modeled. The rule of ground surface settlement, ground deformation and structural stress caused by PBA method is studied in detail. Results show that the structure of PBA method can effectively control the deformation magnitude and scope. Stress concentration appears at the prefabricated connection parts and the reinforcement needs to check. The total assembled structure forms the load-bearing system after the completion of the lateral wall. The built-in depth of the precast pile and pile bottom grouting quality should to be ensured to control the displacement of the precast piles. The results of this study will be a useful reference for similar projects in the future. © 2018, Editorial Office of "Modern Tunnelling Technology". All right reserved.     

Effect of Seismic Parameters on the Safety Factor for an Underground Cavern北大核心CSCD

In order to quantitatively evaluate the safety of the surrounding rock of an underground cavern under seis-mic load, a comprehensive evaluation method for the stability of surrounding rock is proposed based on the general safety factor and point safety factor. A calculation method for the general safety factor of a cavern based on the prin-ciple of shear strength reduction of a rock mass is given, the run-through of the plastic zone between the main power-house and main transformer room is presented as a critical criterion for the overall instability of the cavern, and the general safety factor is obtained by searching for the reduction coefficient. A point safety factor calculation method based on the Mohr-Coulomb yield criterion is given. The influence of different seismic input parameters on the general safety factor of the cavern and the point safety factor of key positions are studied based on an underground power-house cavern of a hydropower station in Southwest China. The results show that the quantitative evaluation method for the stability of the surrounding rock based on the safety factor is feasible and can reflect the general safety de-gree and local safety degree of different positions of the cavern for different working conditions. It is found that the general safety factor of the cavern and the point safety factor of key positions decrease with an increase of the ampli-tude and duration of a seismic wave while they increase with an increase of the incident angle; additionally, the low frequency of a seismic wave has a great influence on the cavern while the high frequency has little effect. © 2018, Editorial Office of "Modern Tunnelling Technology". All right reserved.     

Design and Practice of Cloud Computing Platform for TBM Operation Information北大核心CSCD

The problems of TBM construction data loss, information barriers and absence of data mining have con⁃ strained the advancement of basic technologies in TBM field. Aimed at building a cloud computation platform for TBM operation information, a new concept of 3B, i. e. Born by digit, Born in format and Born to the cloud, was pre⁃ sented, the issues of information acquisition, transmission and storage during TBM operation were solved, and massive heterogeneous information intelligent transmission system and big data warehouse of TBM group were established. A structure model of cloud computation platform was designed by taking Hadoop system as ecosphere, and a cloud computation platform was built to deploy related algorithm, realizing on-line monitoring and data sharing, further⁃ more the data law mining of interaction of rock mass versus TBM machine was conducted based on big data tech⁃ nique, exploring the development direction of the information platform. © 2018, Editorial Office of "Modern Tunnelling Technology". All right reserved.     

Innovative strategies for urban car-sharing systems and a simulator to assess their performance

In this paper, three innovative car-sharing systems for urban areas are proposed, based on fleets of individual intelligent vehicles with three service characteristics: instant access, open-ended reservations and one-way trips. These features provide high flexibility but create an uneven distribution of vehicles among stations. Therefore, relocation of vehicles must be performed. Three different system procedures are proposed: in the first system, relocations are performed by users; in the other two, vehicles relocate automatically, thanks to their automation. In the first two systems, vehicles are accessible only at stations, whereas in the third they are also accessible along roads. In order to provide transport managers with a tool to test systems in different realities, an object-oriented simulator is developed. The simulation provides outputs of system performance, in terms of user waiting times and system efficiency. The proposed systems are simulated for the city of Genoa, in Italy, and a comparative analysis is presented.