Development of a semi-empirical friction model in automotive driveshaft joints

High speed and sport utility vehicles with large joint articulation angle demand lower friction in automotive driveshaft joints to meet noise and vibration comfort levels. Thus a more thorough understanding of internal friction characteristics and mechanisms is required. In this paper, a friction model in automotive driveshaft joints was developed through the use of test data from an instrumented Constant Velocity (CV) joint friction apparatus with actual driveshaft assemblies. Experiments were conducted under different realistic operating conditions of oscillatory speeds, CV joint articulation angles, lubrication, and torque. The experimental data was used to develop a physics-based semi-empirical CV joint internal friction model as a function of different CV joint operating parameters. It was found that the proposed friction model captures the experimental results well. Also the friction model estimates the generated axial force (GAF) in tripod CV joints well, which is the main source of force that causes vehicle vibration problems.     

Development of a low-noise cooling fan for an alternator using numerical and doe methods

An alternator, which converts mechanical rotational energy into electrical energy, is an important component of a vehicle. Alternators operate over a broad range of rotational speeds, typically from 3,000 RPM to 18,000 RPM, which demands a cooling fan producing sufficient airflow, ideally with a minimum of noise. In the current study, an optimized alternator-cooling fan was developed through a linked DOE(Design OF Experiment) process and numerical analysis. The SC/Tetra and FlowNoise S/W programs were used to calculate flow rates and noise levels, respectively, for the newly developed fan. Compared with original model, the numerical results predicted a 3 dBA noise reduction; the measured reduction was 4 dBA.     

Model-based design of a variable nozzle turbocharger controller

Variable Nozzle Turbocharger (VNT) was invented to solve the problem of matching an ordinary turbocharger with an engine. VNT can harness exhaust energy more efficiently, enhance intake airflow response and reduce engine emissions, especially during transient operating conditions. The difficulty of VNT control lies in how to regulate the position of the nozzle at different engine working conditions. The control strategy designed in this study is a combination of a closed-loop feedback controller and an open-loop feed-forward controller. The gain-scheduled proportional-integral-derivative (PID) controller was implemented as the feedback controller to overcome the nonlinear characteristic. As it is difficult to tune the parameters of the gain-scheduled PID controller on an engine test bench, system identification was used to identify the plant model properties at different working points for a WP10 diesel engine on the test bench. The PID controller parameters were calculated based on the identified first-order-plus-dead-time (FOPDT) plant model. The joint simulation of the controller and the plant model was performed in Matlab/Simulink. The time-domain and frequency-domain performances of the entire system were evaluated. The designed VNT control system was verified with engine tests. The results indicated that the real boosting pressure traced the target boosting pressure well at different working conditions.     

Deflection test and transmission error measurement to identify hypoid gear whine noise

T-Hypoid gears are commonly used in rear-drive and 4WD (4 Wheel Drive) vehicle axles. Investigating their sensitivity to deflections is one of the most important aspects of their design and optimization procedures. Therefore, a deflection test was performed in this study in the actual gear mounting using completely processed gear. This test covered the full operating range of gear loads from “no load” to “peak load”. Under peak load, the contact pattern extended to the tooth boundaries without showing a concentration of the contact pattern at any point on the tooth surface. The transmission error was tested under an axle assembly triaxial-real-car-load condition.     

Development of a navigation algorithm with dead reckoning for unmanned ground vehicles

A navigation algorithm is indispensable for Unmanned Ground Vehicles (UGVs). During driving, UGVs follow a global path. In this study, we propose a navigation algorithm using Real Time Kinematic (RTK)-Differential Global Positioning System (DGPS) units and encoders to complement global path planning. Sometimes GPS systems lose their signals and receive inaccurate position data due to many factors, such as edifice and barrier obstructions. This paper shows that GPS deviations can be solved using a Dead Reckoning (DR) navigation method with encoders and that position errors can be decreased through the use of RTK-DGPS units. In addition to this method, we will introduce a new waypoint update algorithm and a steering algorithm using RTK-DGPS units.     

License plate extraction method for identification of vehicle violations at a railway level crossing

The primary cause of most railroad accidents is vehicle entry into railway level crossings despite warning messages. To identify drivers who violate railway level crossing regulations, vehicle license plate recognition can be applied at railway level crossings. The purpose of this paper is to present an effective method for extracting the license plate region from vehicle images taken at railway level crossings. The method proposed in this paper uses the variation in the gray-level values across the image of a license plate. For license plate region extraction, the character region is first recognized by identifying the character width and the difference between the background region and the character region. The license plate region is then extracted by finding the inter-character distance in the plate region. In addition, the license plate type is identified by the difference in the gray-level value between the background region and the character region. The proposed method is effective in solving the current challenges in extracting the license plate region from the damaged frames of license plates issued for domestic use, including new types of license plates. According to the experimental results, the proposed method yields a high extraction rate of 99.5% for vehicle license plates.     

