Special issue: Importance of public transport

The transport demand in most major cities around the world can only be met with a high‐quality public transport system. The requirements on bus, rail, underground and tram systems are manifold with reliability and efficiency as the key factors. The service operating hours and the size of the network are often extended in order to serve the needs better. Further, most metropolitan areas are trying to provide more incentives for citizens to leave the car at home and use the local transit systems instead. The reasons are well known. Not only does a public transport system only make economical sense if it is well used, but most urban areas with a high car‐dependency face at least three major problems; safety, congestion, and pollution (noise and air pollution, land separation, etc.). It is generally recognised that to decrease car usage and to increase public transport usage a stick & carrot approach is needed. The London congestion‐charging scheme is an example since all revenues collected by the scheme are put into the improvement of bus and underground services.     

Analysis process of a steering system using a concept model for idle vibration

This paper describes the development of an optimal design process for a steering column system and supporting system. A design guide is proposed at the initial concept stage of the development process to obtain sufficient stiffness of the steering system while reducing the idle vibration sensitivity of the system. Case studies on resonance isolation are summarized, where vibration modes among the systems are separated by applying a vibration mode map at the initial stage of the design process. This study also provides design guidelines for an optimal dynamic damper system using a CAE (computer aided engineering) analysis. The damper FE (finite element) model is added to the vehicle model to analyze the relation between the frequency and the sensitivity of the steering column system. This analysis methodology makes it possible to achieve target performance in the early design stage and reduction of damper tuning activity after the proto car test stage. Through the proposed steering column system development process, a lightweight vehicle with high stiffness is possible prior to the proto build stage. Furthermore, the improved process is expected to contribute to reducing the overall development period and the number of proto car tests necessary to achieve the desired steering system performance.     

Prediction of fatigue life and estimation of its reliability on the parts of an air suspension system

Air suspension systems have been implemented in various commercial vehicles, such as buses and special purpose trucks, because of the comfortable ride and easy height control. An evaluation of the durability of vehicle parts has been required for service life and safety starting in the early stages of design. The cyclic load applied to the vehicle can cause fatigue failure of parts, such as the suspension frame. This paper presents a method to predict the fatigue life of the suspension frame at the design stage of the air suspension system used in a heavy-duty vehicle. To estimate the fatigue life using the SN method, the Dynamic Stress Time History (DSTH) is necessary for the part of interest. DSTH can be obtained from the results of the flexible body dynamic analysis using the Belgian road simulation and the Modal Stress Recovery (MSR) method. Furthermore, the reliability of the predicted fatigue life can be evaluated by considering the variations in material properties. The probability and distribution of the expected life cycle can be obtained using experimental design with a minimum number of simulations. The advantage of using statistical methods to evaluate the life cycle is the ability to predict replacement time and the probability of failure of mass-produced parts. This paper proposes a rapid and simple method that can be effectively applied to the design of vehicle parts.     

Lane-following method for high speed autonomous vehicles

This paper presents a steering control method for lane-following in a vehicle using an image sensor. With each image frame acquired from the sensor, the steering control method determines target position and direction, and constructs a travel path from the current position to the target position either as an Arc-path or S-path. The steering angle is calculated from the travel path thus generated, and the vehicle follows the travel path via motor-control. The method was tested using a vehicle dubbed as KAV (Korea Autonomous Vehicle) along an expressway (Seoul Inner Beltway) trajectory with a variety of radii (50 m ∼ 300 m) while traveling at a speed of 60 km/h to 80 km/h. Compared with an experienced human driver, the method showed little much difference in performance in terms of lane-center deviation. The proposed method is currently employed for high speed autonomous driving as well as for stop and go traffic.     

卵砾石层管推进工程超挖及卡钻对管材与土壤互制行为的影响研究

非明挖工法在都市施作时,常因困难地质(如卵砾石层)或障碍物而造成施工困难、工期延误或发生灾损。本文主要针对非明挖施工法里的管推进施工法(Pipe-jacking Method),探讨管推进工法施工时可能遭遇的困难,以及施工困难状况下之管材土体互制行为。探讨的施工困难包括超挖、挤压、卡钻等问题。本研究针对超挖范围、卡钻位置、阻力大小以及推进力施加位置等,以ABAQUS有限元素软件进行三维数值仿真,探讨直线推进施工中的问题。     

Development of electrostatic diesel particulate matter filtration systems combined with a metallic Flow-Through Filter and electrostatic methods

A 3000 cc diesel engine attached to an engine dynamo was used to test three newly developed electrostatic Diesel Particulate matter filtration Systems (DPS 1, 2, and 3) under four steady-state engine operating conditions: idle, 2000 rpm with no load, and 2000 rpm under 25% and 50% loads. Of the two developed alternatives, DPS 1 and DPS 2, DPS 2 comprises an ionization section, electrostatic field additional section and Flow-Through Filter (FTF), which achieved almost 90% removal of particulate matter (PM) under the engine’s operating conditions, and the efficiency of the FTF was maintained between 20% and 50%. Comparing the long-term performance of DPS 2 and DPS 3 (effectively a serial combination of two DPS 2s) with a commercially-available Diesel Particulate Filter (DPF), the DPS 2 and DPS 3 achieved almost the same efficiency for removing PM as the DPF but had significantly improved (75%∼90% lower) differential pressure drops.     

