Mixing over the steep side of the Cycladic Plateau in the Aegean Sea

Intensive microstructure sampling over the southern slope of the Cycladic Plateau found very weak mixing in the pycnocline, centered on a thin minimum of diapycnal diffusivity with Kρ=1.5×¹⁰−6 m² s^− 1. Below the pycnocline, Kρ increased exponentially in the bottom 200 m, reaching 1 × 10^− 4 m² s^− 1 a few meters above the bottom. Near-bottom mixing was most intense where the bottom slope equaled the characteristic slope of the semi-diurnal internal tide. This suggests internal wave scattering and/or generation at the bottom, a conclusion supported by near-bottom dissipation rates increasing following rising winds and with intensifying internal waves. Several pinnacles on the slope were local mixing hotspots. Signatures included a vertical line of strong mixing in a pinnacle's wake, an hydraulic jump or lee wave over a downstream side of the summit, and a ‘beam’ sloping upward at the near-inertial characteristic slope. Because dissipation rate averages were dominated by strong turbulence, ?/νN² > 100, the effect on Kρ of alternate mixing efficiencies proposed for this range of turbulent intensity is explored.     

Impact of phytoplankton community size on a linked global ocean optical and ecosystem model

We isolated the effect phytoplankton cell size has on varying remote sensing reflectance spectra (R_rs(λ)) in the presence of optically active constituents by using optical and radiative transfer models linked in an offline diagnostic calculation to a global biogeochemical/ecosystem/circulation model with explicit phytoplankton size classes. Two case studies were carried out, each with several scenarios to isolate the effects of chlorophyll concentration, phytoplankton cell size, and size-varying phytoplankton absorption on R_rs(λ). The goal of the study was to determine the relative contribution of phytoplankton cell size and chlorophyll to overall R_rs(λ) and to understand where a standard band ratio algorithm (OC4) may under/overestimate chlorophyll due to R_rs(λ) being significantly affected by phytoplankton size. Phytoplankton cell size was found to contribute secondarily to R_rs(λ) variability and to amplify or dampen the seasonal cycle in R_rs(λ), driven by chlorophyll. Size and chlorophyll were found to change in phase at low to mid-latitudes, but were anti-correlated or poorly correlated at high latitudes. Phytoplankton size effects increased model calculated R_rs(443) in the subtropical ocean during local spring through early fall months in both hemispheres and decreased R_rs(443) in the Northern Hemisphere high latitude regions during local summer to fall months. This study attempts to tease apart when/where variability about the OC4 relationship may be associated with cell size variability. The OC4 algorithm may underestimate [Chl] when the fraction of microplankton is elevated, which occurs in the model simulations during local spring/summer months at high latitudes in both hemispheres.     

俄罗斯新一代机车车辆(续完)——电气设备、车辆的模块化结构及客车的可靠性

6 电气设备 目前已确定了改善远景客运机车车辆的使用性能和运营性能的固定趋势,同时提高设备的质量和可靠性,导致了用电器品种和数量的增加,改进电气设备的结果提高了电能消耗量.由于节约电能是资源储备计划的组成部分之一,故无论对现有车辆还是远景车辆,均产生用电量优化的课题.     

Numerical simulation on truncated oval-nosed projectile penetrating into stiffened plate北大核心CSCD

[Objectives]In this paper, the numerical simulation method is used to study the anti-penetration performance and energy absorption mode of a stiffened plate, as well as the influence of different stiffened bars on the flight attitude of the projectile body.[Methods] Finite element software LS-DYNA is used to simulate the process of a truncated oval-nosed projectile penetrating a stiffened plate, and the results of the numerical simulation are compared with an experiment to verify the reliability of the numerical simulation method. The momentum method and mass equivalence method are used to predict the residual velocity of the projectile, and the applicability of different theoretical methods within different velocity ranges is compared. The deformation energy of different regions of the stiffened plate is then extracted to analyze the influence of the initial velocity of the projectile body on the energy absorption mode of the target plate. Finally, the structure of the stiffeners is changed and the influence of the relative position of the stiffeners on the penetration attitude of the projectile body is analyzed.[Results]The results show that the mass equivalence method is more accurate than the momentum method in predicting the residual velocity of the stiffened plate when the initial velocity of the projectile body is in the range of 300–900 m/s. The ratio of the deformation energy of the stiffened plate to the energy loss of the projectile body decreases with the increase of the initial velocity of the projectile body. The effect of a T-stiffened plate on trajectory is greater than that of a rectangular-stiffened plate.[Conclusions]The related calculation method and research results have certain reference value for research and engineering application surrounding the anti-penetration of stiffened plates. © 2023 Chinese Journal of Ship Research. All rights reserved.     

Performance of Two Types of Mooring Systems in the Heave Motion of a Two-body Floating Wave Energy Converter

Journal of Marine Science and Application - This work investigated the influence of two types of mooring systems on the hydrodynamic performance of a two-body floating wave energy converter (WEC)....     

A critical appraisal of the use of simple time-money trade-offs for appraisal value of travel time measures

Transportation - Stated choice surveys have established themselves as the preferred approach for value of travel time elicitation with the help of choice models. However, major differences exist in...     

Perceived risk of lock-in in the front-end phase of major transportation projects

Transportation - Lock-in is defined as the tendency to continue with an inefficient decision or project proposal. The front-end phase is critical to project success, yet most studies have focused...     

Commodity flow estimation for a metropolitan scale freight modeling system: supplier selection considering distribution channel using an error component logit mixture model

Freight forecasting models have been significantly improved in recent years, especially in the field of goods vehicle behavior modeling. On the other hand, the improvements to commodity flow modeling, which provide inputs for goods vehicle simulations, were limited. Contributing to this component in urban freight modeling systems, we propose an error component logit mixture model for matching a receiver to a supplier that considers two-layers in supplier selection: distribution channels and specific suppliers. The distribution channel is an important element in freight modeling, as the type of distribution channel is relevant to various aspects of shipments and vehicle trips. The model is estimated using the data from the Tokyo Metropolitan Freight Survey. We demonstrate how typical establishment survey data (i.e. establishment and outbound shipment records) can be used to develop the model. The model captures the correlation structure of potential suppliers defined by business function and provides insights on the differences in the supplier choice by distribution channel. The reproducibility tests confirm the validity of the proposed approach, which is currently integrated into a metropolitan-scale agent-based freight modeling system, for practical use.

     

A New Explicit Algorithm for Bi-Phasic Mixture Flow in MIM

Metal injection moulding (MIM) is a new technology to manufacture small intricate parts in large quantity. Numerical simulation plays an important role in its development. To predict the specific segregation effect in MIM injection, mixture theory is adopted to model the injection flow by a bi-phasic model. This model conducts to the solution of two-coupled Stokes equations. It is an extremely computational consuming solution in the scope of the traditional algorithms, which induce a serious challenge to cost-effectivity of the MIM simulation. Referred to some methods proposed by Lewis in mono-phasic simulation and the implicit algorithms in MIM simulation, a new explicit algorithm is proposed and realized to perform efficiently this type of bi-phasic flow. Numerically this algorithm is devised to perform the simulation in a fully uncoupled manner except for a global solution of the pressure field in each time step. The physical coupling is taken into account in a sequential pattern by fractional steps. This special algorithm does not need any iteration, so it is straightforward and robust, suitable for MIM simulation and other sorts of simulations for multi-phasic flow.