A study of the environmental impacts of intelligent automated vehicle control at intersections via V2V and V2I communications

This article presents a novel intersection traffic management system for automated vehicles and quantifies its impact on fuel consumption and greenhouse gas emissions of CO₂ relative to traditional traffic signal and roundabout intersection control. The developed intelligent traffic management (ITM) techniques, which are based on a spatiotemporal reservation scheme, ensure that vehicles proceed through the intersection without colliding with other vehicles while at the same time reducing the intersection delay and environmental impacts. Specifically, the spatiotemporal reservation scheme provides each vehicle a collision-free path that is decomposed into a speed profile along with navigational instructions. The integration of the developed microscopic traffic simulator with instantaneous emission model, provides improved assessments of the environmental impact of traffic control strategies at intersections. The simulator architecture integrates several ITM algorithms, vehicle sensors, V2V/V2I communications, and emission and fuel consumption models. Each vehicle is modeled by an agent and each agent provides information depending on the specific vehicle sensors. The ITM system is supported by V2V and V2I communications, allowing the exchange of information among vehicles and infrastructure. The data include the estimated vehicle position and speed. Compared with traditional traffic management techniques, the simulation results prove that the proposed ITM system reduces CO₂ emissions significantly. The research also shows that these reductions are more significant when the traffic flow increases.     

不同加载幅值下考虑层间界面条件和侧向剪力作用的柔性铺面响应

该文进行了一个三维有限元参数量化的粘弹性路面响应研究,由于不同的轮胎配置:双轮和宽基轮胎在3种温度(5、25和40℃)和两种速度(8、72 km/h);还有影响路面响应的3种因素:移动车轮荷载幅值(连续,梯形),层间界面条件(简单的摩擦和粘弹性模型)和横向力共同对路面响应的影响进行了研究.研究发现连续加载幅值,不但可以模拟路面对运动轮荷载的响应,并且是一种比目前使用的梯形荷载幅值更准确的研究模型.粘弹性模型极大地提高了双轮胎对预测路面的响应,而简单的摩擦模型更接近宽基轮胎的实地测量.侧向剪力是积极改善预测轮底的表面磨损和底部热拌沥青(沥青)基层的较小程度上的应变.研究表明:使用连续加载幅值和非均匀压力分布模拟移动轮,侧向剪切力和适当的界面摩擦可显著改善有限元模型对车辆加载路面响应的预测能力.     

不同外加剂对OGFC混合料路用性能的影响

OGFC为开级配沥青混合料,主要由粗集料嵌挤组成,在世界各地越来越广泛地用于铺筑路面.OGFC混合料可以增大路表面渗透性,减少噪音,增强表面摩擦力,尤其是在潮湿条件下.该文主要研究不同外加剂对OGFC路用性能的影响,其混合料分别由再生聚乙烯改性沥青(RPEB)、橡胶粉改性沥青(CRMB)和70#基质沥青+纤维与矿料拌和而成.并分别采用析漏试验、肯塔堡飞散试验、渗水试验、劈裂试验、静态模量试验,车辙试验和抗滑试验评估OGFC混合料的路用性能.结果表明:纤维和聚合物可以有效地减小OGFC离析的可能性,混合料每面击实50次能相应地提高磨耗性和其他相关的性能.改性沥青混合料的抗拉强度比(TSR)低于纤维+基质沥青混合料的抗拉强度比.     

Review of flywheel based internal combustion engine hybrid vehicles

Hybrid vehicles of different configurations and utilizing different energy storage systems have existed in development for many decades and more recently in limited production. They can be grouped as parallel, series or complex hybrids. Another classification is micro, mild and full hybrids which makes the distinction on the basis of functionality. The common energy storage systems in hybrid vehicles are batteries, supercapacitors and high speed flywheels. This paper aims to review a specific type of hybrid vehicle which involves the internal combustion engine (ICE) as the prime mover and the high speed flywheel as an energy storage device. Such hybrids are now attracting considerable interest given their potential for low cost. It is hence timely to produce a review of research and development in this subject. The flywheel is coupled to the drive line with a continuous variable transmission (CVT). The CVT can be of various types such as electrical, hydraulic or mechanical but usually in this case it is a non-electrical one. Different configurations are possible and the paper provides a timeline of the development of such powertrains with various examples. These types of hybrid vehicles have existed as prototypes for many decades and the authors believe that their development has reached levels where they can be considered serious contenders for production vehicles.     

