Fault detection method for electric parking brake (EPB) systems with sensorless estimation using current ripples

A fault detection method with parity equations is proposed in this paper. Due to its low cost implementation, the velocity of the motor is not measurable in electric parking brake (EPB) systems. Therefore, residuals are not reliable when estimating the motor velocity with a low-resolution encoder. In this paper, we propose a fault detection method with sensorless estimation using current ripples that estimates the position and velocity of the motor by detecting periodical oscillations of the armature current caused by rotor slots. In addition, this method can estimate the position and velocity of the motor with less computational effort than a state observer. Moreover, the method is less sensitive to motor parameters than model-based estimation methods. The effectiveness of this method is validated with experimental data, and the simulation results show that various faults have their own residual patterns. Therefore, we can detect the presence of faults by monitoring the residual signals.     

Development of electrostatic diesel particulate matter filtration systems combined with a metallic Flow-Through Filter and electrostatic methods

A 3000 cc diesel engine attached to an engine dynamo was used to test three newly developed electrostatic Diesel Particulate matter filtration Systems (DPS 1, 2, and 3) under four steady-state engine operating conditions: idle, 2000 rpm with no load, and 2000 rpm under 25% and 50% loads. Of the two developed alternatives, DPS 1 and DPS 2, DPS 2 comprises an ionization section, electrostatic field additional section and Flow-Through Filter (FTF), which achieved almost 90% removal of particulate matter (PM) under the engine’s operating conditions, and the efficiency of the FTF was maintained between 20% and 50%. Comparing the long-term performance of DPS 2 and DPS 3 (effectively a serial combination of two DPS 2s) with a commercially-available Diesel Particulate Filter (DPF), the DPS 2 and DPS 3 achieved almost the same efficiency for removing PM as the DPF but had significantly improved (75%∼90% lower) differential pressure drops.     

Development of a new sound metric for impact sound in a passenger car using the wavelet transform

Vehicles can experience impacts due to harsh road conditions. Contact with an uneven road surface causes vehicles to vibrate, which generates a loud impact sound. The attenuation of such noise is important because car passengers may complain about the impact noise. However, perfect removal of impact noise is not possible because most of it is caused by external conditions. More research is needed on the objective attributes of impact noise; however, the problem of impact noise is not a simple matter because impact noise is transient in nature and reaches a high level instantaneously. In this paper, a new objective attribute of impact noise is designed using the wavelet transform, which is appropriate for analyzing nonstationary signals, such as an impact signal. The usefulness of the new objective attribute, which is a sound metric, is examined by comparing the mean subjective ratings for real impact noise in passenger cars. The new sound metric has better correlation with the mean subjective rating than currently existing sound metrics.     

Design and implementation of a new clamping force estimator in Electro-Mechanical Brake systems

In this paper, an improved clamping force estimator is proposed for Electro-Mechanical Brake (EMB) systems by using the motor rotor position information and the hysteresis characteristics of mechanical parts in the EMB. A cascaded type of a force/position control system with a force sensor or an estimator was designed and implemented to control the clamping force and to keep the clearance gap in EMB systems. The EMB Hardware-In-the-Loop-Simulation (HILS) results show that the proposed force estimator yields better estimation performance than the existing estimator and that the clamping force control system based on the estimator can be also used for the fault tolerant control of the system.     

Experimental study on the impact characteristics of a sandwich composite with an aluminum foam core

The need for composites has been increasing in various industries because composites have good mechanical properties for their weight and superior stiffness and strength. The composites addressed in this study were multi-pore aluminum foam with a specific gravity of 1/10 composed of solid aluminum metal. This composite has excellent impact energy-absorption capability. In this study, impact tests on an aluminum foam core sandwich composite with a porous core were conducted to examine its mechanical properties. The specimen was a sandwich structure with an aluminum foam core, and different impact energies, such as 50J, 70J, and 100J, were applied to the specimen. Consequently, a maximum load of 5.5 kN occurred when the striker penetrated the upper face sheet in all experiments. The maximum load occurred at 4.2 ms for 50J, 3.5 ms for 70J, and 3.0 ms for 100J, indicating that the greater the impact energy was, the shorter the time was until the maximum load. After the maximum load occurred, that is, after the penetration of the upper face sheet, the striker penetrated 10 mm further, causing the core to be damaged in the 50J test, while the lower face sheet remained intact. In the 70J test, the striker penetrated the core and caused damage to the upper face sheet at 10 ms. Finally, in the 100J test, the striker penetrated both the upper face sheet and core and even the lower face sheet at 10 ms. Given the result above, the maximum load occurred when the striker penetrated the upper face sheet and the sandwich composite with aluminum foam core; the load then gradually decreased and then rapidly increased when the striker reached the lower face sheet, and the maximum load lasted slightly longer than the time required for the upper face sheet to be penetrated.     

