Flamelet combustion model for stratified EGR distribution in a diesel engine

Numerous research has been devoted to finding a method to simultaneously reduce NOx and soot emissions from diesel engines. In-cylinder EGR stratification is a technique that simultaneously reduces NOx and soot using a nonuniform EGR distribution in the combustion chamber. To study the potential of in-cylinder EGR stratification, a new combustion model is required that considers the non-uniform EGR distribution and the chemical kinetics. In this study, a new combustion model, the Flamelet for Stratified EGR (FSE) model, was developed to consider the non-uniform in-cylinder gas distribution based on chemical kinetics. The concept of the FSE model is based on using multiple flamelets with the multizone concept. To describe the non-uniform gas distribution, the combustion chamber is divided into several zones by oxygen concentration at the start of injection. Then, the flamelet equations are solved at the boundary of each zone. The final species mass fraction of each cell is calculated using linear interpolation between two results from the boundaries. In this paper, the FSE model was validated under in-cylinder EGR stratification conditions, and then, the potential of in-cylinder EGR stratification was studied by using the FSE model. The effect of in-cylinder EGR stratification was verified under various injection timing, engine speed, and road conditions with optimized engine geometries. The results shows simultaneous NOx and soot reductions under the stratified EGR condition.     

一种最佳的汽车混合动力总成

介绍了对混合动力总成进行优化的建模及仿真工具《汽车快速性能优化及报告工具包—汽车系统模块(RAPTOR^TM—VSM)软件包》，指出了优化混合动力总成需在混合动力发动机、电动机、电池、超级电容器、动力总成配置和自动／手动变速器(AMT)控制器等方面做的工作。     

工厂火灾,爆炸场所危险度综合评价法

为减少火灾事故，介绍了“工厂火灾、爆炸场所危险度综合评价法”，“道氏法”是该法的基础。分析了“道氏法”的不足，而提出了固定危险和现实补偿的综合性计算方法。还通过实例记述了新方法的优点、基本原理和应用方法。该法能用于评价工厂企业危险设备、装置与场所的火灾、爆炸危险程度。     

不同外加剂对OGFC混合料路用性能的影响

OGFC为开级配沥青混合料,主要由粗集料嵌挤组成,在世界各地越来越广泛地用于铺筑路面.OGFC混合料可以增大路表面渗透性,减少噪音,增强表面摩擦力,尤其是在潮湿条件下.该文主要研究不同外加剂对OGFC路用性能的影响,其混合料分别由再生聚乙烯改性沥青(RPEB)、橡胶粉改性沥青(CRMB)和70#基质沥青+纤维与矿料拌和而成.并分别采用析漏试验、肯塔堡飞散试验、渗水试验、劈裂试验、静态模量试验,车辙试验和抗滑试验评估OGFC混合料的路用性能.结果表明:纤维和聚合物可以有效地减小OGFC离析的可能性,混合料每面击实50次能相应地提高磨耗性和其他相关的性能.改性沥青混合料的抗拉强度比(TSR)低于纤维+基质沥青混合料的抗拉强度比.     

Development of a new sound metric for impact sound in a passenger car using the wavelet transform

Vehicles can experience impacts due to harsh road conditions. Contact with an uneven road surface causes vehicles to vibrate, which generates a loud impact sound. The attenuation of such noise is important because car passengers may complain about the impact noise. However, perfect removal of impact noise is not possible because most of it is caused by external conditions. More research is needed on the objective attributes of impact noise; however, the problem of impact noise is not a simple matter because impact noise is transient in nature and reaches a high level instantaneously. In this paper, a new objective attribute of impact noise is designed using the wavelet transform, which is appropriate for analyzing nonstationary signals, such as an impact signal. The usefulness of the new objective attribute, which is a sound metric, is examined by comparing the mean subjective ratings for real impact noise in passenger cars. The new sound metric has better correlation with the mean subjective rating than currently existing sound metrics.     

Fault detection method for electric parking brake (EPB) systems with sensorless estimation using current ripples

A fault detection method with parity equations is proposed in this paper. Due to its low cost implementation, the velocity of the motor is not measurable in electric parking brake (EPB) systems. Therefore, residuals are not reliable when estimating the motor velocity with a low-resolution encoder. In this paper, we propose a fault detection method with sensorless estimation using current ripples that estimates the position and velocity of the motor by detecting periodical oscillations of the armature current caused by rotor slots. In addition, this method can estimate the position and velocity of the motor with less computational effort than a state observer. Moreover, the method is less sensitive to motor parameters than model-based estimation methods. The effectiveness of this method is validated with experimental data, and the simulation results show that various faults have their own residual patterns. Therefore, we can detect the presence of faults by monitoring the residual signals.     

