A trial application of FSA methodology to the hatchway watertight integrity of bulk carriers

Formal safety assessment (FSA) is a formal, structured and systematic methodology, aimed at enhancing maritime safety, including protection of life, property and marine environment, by using risk and cost–benefit assessments. For the application of this methodology to the rule-making process, the International Maritime Organization (IMO) presented the Interim Guidelines, which describe procedures of FSA and inputs/outputs of each procedure in detail. This paper basically deals with an application of FSA methodology according to the IMO's Interim Guidelines to the hatchway watertight integrity of bulk carriers, which was carried out as a cooperative research between Korean Register of Shipping and Seoul National University. As results of this application study, 18 hazards are identified and 32 risk control measures are devised to reduce the associated risks. Potential risks, costs and benefits when some Risk Control Options are introduced are evaluated in monetary unit of US $. Finally, some discussions and recommendations based on experiences are also given for both future work and better application of this FSA methodology to the rule-making process.     

The receiving of chirp signals with frequency invariant beam response

1 Introduction1 The sensor array and the correlative signal processing methods have been adopted for the ability improvement of detection and orientation in modern sonar systems, and beamforming is a widely used tool in sensor array signal processing for …     

Effect of nozzle orifice diameter on diesel spray tip penetration according to various spray models for CFD simulation with widely varying back pressure

CFD simulations of spray tip penetration with the standard KIVA3V, ‘original gas jet’ and ‘Normal gas jet profile with breakup length formula’ (NGJBL) spray models were performed to investigate the effects of nozzle orifice size and ambient gas density combinations on the spray penetration. The accuracy of the CFD simulation results was estimated by comparing them with available experimental data. The ambient gas density was varied in 12 kg/m³ intervals from 12 to 69 kg/m³ for each nozzle orifice diameter. The nozzle orifice diameters used were 119, 140, 183 and 206 mm. A total of 20 cases in the CFD simulations were considered with combinations of the 4 nozzle orifice diameters and 5 ambient gas densities. CFD simulations with the NGJBL spray model were more accurate than those with either the standard KIVA3V or gas jet spray models as the nozzle orifice diameter and ambient gas density was increased. The NGJBL and original gas jet model is more effective in predicting the spray tip penetration near the nozzle tip region.     

Risk assessment framework for exposure of cargo and ports to natural hazards and climate extremes

There is an increase in risks and catastrophic losses in maritime transport including ports and cargo. Significant losses have been associated with large scale natural hazards, such as earthquakes, tsunami, cyclones, and other extreme weather events. This paper identifies the main gaps in understanding maritime risks in transportation research. The gaps are attributed to insufficient empirical work available from the maritime transport and logistics research community to guide multi-risk and natural hazards impact assessment on seaport and cargo. In addition, disaster studies communities have barely made adequate efforts to understand and assess port and cargo risks arising from multi-hazards and disaster events. This paper examines existing conceptual frameworks concerning exposure and risk assessments of natural catastrophe’s impacts. Furthermore, the paper identifies trends and gaps in risk assessment frameworks in the field of disaster studies that can be beneficial for maritime risk research. The authors propose a new risk assessment framework that can guide future research and multi-hazard risk assessment processes at different scales of maritime risks.     

Design framework for FlexRay network parameter optimization

Because the FlexRay protocol has more than 70 configuration parameters and these parameters correlate with each other, designing a FlexRay network is a complex and difficult task. In this study, we propose a design framework that optimizes the two main FlexRay network parameters that are highly relevant to the application algorithm. The design process is composed of two steps for optimizing parameters. In the first step, the static slot length is optimized using a frame-packing algorithm. This algorithm binds network signals into static frames based on their periods and signal groups. In the second step, the communication cycle length is optimally designed with frame-scheduling algorithm and worst-case reponse time analysis. Based on the frame-scheduling algorithm, the response times are analyzed. The proposed design framework was applied to a unified chassis control system as a case study, and the analytical results were verified.     

Damper modeling for dynamic simulation of a large bus with MR damper

In this study, a large bus is tested to measure its dynamic response by the single-lane change test and the rapid stop test. A full car model is established by ADAMS/Car for computer simulation. For multibody modeling of a large bus, user-defined templates are used in the simulation. Simulation results of the single-lane change test and the rapid braking test are compared to the results of the physical experiments, in which several sensors are installed to measure the vehicle’s responses. The results obtained from the simulation show good agreement with the tests’ results. A dynamic model for the MR(magnetic-rheological) damper is also developed by employing the Magic Formula model, which is widely used in the nonlinear modeling of a tire. Bump simulation of a full car with the MR damper is carried out to verify the performance of the MR damper. The comparison of the simulation results obtained with the MR damper model to the results obtained with the traditional passive damper model showed improved response of the vehicle with the MR damper.     

