Study on shaft alignment of propulsion shafting system depending on single reaction force supporting position of aft stern tube bearing

Journal of Marine Science and Technology - Trends of large-scale ships have seen propulsion shaft and propeller sizes increase. This has enabled shafts to have greater stiffness, yet has caused...     

基于SoftPLC的船舶主机遥控物理仿真模拟器设计

模拟器以一艘1600 TEU集装箱船使用的Autochief IV主机控制系统作为原型,采用SoftPLC实现对船舶主机遥控物理仿真模拟器的控制。利用组态软件PIMS作为上位机开发平台,实现数据的存储及功能的完善。在模拟器上可以进行各种相关的训练操作,达到培训学员的目的。     

Hybrid process of fabricating high-quality micro wine-glass fused silica resonators

A new hybrid method, which combines improved glass-blown technology with wet etching, is reported to fabricate micro wine-glass resonators with high-quality fused silica. The optimum placement is compared to achieve the resonators with good shell shape. The typical shell diameter is about 4mm and its thickness covers from dozens to hundreds of micrometers. The etching rates in corrosion solutions with different ratios and at different thicknesses of hemispherical shells are studied. We also conclude how to precisely control the thickness. The corrosion solutions with different ratios of HF solution to NH₄F solution make the spherical shells rougher in different degrees. The best roughness is 0.581 nm in the 1: 8 ratio corrosion solution while the original roughness is 0.537 nm. This fact shows that the resonator remains atomically smooth surface. Based on the glassblowing spherical fused silica structure, the thickness of the resonator is effectively controlled by buffered oxide etch (BOE) technology according to the measured etching rate. The measured resonant frequency of the hemispherical shell at ambient pressure and room temperature is 1.75 kHz of rocking mode which is close to the simulated frequency. Using such a low-cost hybrid approach, we can fabricate high-quality microscale resonators in batch.     

Purification effects of C2Cl6 on A00 aluminum

The effects of several fluxes on purification, microstructures and properties of A00 aluminum have been studied. The experimental results and analyses indicate that many cracks and large porosities exist in the surface film above the melt purified by C₂Cl₆ and that the film is floc and mostly composed of Al₂O₃ and pure aluminum, which carries many carbon particles and AlCl₃ not fully volatilized. And then over 50% (mass fraction) of the all-melting residue is pure aluminum, which is one of the major reasons for high melting loss. Moreover, because of a mass of gas bubbles and a state of seethe, there are many inclusions which size is under 10 ??m in the microstructure of A00 aluminum purified with C₂Cl₆ or fluxes containing C₂Cl₆. With this purifying method, the aluminum crystal grains are extended along the radius that was observed firstly and the average crystal size of A00 aluminum are about 100?C150 ??m. In addition, small size inclusions have little affected on tensile strength and micro inclusions under 10 ??m have little affected on elongation.     

Novel experimental strategy for high resolution AFM imaging of membrane-associated bacterial toxins

Bacterial pore-forming toxins （PFTs） are essential virulence factors of many human pathogens. Knowl- edge of their structure within the membrane is critical for an understanding of their function in pathogenesis and for the development of useful therapy. Atomic force microscopy （AFM） has often been employed to structurally interrogate many membrane proteins, including PFTs, owing to its ability to produce sub-nanometer resolution images of samples under aqueous solution. However, an absolute prerequisite for AFM studies is that the samples are single-layered and closely-packed, which is frequently challenging with PFTs. Here, using the prototypical member of the cholesterol-dependent cytolysin family of PFTs, perfringolysin O （PFO）, as a test sample, we have developed a simple, highly robust method that routinely produces clean, closely-packed samples across the entire specimen surface. In this approach, we first use a small Teflon well to prepare the supported lipid bilayer, remove the sample from the well, and then directly apply the proteins to the bilayer. For reasons that are not clear, bilayer preparation in the Teflon well is essential. We anticipate that this simple method will prove widely useful for the preparation of similar samples, and thereby enable AFM imaging of the greatest range of bacterial PFTs to the highest possible resolution.     