Experimental study on the impact characteristics of a sandwich composite with an aluminum foam core

The need for composites has been increasing in various industries because composites have good mechanical properties for their weight and superior stiffness and strength. The composites addressed in this study were multi-pore aluminum foam with a specific gravity of 1/10 composed of solid aluminum metal. This composite has excellent impact energy-absorption capability. In this study, impact tests on an aluminum foam core sandwich composite with a porous core were conducted to examine its mechanical properties. The specimen was a sandwich structure with an aluminum foam core, and different impact energies, such as 50J, 70J, and 100J, were applied to the specimen. Consequently, a maximum load of 5.5 kN occurred when the striker penetrated the upper face sheet in all experiments. The maximum load occurred at 4.2 ms for 50J, 3.5 ms for 70J, and 3.0 ms for 100J, indicating that the greater the impact energy was, the shorter the time was until the maximum load. After the maximum load occurred, that is, after the penetration of the upper face sheet, the striker penetrated 10 mm further, causing the core to be damaged in the 50J test, while the lower face sheet remained intact. In the 70J test, the striker penetrated the core and caused damage to the upper face sheet at 10 ms. Finally, in the 100J test, the striker penetrated both the upper face sheet and core and even the lower face sheet at 10 ms. Given the result above, the maximum load occurred when the striker penetrated the upper face sheet and the sandwich composite with aluminum foam core; the load then gradually decreased and then rapidly increased when the striker reached the lower face sheet, and the maximum load lasted slightly longer than the time required for the upper face sheet to be penetrated.     

Computational and experimental investigation of the unsteady flow structures around automotive outside rear-view mirrors

The unsteady flow field around two automotive outside rear-view mirrors is investigated. This study includes comprehensive experimental and computational approaches in order to characterize the complex flow structures in the wake of the mirrors. The experiments were carried out in a wind tunnel which included the measurements of the instantaneous and averaged velocity fields as well as mean and unsteady surface pressure distributions. The simulations were performed using Large Eddy Simulation (LES). The LES approach (particularly with the dynamic subgrid viscosity model) provided good agreements with the experiments for the velocity and the surface pressure distributions. The experimental and the computational results of this study will be used as a benchmark to validate the current and the future CFD development and the subsequent aero-acoustic computations.     

Research on control strategy for differential steering system based on H mixed sensitivity

The differential steering system (DSS) of electric wheel vehicle gets rid of the restrictions of traditional steering system completely. As an ideal steering technology, it not only realizes the perfect combination of the road feel and the steering portability, but also realizes the harmony and unification between the steering maneuverability and safety. The structure and basic theory of the DSS of electric wheel vehicle are discussed in this paper. Based on these, the dynamic model of the steering system is built. Considering of the uncertainties and disturbances existing in the model, the H_∞ mixed sensitivity control theory is applied to achieve better tracking performance and road feel in the process of steering. Then, a H_∞ mixed sensitivity controller is designed to restrain the effect of the road disturbance and model uncertainties. The simulation results indicate that the DSS with the designed controller can effectively restrain the effect of noises and disturbances caused by random motivation from road, torque sensor measurement and model parameter uncertainty, and enable the driver to obtain satisfactory road feel.     

Dual extended Kalman filter for vehicle state and parameter estimation

The article demonstrates the implementation of a model-based vehicle estimator, which can be used for combined estimation of vehicle states and parameters. The estimator is realised using the dual extended Kalman filter (DEKF) technique, which makes use of two Kalman filters running in parallel, thus 'splitting' the state and parameter estimation problems. Note that the two problems cannot be entirely separated due to their inherent interdependencies. This technique provides several advantages, such as the possibility to switch off the parameter estimator, once a sufficiently good set of estimates has been obtained. The estimator is based on a four-wheel vehicle model with four degrees of freedom, which accommodates the dominant modes only, and is designed to make use of several interchangeable tyre models. The paper demonstrates the appropriateness of the DEKF. Results to date indicate that this is an effective approach, which is considered to be of potential benefit to the automotive industry.     

Quasi steady-state aerodynamic model development for race vehicle simulations

Presented in this paper is a procedure to develop a high fidelity quasi steady-state aerodynamic model for use in race car vehicle dynamic simulations. Developed to fit quasi steady-state wind tunnel data, the aerodynamic model is regressed against three independent variables: front ground clearance, rear ride height, and yaw angle. An initial dual range model is presented and then further refined to reduce the model complexity while maintaining a high level of predictive accuracy. The model complexity reduction decreases the required amount of wind tunnel data thereby reducing wind tunnel testing time and cost. The quasi steady-state aerodynamic model for the pitch moment degree of freedom is systematically developed in this paper. This same procedure can be extended to the other five aerodynamic degrees of freedom to develop a complete six degree of freedom quasi steady-state aerodynamic model for any vehicle.