车辆阻挡效应对隧道火场燃烧及烟流之影响研究

近期国际曾发生多起重大隧道火灾灾难,隧道火灾安全议题已获得全球普便之重视。目前学术界与工程界多采用缩小尺寸实验或数值模拟方法对隧道火场环境进行研究与探讨。然不论实验或计算机模拟最重要的关键为能否充分地反应出实际隧道之火场情境,方能获致合理且有意义之研究成果。检视现今之隧道火害研究,可发现几乎所有的相关研究皆仅简化地假设火场上游无车辆回堵现象,此有违火场上游应发生车辆回堵之实际隧道火灾情境,因此将无法合理地模拟火场上游车辆阻挡风机气流对火场燃烧及烟流所造成之影响。针对此项尚待厘清之议题,本研究首先执行缩小尺寸实验,以均匀风速施加于隧道横断面模拟风机作动所产生之气流,探讨隧道塞车情境对火场燃烧所造成之影响。复执行全尺寸纵流式排烟模式(轴流风机)隧道火灾情境计算机数值模拟,针对火场上游是否有车辆回堵、回堵车体尺寸、火源与回堵车体距离等变因对火场燃烧、温度及烟流所造成之影响进行探讨。研究结果发现火场环境及烟流将受有、无车辆回堵、回堵车体大小及火源与车体距离等因素而有不同程度之影响。     

Improving the predictiveness of the quasi-d combustion model for spark ignition engines with flexible intake systems

Fast and predictive simulation tools are prerequisites for pursuing simulation based engine control development. A particularly attractive tradeoff between speed and fidelity is achieved with a co-simulation approach that marries a commercial gas dynamic code WAVE™ with an in-house quasi-dimensional combustion model. Gas dynamics are critical for predicting the effect of wave action in intake and exhaust systems, while the quasi-D turbulent flame entrainment model provides sensitivity to variations of composition and turbulence in the cylinder. This paper proposes a calibration procedure for such a tool that maximizes its range of validity and therefore achieves a fully predictive combustion model for the analysis of a high degree of freedom (HDOF) engines. Inclusion of a charge motion control device in the intake runner presented a particular challenge, since anything altering the flow upstream of the intake valve remains “invisible” to the zero-D turbulence model applied to the cylinder control volume. The solution is based on the use of turbulence multiplier and scheduling of its value. Consequently, proposed calibration procedure considers two scalar variables (dissipation constant C _β and turbulence multiplier C _M ), and the refinements of flame front area maps to capture details of the spark-plug design, i.e. the actual distance between the spark and the surface of the cylinder head. The procedure is demonstrated using an SI engine system with dual-independent cam phasing and charge motion control valves (CMCV) in the intake runner. A limited number of iterations led to convergence, thanks to a small number of adjustable constants. After calibrating constants at the reference operating point, the predictions are validated for a range of engine speeds, loads and residual fractions.     

Development of a navigation algorithm with dead reckoning for unmanned ground vehicles

A navigation algorithm is indispensable for Unmanned Ground Vehicles (UGVs). During driving, UGVs follow a global path. In this study, we propose a navigation algorithm using Real Time Kinematic (RTK)-Differential Global Positioning System (DGPS) units and encoders to complement global path planning. Sometimes GPS systems lose their signals and receive inaccurate position data due to many factors, such as edifice and barrier obstructions. This paper shows that GPS deviations can be solved using a Dead Reckoning (DR) navigation method with encoders and that position errors can be decreased through the use of RTK-DGPS units. In addition to this method, we will introduce a new waypoint update algorithm and a steering algorithm using RTK-DGPS units.     

Piston-temperature measuring system using electromagnetic induction with verification by a telemetry system

The development of an inner-piston-chamber temperature measurement system is a necessary step in engine development or when solving other fundamental problems related to automotive engines. There are various pre-existing measurement methods available, e.g., the linkage method, piston telemetry, templog, and the electromagnetic induction method. In this study, we first redesigned the coil sensor used in the electromagnetic induction method using PEEK and then used Taguchi methods to reduce the number of experiments in the development process and finally utilized piston telemetry via Bluetooth to verify the precision and accuracy of the redesigned PEEK coil sensor and electromagnetic induction method. The results displayed a reproducibility within 0.5 degrees and an accuracy within 2 degrees Celsius.