Vibration path analysis and optimal design of the suspension for brake judder reduction

Brake judder is abnormal vibration, which is mainly generated by uneven contact between the brake disc and pad. The abnormal vibration from BTV (Brake Torque Variation) is transferred to the suspension and the steering system during braking. In this paper, judder simulation is carried out using a multi-body dynamic analysis program to analyze the relationship between judder and the transfer mechanism, which consists of the suspension and the steering system. In order to verify the analytical model, test results are compared with the simulation results. A sensitivity analysis is also carried out. In addition, an optimization method is presented for judder reduction, using the design of experiments.     

Development of engine control using the in-cylinder pressure signal in a high speed direct injection diesel engine

Emission regulations are becoming more stringent and remain a principal issue for vehicle manufacturers. Many engine subsystems and control technologies have been introduced to meet the demands of these regulations. For diesel engines, combustion control is one of the most effective approaches for reducing not only engine exhaust emissions but also cylinder-by-cylinder variation. However, the high cost of pressure sensors and the complex engine head design for additional equipment present difficulties for manufacturers. In this paper, cylinder pressure-based engine control logic is introduced for a multi-cylinder high speed direct injection (HSDI) diesel engine. The time for 50% of the mass fraction to be burned (MFB50) and the IMEP are valuable for determining the combustion status. These two in-cylinder quantities are measured and applied to the engine control logic. Fuel injection timing is controlled to adjust the operating MFB50 to the target MFB50 using PID control logic, and the fuel injection quantity is controlled to adjust the measured IMEP to the desired IMEP. The control logic is demonstrated at steady state and during transient conditions and is applied to an NEDC mode test.     

A comparative study of aggregate and disaggregate gravity models using Seoul metropolitan subway trip data

Abstract

Existing origin constrained and doubly constrained gravity models have not been compared, theoretically or empirically, in terms of their forecasting power. Due to the newly advanced technology of intelligent transport systems, the expanded data presently available have made various models more comparable in terms of forecasting power. This paper uses archived automatic passenger counting (APC) data for urban rail in the Seoul metropolitan area. The APC data contains information about each trip's origin, destination, ticket type, fare, and distance on a daily basis. The objective of this paper is to compare the goodness-of-fit of aggregate and disaggregate gravity modeling using these data. A Hyman aggregate gravity model is used as the aggregate model without the spatial effect. The disaggregate model adopts a multinomial logit as the destination choice model with the spatial effect. In general, while the formulation of aggregate and disaggregate gravity model models are similar, the calibration and parameter estimation methods of the two models are different. As a result, this empirical study demonstrates that the variation in goodness-of-fit and forecasting power largely depends on the estimation method and selected variables. The forecasting power of the disaggregate modeling approach outperforms that of the aggregate model. This paper further confirms that spatial arrangement plays important roles in gravity modeling.     

Effect of cetane enhancer on spray and combustion characteristics of compressed ignition type LPG fuel

This research investigated the spray and combustion characteristics of compressed ignition type LPG fuel when a cetane number enhancing additive was applied to a constant volume chamber. Because LPG has a lower cetane number, DTBP and alpha olefin were added to the LPG (100% butane) to enhance the cetane number and viscosity. By adding the cetane enhancer, stable combustion over the wide range of the ambient conditions was possible as well. According to the blending rates of DTBP and alpha olefin, various proportions of LPG blended fuels were obtained. In a constant volume chamber, a high speed digital camera was also employed to visualize the combustion characteristics of LPG fuel. The combustion pressures and heat-release rates of the LPG blends were also compared at various ambient pressures. As the results of measurements of exhaust emissions, CO and HC were reduced considerably, but CO₂ was increased by blending LPG with DTBP and alpha olefin.     

Optimum distribution of yaw moment for unified chassis control with limitations on the active front steering angle

This paper describes an optimum distribution method for yaw moment for use with unified chassis control (UCC) with limitations on the active front steering (AFS) angle. Although the UCC has been assumed to have no AFS angle limitation in the literature, a physical limitation exists in real applications. To improve upon the previous method, a new optimum distribution method for yaw moment is proposed that takes this limitation into account. This method derives an optimum longitudinal/lateral force using the Karush-Kuhn-Tucker (KKT) optimality condition, and a simulation is performed to validate the proposed method. The simulation results indicate that the limitation on the AFS angle increases longitudinal braking force and, therefore, reduces the vehicle speed and the side-slip angle.     

利用大型动载荷试验评价车辆铝合金车体疲劳强度

介绍了用模拟实际动载荷的大型试验方法来评价城市交通运输车辆铝合金车体疲劳强度的必要性,并对车体的疲劳破坏进行了研究。     

Effects of mixture stratification on HCCI combustion of DME in a rapid compression and expansion machine

Compression ignition of homogeneous charges in internal combustion (IC) engines is expected to offer high efficiency of DI diesel engines without high levels of NOx and particulate emissions. This study is intended to find ways of extending the rich limit of HCCI operation, one of the problems yet to be overcome. Exhaust emissions characteristics are also explored through analyses of the combustion products. DME fuel, either mixed with air before induction or directly injected into the combustion chamber of a rapid compression and expansion machine, is compressed to ignite under various conditions of compression ratio, equivalence ratio, and injection timing. The characteristics of the resulting combustion and exhaust emissions are discussed in terms of the rate of heat release computed from the measured pressure, and the concentrations of THC, CO, and NOx are measured by FT-IR and CLD. The experimental data to date show that operation without knock is possible with mixtures of higher equivalence ratio when DME is directly injected rather than when it is inducted in the form of a perfectly homogeneous fuel-air mixture. Although fuel injected early in the compression stroke promotes homogeneity of the DME-air mixture in the cylinder, it causes the mixture to ignite too early to secure good thermal efficiency and knock-free operation at high loads. Low temperature reactions occur at about 660K regardless of the fueling methods, fuel injection timing and equivalence ratio. The main components of hydrocarbon emissions turned out to be unburned fuel (DME), formaldehyde and methane.     

Performance analysis of a CVT clutch system for a hybrid electric vehicle

In this study, the performance of a CVT clutch system for a hybrid electric vehicle was investigated. To analyzed the vehicle performance at restart, the restart delay and driveshaft torque was investigated by simulations and experiments. It was found from the simulation results that the vehicle restart response depends on the clutch pressure buildup time to the point where the clutch torque begins to overcome the vehicle road load, and driving comfort at restart is directly related to the rate change of the clutch pressure.     

Characteristics of wireless sensor network for full-scale ship application

In this study, basic experiments regarding the wireless sensor network were conducted on a 3,000-ton-class training ship as the first step in applying the ubiquitous technology to a real ship. Various application fields of the technology in terms of the provision of safety and convenience on a ship were identified through these experiments. To efficiently adopt the ubiquitous technology for ship application, it is necessary to identify the state-of-the-art ubiquitous technology and to prepare countermeasures against the harsh environment of a ship. The characteristics of the wireless sensor network were investigated on a test bed ashore as well as on a real ship before full-scale ship application. In particular, experimental results concerning communication depth, data transmission ratio, and battery consumption in a sensor node are described in detail.