Estimation of delay variability at signalized intersections for urban arterial performance evaluation

Urban arterial performance evaluation has been broadly studied, with the major focus on average travel time estimation. However, in view of the stochastic nature of interrupted flow, the ability to capture the characteristics of travel time variability has become a critical step in determining arterial level of service (LOS). This article first presents a stochastic approach that integrates classic cumulative curves and probability theories in order to investigate delay variability at signalized intersections, as a dominant part of the link travel time variability. This serves as a basis for arterial travel time estimation, which can be obtained through a convolution of individual link travel time distributions. The proposed approach is then applied in the estimation of travel time along one arterial in Shanghai, China, with abundant automatic vehicle identification (AVI) data sources. The travel time variability is evaluated thoroughly at 30-min intervals, with promising results achieved in comparison to the field measurements. In addition, the estimated travel time distributions are utilized to illustrate the probability of multiple LOS ranges, namely, reliability LOS. The results provide insights into how we might achieve a more reliable and informative understanding of arterial performance.     

Modelling,simulation and applications of longitudinal train dynamics

ABSTRACT

Significant developments in longitudinal train simulation and an overview of the approaches to train models and modelling vehicle force inputs are firstly presented. The most important modelling task, that of the wagon connection, consisting of energy absorption devices such as draft gears and buffers, draw gear stiffness, coupler slack and structural stiffness is then presented. Detailed attention is given to the modelling approaches for friction wedge damped and polymer draft gears. A significant issue in longitudinal train dynamics is the modelling and calculation of the input forces – the co-dimensional problem. The need to push traction performances higher has led to research and improvement in the accuracy of traction modelling which is discussed. A co-simulation method that combines longitudinal train simulation, locomotive traction control and locomotive vehicle dynamics is presented. The modelling of other forces, braking propulsion resistance, curve drag and grade forces are also discussed. As extensions to conventional longitudinal train dynamics, lateral forces and coupler impacts are examined in regards to interaction with wagon lateral and vertical dynamics. Various applications of longitudinal train dynamics are then presented. As an alternative to the tradition single wagon mass approach to longitudinal train dynamics, an example incorporating fully detailed wagon dynamics is presented for a crash analysis problem. Further applications of starting traction, air braking, distributed power, energy analysis and tippler operation are also presented.     

A signal-based fault detection and classification method for heavy haul wagons

This paper proposes a signal-based fault detection and isolation (FDI) system for heavy haul wagons considering the special requirements of low cost and robustness. The sensor network of the proposed system consists of just two accelerometers mounted on the front left and rear right of the carbody. Seven fault indicators (FIs) are proposed based on the cross-correlation analyses of the sensor-collected acceleration signals. Bolster spring fault conditions are focused on in this paper, including two different levels (small faults and moderate faults) and two locations (faults in the left and right bolster springs of the first bogie). A fully detailed dynamic model of a typical 40t axle load heavy haul wagon is developed to evaluate the deterioration of dynamic behaviour under proposed fault conditions and demonstrate the detectability of the proposed FDI method. Even though the fault conditions considered in this paper did not deteriorate the wagon dynamic behaviour dramatically, the proposed FIs show great sensitivity to the bolster spring faults. The most effective and efficient FIs are chosen for fault detection and classification. Analysis results indicate that it is possible to detect changes in bolster stiffness of ±25% and identify the fault location.     

VVL耦合喷油策略对GDI汽油机混合气形成的影响

利用三维仿真软件Ansys Fluent建立了GDI汽油机的仿真计算模型,就变气门升程耦合不同喷油策略对缸内气流运动和混合气形成的影响进行了模拟计算。结果表明,与大气门升程工况相比,小气门升程工况的缸内湍流运动强度、燃油蒸发和湿壁情况以及点火时刻混合气质量都明显改善;在小气门升程工况,采用两段喷油会缩短油气混合时间,过度推迟二次喷油时刻会恶化混合气质量和燃油湿壁情况;在大气门升程工况,两段喷油会改善混合气均匀性,随着二次喷油时刻推迟,燃油蒸发量增加,湿壁情况加剧,混合气质量得到改善;小气门升程工况下采用二次喷油时刻为470°曲轴转角,前后两次喷油量比例为7∶3的两段喷油方案在燃油蒸发和湿壁以及点火时刻缸内混合气质量这几个方面的效果都很好,是最合理的方案。     

基于ARENA的双车道超车视距设计风险评价

通过计算机仿真软件ARENA模拟双向两车道路段上不同的超车视距长度下的超车行为,并建立风险指标。风险指标主要根据超车动作结束时,超越车与对向车辆间的最短时间距离确定。一共确定了六个风险等级,用于评价不同设计时速下的各种PSD长度的风险。利用此方法可以很直接的评价超车视距设计的优劣。