Comparative Analysis of Calculation Methods for Jacking Force of Jacking Pipes北大核心CSCD

Jacking force is the most important parameter in jacking pipe engineering, and reasonable calculation of jacking forces plays an important role in safe and smooth pipe jacking construction. There are many calculation methods for pipe jacking force at present, and the calculation results may be affected to some extent by different cal⁃ culation methods. For this reason, calculation methods of jacking force (frictional resistance) were collected and a comparative analysis was conducted with aspects to the advantages, disadvantages and applicabilities. The results show that as for the jacking force calculated by empirical formulae, the soil layer classifications corresponding to giv⁃ en frictional force per unit area and relevant factors to be considered are different, and the values of frictional force per unit area between pipe and soil in the same soil layer are also different; as for the jacking force calculated by theo⁃ retical formulae, the calculation methods for vertical earth pressure at crown are different and much effected by the pipe buried depth; as for the jacking force calculated by numerical simulation, the selected theories for the simula⁃ tion program and the construction factors to be considered during simulation are different. © 2018, Editorial Office of "Modern Tunnelling Technology". All right reserved.     

Soil Body Deformation Caused by Construction of a Double-Line Shield Tunnel with Multiple Factors北大核心CSCD

Considering the influence of many factors (soil loss, frontal additional thrust, the friction force of the shield shell and the additional grouting force), a method for improving the uniform soil body movement model is pro-posed, and a mechanical calculation model is established to study the calculation method for soil body deformation caused by double-line parallel shield driving. Based on the Mindlin solutions of elastic mechanics, the theoretical solutions for soil body deformations caused by the last three factors are calculated; considering the uniform soil body movement model, the theoretical solutions for soil body deformations caused by soil loss are calculated, then the to-tal theoretical solutions for soil body deformations under multiple factors are obtained by means of superposition. The vertical surface settlement, vertical horizontal displacement, and vertical displacements of the soil body at different depths of Hangzhou Metro Line 1 are calculated to analyze the variation laws. Meanwhile the influential factors for horizontal displacement variation are studied. The research shows that with a change of depth, the settlement of the soil body changes within the scope of 10 to 13 m in the horizontal direction near where the maximum settlement occurs;the direction of the horizontal displacement of the soil body changes with a change of the positional relationship be-tween the calculation points and the tunnel; and with an increase of interval J for the two tunnels, the horizontal dis-placement of the soil body of a deep double-line tunnel decreases while the displacement near the surface changes slightly. © 2018, Editorial Office of "Modern Tunnelling Technology". All right reserved.     

“工厂法”沉管隧道早期性能的足尺试验研究

由于沉管隧道管段体积大、结构形式复杂、施工工艺复杂,容易因温度、收缩以及约束等原因,造成管段结构在预制阶段出现危害性裂缝,进而影响结构的服役性能和耐久性能。文章依托在建港珠澳大桥沉管隧道工程实例,开展了足尺试验,对"工厂法"沉管管节关键部位的温度和应变发展实施了监测,分析对比了温度发展规律和应变发展规律。分析结果表明:在早期因混凝土水化热引起温度上升,整个管段结构膨胀受拉,温度到达峰值后逐渐下降,结构也收缩恢复;但由于混凝土自收缩等因素的存在,结构最终收缩受压。研究所提供的试验结果可作为深入进行数值分析的一个基础。     

公路隧道双洞互补式通风适用性分析

为研究公路隧道双洞互补式通风的适用性,文章基于隧址海拔和温度、隧道长度和纵坡、隧道交通量和交通组成、隧道双洞间距等因素对互补式通风负荷比及通风效果的影响进行计算分析。研究结果表明:当隧道上下行通风负荷比大于1.5或隧道单向纵坡绝对值在1.5%~2.0%之间时,适宜采用互补式通风;隧道长度在4.5~6 km之间时,采用双洞互补式通风最经济实用;交通量和交通组成的影响关系显示隧道大型车混入率在35%~50%之间时宜考虑采用互补式通风;双洞隧道适合采用互补式通风的最小间距为30 m。     

集中排烟隧道近火源顶板热参数理论预测

由于集中排烟模式能较好地控制上下游烟气的扩散范围,故被广泛应用于长大隧道设计中。文章针对小尺度火灾,建立了集中排烟隧道火源热烟羽受限发展理论模型,与已有火灾实验结果进行对比,完成了理论模型的验证,预测了顶板下方最高烟气温升、偏移距离等热参数。预测结果表明:火灾强度一定时,烟气最大温升随等效风速增加而急剧下降,且火灾强度对烟气温升的影响也较为显著;当等效风速超过1.5 m/s时,最大温升变化趋缓直至恒定;等效风速较小时,羽流未发生明显偏移,随着等效风速进一步增大,偏移距离明显增大,其变化速率随火灾强度的增大而减小。经回归整理得到了顶板下方烟气最大温升、偏移距离的无量纲准则关联式。     

探讨危旧桥梁加固的有关技术问题

随着国家经济建设脚步的加快,路桥的建设技术也在不断的进步,危旧桥梁的加固处理也成为桥梁建设的热点话题之一。因为公路车流量的增多,在上世纪末建设的桥梁一直都存在过载使用的问题,过多的重型车辆对危旧桥梁的使用也是一项巨大的考验。在一些使用年限比较久的桥梁中,出现了桥体老化现象。本文就危旧桥梁加固的有关技术问题进行了探讨。     

预制中隔墙施工技术在轨交区间隧道内的应用

轨交区间隧道中隔墙采用预制与现浇结合的方式进行施工,在国内尚属首例。以上海轨交16号线南段工程为实例,阐述了在施工过程中如何在小空间范围内进行拼装中隔墙、临时支撑的安装及浇筑等工艺,可为今后类似工程施工提供借鉴。     

穿越古滑坡川主寺隧道围岩破坏特征及稳定性研究

文章以川主寺隧道所处的工程地质条件为基础,通过现场调研分析了隧道围岩变形破坏形式主要为坍塌、掉块以及剥落.围岩稳定性三维有限元数值模拟结果显示,碎裂围岩自稳能力差,围岩变形以弹塑性变形、松弛变形为主;H型钢拱架支护结构对碎裂围岩稳定性起到积极的作用,并通过典型洞段现场位移监测数据分析结果得以证实.     

轴对称解对隧道衬砌水压力计算的适用性研究

文章根据渗流理论推导了隧道衬砌水压力的轴对称解,并利用数值分析方法研究了轴对称解对不同形状隧道断面与浅埋隧道的适用性.研究结果表明:轴对称解适用于非圆形隧道断面衬砌水压力的估算;隧道断面形状对衬砌水压力折减系数的影响较小,可以忽略不计,其影响大小主要由衬砌与围岩的渗透系数比值决定.对于浅埋低水头隧道,用轴对称解计算的毛洞流量Qm与数值解比较,其误差较大,最大误差为36.5％;但用来计算衬砌水压力p1以及衬砌后水流量Q1时,误差相对较小,最大误差为6.3％,特别是利用轴对称解得出的衬砌水压力值与利用数值解得出的衬砌水压力特征值最大误差仅为3.4％.     

宁波轨道交通1号线车站深基坑设计与施工监测的对比分析

本文对宁波市轨道交通1号线东门口站所进行的土层性质分析、设计方案的优化、设计计算结果与实际施工监测数据的对比分析,对于宁波地区轨道交通车站深基坑设计具有积极意义,使设计与施工能互为印证、互为比较、互为参考,为后续地下三层车站的设计和施工提供了宝贵的实践经验。