一种基于PLL的牵引电机速度辨识算法

提出一种基于PLL的速度辨识算法,在此算法中引入闭环转子磁链观测器和幅值归一化环节,弥补PLL本身在抗干扰能力上的不足.通过闭环转子磁链观测模型抑制了转子磁链中可能出现的直流偏置,引入幅值归一化环节抑制了可能出现的转子磁链幅值波动.在仿真软件中搭建模型进行验证,结果表明在电机速度指令突变以及负载转矩突变的情况下可以保持较好的辨识效果.通过仿真结果验证了所研究速度辨识算法的正确性和有效性.     

考虑横向漂移的船舶路径跟踪自抗扰控制

针对船舶运动系统中内部动态不确定和外部干扰等问题,进行了欠驱动船舶路径跟踪的自抗扰方法研究。利用Backstepping设计参考航向角,并通过线性扩张状态观测器对流干扰和横向运动引起的横向漂移进行估计。其次,根据自抗扰算法对航向进行控制,采用线性扩张状态观测器对外界干扰及内部不确定项进行估计。最后仿真结果表明,在风流干扰下所设计的控制器仍能使船准确地跟踪上参考路径,验证了所提控制方案的有效性。     

随着伊本·白图泰的足迹 游历中世纪的非洲、欧洲和亚洲——评李光斌翻译的《异境奇观——伊本·白图泰游记》

伊本·白图泰是14世纪著名的旅行家，他从摩洛哥出发，穿过阿尔及利亚、突尼斯、利比亚、埃及、叙利亚到麦加完成第一次朝觐。后来他又到过东非各国、印度、东南亚国家和中国等。李光斌老先生翻译的《异境奇观——伊本·白图泰游记》是目前最完整的全译本，当我阅读此书时，好象是跟随伊本·白图泰游历中世纪的非洲、欧洲和亚洲。李光斌老先生不仅翻译准确，达到了“信”、“达”、“雅”的境界，而且注释详尽，在考据学上也颇有作为。     

“资本是一个活生生的矛盾”——对马克思一个重要命题的当代解读

要科学回答2008年国际金融危机的发生根源,就要深刻认识马克思的“资本是一个活生生的矛盾”的命题.在马克思看来,为了获取剩余价值,资本必然会推动生产无限扩大；为了实现剩余价值,资本必须保持生产和消费的正确比例从而限制生产的无限扩大趋势,这两者共同构成了资本的矛盾本质.不难发现,这次国际金融危机的根源是资本矛盾本质决定下的生产相对过剩.资本矛盾命题具有重要的当代启示,即应当坚持资本和资本主义的分离、坚持基本经济制度的社会主义性质、坚持以科学发展观来规划和调整经济的发展道路和发展方向.     

艰险山区铁路桥隧工程技术接口管理成熟度评价研究

艰险山区环境恶劣、地质复杂,使得铁路桥隧工程施工技术难度高、施工周期长,导致技术接口多、管理难度大.为实现对桥隧工程技术接口科学有效的管理,提出一种基于变权-靶心贴近度的艰险山区铁路桥隧工程技术接口管理成熟度评价模型.利用WSR系统方法对技术接口问题进行分析,构建铁路桥隧工程技术接口管理综合评价指标体系,并通过变权综合模型为指标赋权.运用靶心贴近度模型确定桥隧工程技术接口管理成熟度.以藏木雅鲁藏布江特大桥与安拉隧道为例,用该模型评估其技术接口管理成熟度等级,并借助雷达图直观反映技术接口管理水平.通过本文研究为艰险山区铁路桥隧工程技术接口管理提供了新思路.     

压载水旋流预处理单元的优化设计与数值模拟

压载水管理公约D2对压载水中颗粒物粒径范围及含量做出了明确规定。为满足此规定,水力旋流器逐步开始应用于船舶压载水处理系统中。为了提高水力旋流器的分离效率,通过改变水力旋流器的入口结构对水力旋流器进行优化,即将入口结构设计为阿基米德螺线形入口来增加流体转动速度,降低能量消耗,从而提高分离效率。应用Fluent软件,结合雷诺应力模型(RSM)和混合多相流(Mixture)分析方法,对优化前、后的水力旋流器进行固-液两相流数值模拟。模拟内容包括水力旋流器内的速度分布、固相体积分数分布以及分离效率等。通过对比2种模型的模拟结果,说明优化的水力旋流器内部的流场速度以及分离效率均有一定的提高,达到了优化目的。     