Performance optimization of CVT for two-wheeled vehicles

Continuously Variable Transmission (CVT) is one of the most promising automotive transmission technologies because of its continuously variable gear ratio and reduced shift shock. CVT is different from Manual Transmission and Automatic Transmission, and it is possible to operate the power source in its high efficiency region with CVT in the drive train. Several types of CVT exist that can be categorized based on the mechanism of power transmission, such as the belt pulley, traction drive, and hydrostatic types. This paper investigates the belt pulley CVT, which consists of a thrust actuator, driver pulley, belt, driven pulley, and preload spring of the output shaft. A complete CVT is constructed, and based on that a simulation program that analyzes the static performance of a CVT is implemented in Matlab/Simulink. From these simulation results, methods for improving the efficiency of the CVT are discussed. The coefficient of the torque capacity factor is proposed as affecting the matching between a power source and a CVT, and methods for improving the matching effect are also investigated.     

Effect of fuel stratification on initial flame development: Part 3-high swirl condition

This paper discusses the final investigation into the effect of fuel stratification on flame propagation. In previous works, the characteristics under the no port-generated swirl condition and the low-swirl condition were considered. For this purpose, the initial flame development and propagation were visualized under different axially stratified states in a modified optical single-cylinder SI engine. The images were captured by an intensified CCD camera through the quartz window mounted in the piston. Stratification was controlled by the combination of the port swirl ratio and injection timing. These were averaged and processed to characterize the flame propagation. The flame stability was estimated by the weighted average of flame area and luminosity. The stability was also evaluated through the standard deviation of flame area and propagation distance and through the mean absolute deviation of the propagation direction. The results show that the LML is expanded remarkably under the high-swirl cases up to the highest relative AFRs of 1.71 and 1.75 between 140 and 160CA. In addition, similar to the low-swirl condition, the flame-flow interaction determines the direction of flame propagation, and the governing roles of the two factors vary according to the swirl level; the flow is more important at the higher swirl conditions, and the flame is more important at the lower swirl condition. Finally, fast and stable flame propagation can be achieved under the preferably stratified condition, which is induced by the suitable combination of the high swirl and injection timing.     

Experimental design influences on stated choice outputs: An empirical study in air travel choice

Discrete choice experiments are conducted in the transport field to obtain data for investigating travel behaviour and derived measures such as the value of travel time savings. The multinomial logit (MNL) and other more advanced discrete choice models (e.g., the mixed MNL model) have often been estimated on data from stated choice experiments and applied for planning and policy purposes. Determining efficient underlying experimental designs for these studies has become an increasingly important stream of research, in which the objective is to generate stated choice tasks that maximize the collected information, yielding more reliable parameter estimates. These theoretical advances have not been rigorously tested in practice, such that claims on whether the theoretical efficiency gains translate into practice cannot be made. Using an extensive empirical study of air travel choice behaviour, this paper presents for the first time results of different stated choice experimental design approaches, in which respective estimation results are compared. We show that D-efficient designs keep their promise in lowering standard errors in estimating, thereby requiring smaller sample sizes, ceteris paribus, compared to a more traditional orthogonal design. The parameter estimates found using an orthogonal design or an efficient design turn out to be statistically different in several cases, mainly attributed to more or less dominant alternatives existing in the orthogonal design. Furthermore, we found that small designs with a limited number of choice tasks performs just as good (or even better) than a large design. Finally, we show that theoretically predicted sample sizes using the so-called S-estimates provide a good lower bound. This paper will enable practitioners in better understanding the potential benefits of efficient designs, and enables policy makers to make decisions based on more reliable parameter estimates.     

Timetable-based operation in urban transport: Run-time optimisation and improvements in the operating process

Urban public transit provides an efficient means of mobility and helps support social development and environmental preservation. To avoid loss of ridership, transit authorities have focussed on improving the punctuality of routes that operate using timetables. This paper presents a new approach to generating run-time values that is based on analytical development and micro simulations. The work utilizes previous research (described herein) and the experience acquired by Transports Metropolitans de Barcelona (TMB) in operating bus routes based on timetables. Using a sample of historical data, the method used for generating run-time values consists of the following steps: purging and screening atypical trips, based on the consideration of confidence intervals for median trips; segmenting the day into time bands based on the introduction of a new hierarchical classification algorithm; creating initial run-time values based on criteria derived from statistical analysis; adjusting and validating initial run-time values using micro simulations; and evaluating incident-recovery times at the end of trips in order to guarantee the punctual departure of the next trip in the vehicle schedule. To favour service improvement, we also introduced certain indicators that can identify the root causes of non-compliance. As a final step, in order to ensure the applicability and use of the model, we promoted the development of our model within the framework of the HASTUS™ software solution.