Vibration transmission reduction from a centrifugal turbo blower in a fuel cell electric vehicle

This paper presents a multi-body flexible dynamic analysis of a centrifugal turbo blower for a fuel cell electric vehicle (FCEV) based on the application of computer-aided engineering (CAE) to predict the acceleration at the mount position of the blower. This predicted acceleration is validated by using the measured acceleration data. The numerical simulation for the multi-body flexible dynamics of the blower is used not only to identify the most effective mount among four mounts in an FCEV by controlling the complex stiffness of the isolator, but also to suggest the range of complex stiffness of the isolator at the most effective mount. This numerical simulation technology can be useful for the estimation of the variation of vibration transmission for the structural modification of the turbo blower.     

Prediction of the dimensional deformation of the addendum and dedendum after the warm shrink fitting process using a correction coefficient

The warm shrink fitting process is generally used to assemble automobile transmission parts (shafts/gears). However, this process causes a deformation in the addendum and dedendum of the gear depending on the fitting interference and gear profile, and this deformation causes additional noise and vibration between the gears. To address these problems, the warm shrink fitting process is analyzed by considering the error in the dimensional deformation of the addendum and dedendum found when comparing the results of a theoretical analysis and finite element analysis (FEA). A correction coefficient that reduces this error is derived through an analysis of the difference in the cross-sectional area between the shapes used for the theoretical analysis and that of the actual gear, and a closed-form equation to predict the dimensional deformation of the addendum and dedendum is proposed. The FEA method is proposed to analyze the thermal-structural-thermal coupled field analysis of the warm shrink fitting process (heating-fitting-cooling process). To verify the closed-form equation using the correction coefficient, measurements are made of actual helical gears used in automobile transmissions. The results are in good agreement with those given by the closed-form equation.     

Major sources of hydrocarbon emissions in a premixed charge compression ignition engine

Although premixed charge compression ignition (PCCI) combustion engines are praised for potentially high efficiency and clean exhaust, experimental engines built to date emit more hydrocarbons (HCs) and carbon monoxide (CO) than the conventional machines. These compounds are not only strictly controlled components of the exhaust gas of road vehicles but are also an energy loss indicator. The prime objective of this study was to investigate the major sources of the HCs formed in the combustion chamber of an experimental PCCI engine in order to suggest some effective technologies for HC reduction. In this study, to explore the dominant sources of HC emissions in both operation modes, a single cylinder engine was prepared such that it could operate using either conventional diesel combustion or PCCI combustion. Specifically, the contributions of the top-ring crevice volume in the combustion chamber and the bulk quenching of the lean mixture were investigated. To understand the influence of the shape and magnitude of the crevice on HC emissions, the engine was operated with 12 specially prepared pistons with different top-ring crevices installed one after another. The engine emitted proportionally more HCs as the depth of the crevice increased as long as the width remained narrower than the prevailing quench distance. The top-ring-crevice-originated exhaust HCs comprised approximately 31% of the total HC emissions in the baseline condition. In a series of tests to estimate the effects of bulk quench on exhaust HC emissions, intake air was heated from 300K to 400K in steps of 25K. With the intake air heated, HC and CO emissions decreased with a gradually diminishing rate to zero at 375K. In conclusion, the most dominant sources of HC emissions in PCCI engines were the crevice volumes in the combustion chamber and the bulk quenching of the lean mixtures. The key methods for reducing HC emissions in PCCI engines are minimizing crevice volume in the combustion chamber and maximizing intake air temperature allowed based on the permissible NOx level.     

Performance optimization of CVT for two-wheeled vehicles

Continuously Variable Transmission (CVT) is one of the most promising automotive transmission technologies because of its continuously variable gear ratio and reduced shift shock. CVT is different from Manual Transmission and Automatic Transmission, and it is possible to operate the power source in its high efficiency region with CVT in the drive train. Several types of CVT exist that can be categorized based on the mechanism of power transmission, such as the belt pulley, traction drive, and hydrostatic types. This paper investigates the belt pulley CVT, which consists of a thrust actuator, driver pulley, belt, driven pulley, and preload spring of the output shaft. A complete CVT is constructed, and based on that a simulation program that analyzes the static performance of a CVT is implemented in Matlab/Simulink. From these simulation results, methods for improving the efficiency of the CVT are discussed. The coefficient of the torque capacity factor is proposed as affecting the matching between a power source and a CVT, and methods for improving the matching effect are also investigated.