Application of slim A-pillar to improve driver’s field of vision

The importance of vehicle safety cannot be exaggerated in today’s mobile societies. Many manufacturers, associates related to vehicles and universities make an effort to improve vehicle safety by developing new technologies, applying high strength steel to the body structure etc. However, the majority of these efforts are focused on decreasing injury. It is absolutely important to minimize injury, but a more important aspect is coping with vehicle accidents. That is, As undeniably important as it is to minimize potential injuries, it is critical that experts focus on developing ways to keep drivers out of situations likely to lead to crashes in the first place. The purpose of this paper is to determine what the most critical factor is when coping with an unfamiliar driving situation. The answer is to provide a wide-open field of vision, especially for the driver. The driver’s field of vision is obstructed by the vehicle’s A-pillar. To solve this, the A-pillar obstruction angle, which is the angle between the driver’s eyes and the A-pillar should be decreased. This paper purposes three-methods for decreasing this angle structurally and applying a slim A-pillar which is as the best solution to decrease the A-pillar obstruction angle and ensure the drivers field of vision at the same time     

Design and optimization of an LPG roller vane pump for suppressing cavitation

A roller vane type liquefied petroleum gas (LPG) pump was developed for a liquid phase LPG injection (LPLi) engine. Most of the LPG pumps used in the current LPLi engines are installed inside of the LPG tank, but this pump is intended to be installed outside of the LPG tank to overcome the difficulty of fixing an in-tank pump. Because LPG has a low boiling point and high vapor pressure, it usually causes cavitation in the pump and consequently deteriorates the flow rate of the pump. The purpose of this work is to optimize the design of the roller vane pump in order to suppress cavitation and increase the fuel flow rate by using a computational fluid dynamics (CFD) analysis. In order to achieve these goals, the intake port configuration and the rotor of the roller vane pump were redesigned and simulated using STAR-CD code. Computation was performed for six different models to obtain the optimized design of the roller vane pump at a constant speed of 2600 rpm and a constant pressure difference between the inlet and outlet of 5 bar. The computation results show that an increased intake port cross-section area can suppress cavitation, and the pump can achieve a higher flow rate when the rotor configuration is changed to increase its chamber volume. When the inlet pressure difference is 0.1 bar higher than the fluid saturation pressure, the pump reaches its maximum flow rate.     

Development of a new sound metric for impact sound in a passenger car using the wavelet transform

Vehicles can experience impacts due to harsh road conditions. Contact with an uneven road surface causes vehicles to vibrate, which generates a loud impact sound. The attenuation of such noise is important because car passengers may complain about the impact noise. However, perfect removal of impact noise is not possible because most of it is caused by external conditions. More research is needed on the objective attributes of impact noise; however, the problem of impact noise is not a simple matter because impact noise is transient in nature and reaches a high level instantaneously. In this paper, a new objective attribute of impact noise is designed using the wavelet transform, which is appropriate for analyzing nonstationary signals, such as an impact signal. The usefulness of the new objective attribute, which is a sound metric, is examined by comparing the mean subjective ratings for real impact noise in passenger cars. The new sound metric has better correlation with the mean subjective rating than currently existing sound metrics.     

Effects of injection parameters on the spray characteristics of swirl and slit injectors using the Mie-scattering method

We investigated the effects of injection parameters such as injection pressure, ambient pressure, and ambient temperature on spray characteristics. We calculated the turbulence occurring point (t _c ), defined as the time required to generate a vortex, and the deceleration point (t _b ), defined as the time when spray penetration begins to decelerate, to elucidate the breakup mechanism of the test injectors. The spray velocity coefficient (C_v) was obtained to evaluate the spray characteristics. As the ambient pressure increases in the case of a slit injector, C_v decreases. We investigated the effects of nozzle tip shape according to injection pressure, ambient pressure, and fuel properties on spray characteristics and provide a C_v value of 0.38 for the swirl injector with a spray angle of 60° and the slit injector under atmospheric conditions. The value of C_v in the case of a slit injector was reduced by increasing the ambient pressure. Our results suggest that C_v of a swirl injector is constant regardless of changes in ambient pressure, injection pressure, and fuel properties. On the other hand, C_v of a slit injector is altered by changes in ambient pressure.