跳频通信系统抗跟踪式干扰性能研究

对于跳频通信系统,跟踪式干扰是一种较有效的干扰样式。分析了干扰方程并进行了仿真,认为干扰机配置位置必须在干扰椭圆内跟踪式干扰才能有效实施干扰,提高跳速是对抗跟踪式干扰的一种有效方法。     

Model Test on Grouting Law in Dynamic Water-Rich Sand Layers by the Electric Resistance Method北大核心CSCD

In order to study the diffusion law of grouting slurry in the water-rich sand layer under flowing water conditions, a grouting test model consisting of a main test system, a grouting system, and a measurement system was developed. And for detecting the diffusion scope of the grouts, a new resistivity method was proposed. It is found that the relationship between grouting pressure and grouting rate during the test is strong. Under hydrodynamic conditions, the grouting slurry diffuses elliptically. Due to gravity and the effect of the upper water flow, the center of gravity of the ellipsoid is below the grouting outlet, and the grouting effectively improves the physical and mechanical properties of water-rich sand bodies. At the same time, the resistivity method has a good application effect on the detection of grouting diffusion range. The range of slurry diffusion obtained by the resistivity method is basically consistent with the boundary of the stone body after excavation, indicating that the resistivity method is reliable for detection of grouting range in dynamic water-rich sand layer. © 2018, Editorial Office of "Modern Tunnelling Technology". All right reserved.     

X80管线钢管的屈强比对其失效评估曲线的影响

X80及以上级别管线钢管的高屈强比是工程应用中的一个突出问题,失效评估曲线是其安全评定的重要依据。文中通过单轴拉伸和断裂韧性试验建立了高屈强比X80管线钢管的特征失效评估图及拟合方程。结果表明：随着钢管屈强比升高,失效评估曲线的截至线（最大载荷比）降低;高、低屈强比钢管的评估曲线在载荷比大于某一临界值时发生分离,且高屈强比钢管的评估曲线处于低屈强比钢管的评估曲线之下;高屈强比钢管的选择3评估曲线比选择1和选择2曲线更偏于安全。     

不同驾驶操作行为对车辆燃油消耗量的影响分析

针对车辆驾驶员普遍存在盲目换挡、急加速等不良驾驶行为的现象,研究采用发动机台架试验和道路试验相结合的方法,对汽车起步、换挡时机的选择、加速、减速、车速控制等典型的驾驶操作行为展开研究,通过对不同驾驶操作行为燃油消耗的分析,规范了汽车驾驶操作行为。     

高速公路ETC车道防邻道及跟车干扰研究

在ETC车道系统中,相邻两个ETC车道之间的OBU与RSU相互影响,RSU与非本车道上的OBU进行通讯并完成交易,引起邻道干扰;工程实施、设备等原因引起跟车干扰,造成ETC收费失败。针对存在的问题,分析工程安装、设备原因,提出切实可行的解决方案,保证ETC车道功能的正确性、完整性,是交通运输行业节能减排绿色发展成果之一。     

恶劣天气红外热成像行人检测方法研究

为了提高智能汽车在恶劣天气对行人检测的速度和精度,本文提出一种基于YOLO V4的红外热成像行人检测方法.通过迁移学习对YOLO V4模型进行再训练,可快速而准确地实现恶劣道路环境的行人检测.     

Tool for Predicting the Ultimate Bending Moment of Ship and Ship-Shaped Hull Girders

The present paper presents a historical review associated with the research works on hull girder strength of ship and ship-shaped structures. Then, a new program is developed to determine the ultimate vertical bending moment of hull girder by applying direct method, stress distribution method, and progressive collapse analysis method. Six ships and ship-shaped structures used in the benchmark study of International Ship and Offshore Structures Congress (ISSC) in 2012 are adopted as examples. The calculation results by applying the developed program are analyzed and compared with the existing results. Finally, the roles of the developed program and its further development are discussed.     

An exploratory investigation of the impact of ramp metering on driver acceleration behavior

Ramp metering has been proven as an effective freeway management strategy; however, the impact of ramp metering on drivers' acceleration behavior has not been fully investigated. A better understanding of acceleration behavior changes with ramp metering is critical to the adequate design of ramp metering facilities. In this study, drivers' speed and acceleration data were collected at two representative metered ramps in Los Angeles, California. The speed and acceleration profiles under meter-on and meter-off scenarios were compared. Statistical results demonstrated that ramp metering affects drivers' acceleration behavior at ramp acceleration lane. It was found that at the metered ramp with short existing acceleration length, the average acceleration rate from ramp meter stop bar to 500 ft downstream under meter-on scenario (4.72 ft./s²) is approximately 40% higher than when meter-off (3.18 ft./s²). The design of acceleration lane length for metered on-ramps should therefore take into account the potential impacts of ramp metering on driver acceleration behavior.     

电动汽车动力电池热失控过程分析及预警机制设计

文章通过实验数据对热失控发生的过程进行分析,提取出关键的信号特征。设计出一套全面完整的热失控预警系统,并总结出多个报警条件,避免出现故障的误报及漏报的情况。最后介绍了热失控预警后整车及大数据的应对措施。