铺缆船用电缆埋设犁土壤挖掘阻力计算

传统的计算埋设犁土壤挖掘阻力的方法一般采用经验公式计算。经验公式依赖丰富的试验数据，且只能适应特定形状和尺寸的埋设犁。由于埋设犁的形状和尺寸各不相同，基于经验公式计算土壤挖掘阻力的方法准确性不高。根据土力学基本原理，在力学分析的基础上，运用数学方法进行公式推导，得到用于计算不同形状尺寸埋设犁挖掘阻力的理论方法，解决依赖经验公式计算土壤挖掘阻力的局限性。     

熔融石英砂动力特性动三轴试验

为探究振动荷载作用下熔融石英砂液化破坏过程中动变形和动强度变化规律, 促进透明土技术在岩土工程动力特性可视化模型试验中的推广和应用, 对构成透明砂土骨架结构的典型粒径(0.5~1.0 mm)熔融石英砂开展饱和试样动三轴试验; 研究了不同围压、加载频率和动应力比等试验条件下熔融石英砂试样的累积轴向应变、动孔压发展模式、动应力衰减、动弹性模量和阻尼比的变化规律, 并将试验结果与相同级配的标准砂进行了对比。分析结果表明: 熔融石英砂累积轴向应变随动应力比的增大呈现出由稳定型向破坏型转变的趋势, 加载频率为0.5~1.5 Hz时, 临界动应力比为0.150~0.175, 小于标准砂的0.200~0.225;升高围压、增大动应力比、降低加载频率会加快试样塑性应变累积, 缩短液化破坏时间; 熔融石英砂孔压发展模式随围压增大逐渐由Seed孔压模型向指数型过渡, 增大加载动应力会加剧液化破坏后孔压的振动幅度; 相同动应力比下, 熔融石英砂与标准砂的动应力与动应变呈现线性相关, 在围压大于200 kPa时, 二者动应力衰减幅度随围压的增大而逐渐减小; 熔融石英砂的动弹性模量和阻尼比表现为线性关系, 动弹性模量随动应变的增大呈现出双曲线型减小的趋势, 并随围压的增大而增大; 阻尼比随动应变的增加先增大后基本稳定在0.22, 发展曲线受围压影响较小。      

Reliability Modeling and Maintenance Policy Optimization for Deteriorating System Under Random Shock

Performance degradation and random shock are commonly regarded as two dependent competing risks for system failures. One method based on effective service age is proposed to jointly model the cumulative effect of random shock and system degradation, and the reliability model of degradation system under Nonhomogeneous Poisson processes (NHPP) shocks is derived. Under the assumption that preventive maintenance (PM) is imperfective and the corrective maintenance (CM) is minimal repair, one maintenance policy which combines PM and CM is presented. Moreover, the two decision variables, PM interval and the number of PMs before replacement, are determined by a multi-objective maintenance optimization method which simultaneously maximizes the system availability and minimizes the system long-run expect cost rate. Finally, the performance of the proposed maintenance optimization policy is demonstrated via a numerical example.     

Occupant injury risk analysis at NASS/CDS database

Injury information for vehicle occupants from the body regions of the head, thorax, abdomen, and upper and lower extremities, due to the restraints and interior parts of the vehicle, were extracted from the 2009 ~ 2012 NASS/CDS database. For those cases with high occurrence frequency, a detailed and comprehensive data analysis was performed to find the relationship between the accident, occupant, vehicle, and injury data. A numerical frontal impact sled model with the Hybrid III dummy and the GHBMC human body model was constructed to simulate and identify those injury risks according to NASS/CDS. Among the 5,734 injuries to the aforementioned body regions from frontal crashes are, listed by frequency of occurrence, the lower extremity (27.8 %), upper extremity (21.3 %), thorax (15.1 %), face (10.9 %), spine (8.7 %), head (7.3 %), and abdomen (6.9 %). The main injury sources to the head were the windshield, side structure, and steering wheel. For the thorax and abdomen they were the seat belt and steering wheel. For the lower extremity it was the instrument panel. The main injury patterns for the head were the concussion and the contusion. For the thorax they were vessel laceration and lung contusion. For the abdomen they were laceration and contusion of the organs. For the lower extremity they were bone fracture and ligament rupture. The steering wheel and seat positions were main factors affecting head and thorax injury risks. From the sled impact simulation, high injury risks of the head and thorax were assessed respectively at conditions of steering column tilt down and rear most seat position, which correlated well with the findings from the NASS/CDS data analysis.