欧洲客车设计

自然,欧洲客车设计也受到技术与生产的限制。自20世纪初到50年代的几十年时间里,大部分制造商在生产和销售适应于市场的车辆,这些车辆的可靠性非常好,无可挑剔,有些甚至可以说是难得的珍品。渐渐地,像所有经济领域一样,客车经济的信息增强了,单凭客车的外观与美学功能,就能对销     

Clamping performance of fastener in windshield wiper assembly using theoretical and experimental methods

Improper clamping of wiper arms can cause problems in the operation of the wiper. An excessive clamping force can cause damage to the wiper arm head. On the other hand, an insufficient clamping force can cause self-loosening of the nut. Given the lack of direct research on the clamping force of the fastener in wiper assembly, this study verifies the existing clamping performance of the fastener in windshield wiper assembly by theoretical and experimental methods. The theoretical calculation results show that all the clamping performance are satisfied under the general snow load condition. However, under the critical load condition, maximum assembly preload and safety margin against slipping are in disagreement with the standard values. This problem is solved by increasing the strength grade of the bolt. The experimental results show a reducing tendency of the clamping force during the snow durability test. However, this reducing clamping force during the 60,000 test cycles is acceptable. In the case of nut reusing more than two times possibly cause a problem of its loosening because of insufficient clamping force. Therefore, it is recommended that the nut should not be reused more than two times.     

Resource-aware integration of AUTOSAR-compliant ECUs with an empirical wcet prediction model

This paper presents an integration method of AUTOSAR-compliant ECUs which can evaluate resource constraints in an early-stage of development. There are three types of resources for an ECU (timing, memory, and interface) which should be carefully managed for successful ECU integration. The proposed method consists of three steps: measurement, prediction, and evaluation. In the first step, a method to measure resource factors for AUTOSAR-compliant software architecture is introduced. Based on the method, a worst-case execution cycle of a runnable, memory section usages of a software component, and interface of legacy ECUs can be obtained. In the second step, the obtained factors are quantitatively predicted according to the architectural designs of the integration ECU. In the case of the timing resource, the worst-case execution time of the integration ECU can be precisely predicted by a proposed empirical model. In the last step, the resource constraints such as CPU, memory, network utilizations can be evaluated with predicted resource factors before implementation. The proposed method was applied to the integration of an in-house engine management system composed of two ECUs. The method successfully provided quantitative measures to evaluate architectural designs of three different integration scenarios.     

Major sources of hydrocarbon emissions in a premixed charge compression ignition engine

Although premixed charge compression ignition (PCCI) combustion engines are praised for potentially high efficiency and clean exhaust, experimental engines built to date emit more hydrocarbons (HCs) and carbon monoxide (CO) than the conventional machines. These compounds are not only strictly controlled components of the exhaust gas of road vehicles but are also an energy loss indicator. The prime objective of this study was to investigate the major sources of the HCs formed in the combustion chamber of an experimental PCCI engine in order to suggest some effective technologies for HC reduction. In this study, to explore the dominant sources of HC emissions in both operation modes, a single cylinder engine was prepared such that it could operate using either conventional diesel combustion or PCCI combustion. Specifically, the contributions of the top-ring crevice volume in the combustion chamber and the bulk quenching of the lean mixture were investigated. To understand the influence of the shape and magnitude of the crevice on HC emissions, the engine was operated with 12 specially prepared pistons with different top-ring crevices installed one after another. The engine emitted proportionally more HCs as the depth of the crevice increased as long as the width remained narrower than the prevailing quench distance. The top-ring-crevice-originated exhaust HCs comprised approximately 31% of the total HC emissions in the baseline condition. In a series of tests to estimate the effects of bulk quench on exhaust HC emissions, intake air was heated from 300K to 400K in steps of 25K. With the intake air heated, HC and CO emissions decreased with a gradually diminishing rate to zero at 375K. In conclusion, the most dominant sources of HC emissions in PCCI engines were the crevice volumes in the combustion chamber and the bulk quenching of the lean mixtures. The key methods for reducing HC emissions in PCCI engines are minimizing crevice volume in the combustion chamber and maximizing intake air temperature allowed based on the permissible NOx level.     

Aerodynamic design optimization of rear body shapes of a sedan for drag reduction

This study proposes an aerodynamically optimized outer shape of a sedan by using an Artificial Neural Network (ANN), which focused on modifying the rear body shapes of the sedan. To determine the optimization variables, the unsteady flow field around the sedan driving at very fast speeds was analyzed by CFD simulation, and fluctuations of the drag coefficient (C _D ) and pressure around the car were calculated. After consideration of the baseline result of CFD, 6 local parts from the end of the sedan were chosen as the design variables for optimization. Moreover, an ANN approximation model was established with 64 experimental points generated by the D-optimal methodology. As a result, an aerodynamically optimized shape for the rear end of the sedan in which the aerodynamic performance is improved by about 5.64% when compared to the baseline vehicle is proposed. Finally, it is expected that within the accepted range of shape modifications for a rear body, the aerodynamic performance of a sedan can be enhanced so that the fuel efficiency of the sedan can be improved. The YF SONATA, a sedan manufactured by Hyundai Motors Corporate, played a major role in this research as the baseline vehicle.